STC01 Built in Non Removable
Rechargeable Lithium Battery
User Manual

Quick instructions

1. Turn on the device
   ▪ Press and hold the button for 5 seconds, the device will beep and turn on.
2. Pair the device
   ▪ Open the Find My app.
   ▪ Hold the device close to your iPhone, tap the Items tab, tap + and then Add Other Item.
   ▪ Tap Connect SXXXXX.
   ▪ Type a name for your device, select an emoji.
   ▪ Tap Agree to acknowledge that this item will be linked to your Apple ID.
   ▪ Tap Finish.
3. Enable Lost Mode
   ▪ Open the Find My app, tap the Items tab, then tap your item.
   ▪ Under Lost Mode, tap Enable.
   ▪ Read the instructions, tap Continue and enter a phone number or email address.
   ▪ Confirm the information, customize the lost message, and tap Activate to complete the setup.
4. Remove the device
   ▪ Open the Find My app, tap the Items tab, then tap your item.
   ▪ Tap Remove Item and then tap Remove to complete the operation.
5. Charging method
   A: Wireless charging
   ▪ Place the card tracker on a wireless charging device that supports QI standard.
   ▪ Make sure the charging side (as the picture1) of the card tracker is aligned with the charging device. The red charging indicator light is on, which means it is charging
   ▪ When fully charged, the indicator light will turn green.
   B: Magnetic charging (limited to products with magnetic touch spot)
   ▪ Use the included magnetic charging cable to charge.
   ▪ Connect the charging spot of the card tracker to the charging cable magnetic head . When connected correctly, the magnetic suction will automatically absorb.
   ▪ Connect the charging cable to the USB-A interface of the power adapter The red charging indicator turns on means the device is charging.
   ▪ When fully charged, the indicator light will turn green.
   *Note: A power adapter with an output voltage of 5V is required
   

Instructions for device button

1. Power on
   Long press the button for five seconds, the device will beep, the light will flash three times, and the device will be turned on.
2. Device status confirmation
   Double-click the device button, the device will beep, and the light will flash three times, indicating that the device is working. If the device does not ring, the device is off. Long press the button for five seconds to turn it on.
3. The device enters the pairing state again
   After removing the device in the app, the device will beep and the light will flash six times, it will not shut down and will be in the pairing mode. If there is no re-pairing within 10 minutes, the device will leave the pairing state. If you want to pair a device at this time, you need to click the device button once, the device will beep, and the light will flash once. At this time, the device enters the pairing state and can be paired with the app again.
4. Factory Reset
   First, remove the item from Find My app, then, after the device is powered on, double-click the device button. The device will beep. Long press the device button for six seconds until the device beeps and the light flashes three times.
   Release the button to complete factory reset. The device can now be paired.
5. Power off
   When the device is on, press the device button 5 times in 2 seconds. The device will beep, the light will flash three times, the device will be powered off.

FAQ

How to confirm whether the device has been turned on?

▪ Double-click the device button, the device will beep, and the light will flash three times, indicating that the device is working. If the device does not ring, ▪ the device is off. Long press the button for five seconds to turn it on.

NFC Tag Function Settings

(Only the product with NFC tag function)

1. Ensure that your mobile phone supports the NFC function and enable NFC in the phone settings.
2. Open the NFC Tool App and go to the “NFC Settings” page.
3. Set
   the NFC function according to the prompts, for example:
4. Set the contact phone number.
   ▪ Share the electronic business card.
   ▪ After the settings are completed, bring your mobile phone close to the NFC area (as the pricutre ) of the card tracker to trigger the corresponding function.

<p>Notice

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
   (1) This device may not cause harmful interference.
   (2) This device must accept any interference received, including interference that may cause undesired operation.
   Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
2. le="text-align: justify">This device has been tested and complies with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
   This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
3. If this device does indeed cause harmful interference to radio or television reception, which can be determined by turning the device on and off, users are encouraged to try to correct the interference by one or more of the following measures:
   (1) Reorient or relocate the receiving antenna.
   (2) Increase the separation between the equipment and receiver.
   (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
   4) Consult the dealer or an experienced radio/TV technician for help.
4. le="text-align: justify">This device has been evaluated and found to meet general RF exposure requirements.
5. This device may be used under portable exposure conditions without restriction.

<p style="text-align: justify">Important Tips
When pairinga device with Findmy app, the phone will link to the Apple server.
Pairing may fail because of network problems.The following actions are recommended:

1. Change the phone’s network, such as switching between WiFi and mobile network;
2. le="text-align: justify">Factory Reset for the device:
   When the device is powered on, double-click the device button.The device will beep,then immediately long press the device button for eight seconds until the device beeps for the second time and the indicator light flashes, Releasethe button, Factory Reset is completed.
   Note:
   After long pressing the device button for 2 seconds,the device will sound “tick,tick, tick”, and the indicator lnear the button flashes.Do not release it. Continue to press and hold the button until the device emits a musfor the second time, and the indicator light flashes. Releasethe button.
3. Restart the Apple device (such as iPhone or iPad).
4. le="text-align: justify">Pair the device with the Find App again.

Battery Warning:
This device uses a built-in, non-removable rechargeable lithium battery.
Failure to follow the guidelines below may shorten the lifespan of the lithium-ion battery inside the device or cause a fire!

i>Do not disassemble, puncture, or damage this device.
• Do not remove or attempt to remove the internal battery that is not user-replaceable.
• Do not expose this device to flames, explosions, or other hazards.

Any problem or suggestion,
please contact: admin@singsun.com.hk

Documents / Resources

Singsun STC01 Built in Non Removable Rechargeable Lithium Battery [pdf] User Manual 2BEM5-STC01, STC01 Built in Non Removable Rechargeable Lithium Battery, STC01, Built in Non Removable Rechargeable Lithium Battery, Non Removable Rechargeable Lithium Battery, Rechargeable Lithium Battery, Lithium Battery, Battery

References

• User Manual