SimpliSafe CMOB1 Wireless Outdoor Security Camera User Guide

simplisafe logo

SimpliSafe CMOB1 Wireless Outdoor Security Camera

SimpliSafe CMOB1 Wireless Outdoor Security Camera

CMOB1 FCC Statement Procedure

  1. Quick Start Guide in Box tells users to download appgetting started
  2. App links to FCC Statement
    Main Menu > Setting > FCC Statement

app links

Federal Communication Commission Interference Statement

The devices listed above comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) The devices may not cause harmful interference, and (2) the devices must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Industry Canada Statement

This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with greater than 20cm between the radiator & your body.

Documents / Resources

PDF thumbnailCMOB1 Wireless Outdoor Security Camera
User Guide · CM3000, U9K-CM3000, U9KCM3000, CMOB1 Wireless Outdoor Security Camera, CMOB1, Wireless Outdoor Security Camera

References

Questions and answers

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Questions & Answers

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

  1. Completely useless article. Camera just refuses to work, with a blinking blue light.

    Anonymous asks Completely useless article. Camera just refuses to work, with a blinking blue light.
    Manuals+ clarified question
    Question

    What does a blinking blue light mean on my SimpliSafe CMOB1 Wireless Outdoor Security Camera?

    Answer

    A blinking blue light on the SimpliSafe Wireless Outdoor Security Camera (CMOB1) typically indicates that the camera is in pairing mode and is ready to be set up in the SimpliSafe app.

    If your camera is stuck in this state or refuses to work, please try the following steps:

    • Check the Battery: Ensure the battery is fully charged. Charging takes approximately 5 hours; the 3 LEDs on the battery will light up when it is fully charged.
    • Use the App: Open the SimpliSafe mobile app, select "Set up a camera," and follow the on-screen instructions to complete the connection.
    • Reset the Camera: If the camera is unresponsive, you can perform a reset by holding down the setup button on the back of the camera for 20 seconds. Release the button, and the camera should reboot and return to a blinking white or blue light to indicate it is ready for setup.
    • Check Wi-Fi: Ensure your Wi-Fi signal is strong at the camera's location and that you are connecting to a 2.4GHz network.

    If the blinking blue light persists and you cannot complete setup, you may need to contact SimpliSafe technical support via the "Help & Support" section in the app.

  2. Why my ourdoor camera is not connecting to my wifi?

    🇺🇸 Anonymous asks Why my ourdoor camera is not connecting to my wifi?
    Manuals+ clarified question
    Question

    Why is my SimpliSafe CMOB1 outdoor camera not connecting to my Wi-Fi?

    Answer

    If your SimpliSafe CMOB1 Wireless Outdoor Security Camera is having trouble connecting to Wi-Fi, please check the following troubleshooting steps based on the setup guide:

    • Check Battery Level: Ensure your battery is fully charged. A full charge takes approximately 5 hours, and all 3 LEDs on the battery will light up when it is ready.
    • Use the SimpliSafe App: Open the SimpliSafe mobile app, select "Set up a camera," and follow the on-screen instructions carefully.
    • Wi-Fi Frequency: Ensure your router is broadcasting a 2.4GHz signal, as most SimpliSafe cameras require this frequency rather than 5GHz.
    • Signal Strength: If the camera is already mounted, try bringing it closer to your router to see if the connection establishes. If it does, you may need a Wi-Fi extender for its outdoor location.
    • Reset the Camera: If the app fails to find the camera, you may need to reset the device by pressing the setup button on the back of the camera (near the battery compartment) and attempting the app setup again.

    If you continue to experience issues, you can contact SimpliSafe Technical Support through the app by going to the Main Menu > Help & Support.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.