Simpled SF-SP Smart Lock User Manual

Simpled SF-SP Smart Lock

PRODUCT PICTURE AND LIST

• Product Picture
  The pictures used in the installation manual are for reference only, and the product is subject to the actual product.
• PRODUCT LIST
  After unpacking, please check carefully according to the list, if you find any omissions, please ask us for it in time.

PRODUCT INTRODUCTION

Note: Default admin password in initialization state: 123456 or 000 or 000000

Restore Factory Setting
Press and hold the reset button on the lock and enter “000000#”. The lock will restore to factory settings, clearing all passwords and mobile administrators.

How to Connect the “TT Lock” App?

Download the App
Please search “TT Lock” in the app store to download.

• Step 1: Select the box in the upper left corner
• Step 2: Select [Add Lock]

• Step 3: ASSIN a Name for it
• Step 4: WiFi connection
• Step 4: Success

Only in the factory state can it connect to the internet. The APP interface will be continuously updated, and the images are for reference only. Please refer to the actual interface.
To enable remote unlocking, ensure that the remote switch is turned on and Wi-Fi sleep mode is disabled (this will increase power consumption and reduce battery life; it is recommended to keep Wi-Fi sleep mode enabled during normal use).

 Change the Administrator Password

The operation must be near the lock.

Add other Phone Administrator

• After adding an administrator password or a phone administrator you can enter 83# administrator password #” to allow the other App account to add the lock again.
• The previous account will be deleted after the new account added.

Delete mobile administrator

• To select the APP to delete the lock of the mobile phone administrator, click the settings, and click to delete.
• After deleting the administrator on the APP, the lock is restored to the factory settings. All fingerprints, passwords, and cards added before were invalidated.

OPERATING INSTRUCTION

Change the Administrator Password
The operation must be near the lock.

Fingerprint Setting

 Add Fingerprints

There are Timed/Permanent/Recurring fingerprint types on the app.

Delete Fingerprints

Edit Name 

Passcodes Setting

There are Timed/One-time/Permanent/Custom/Recurring/Erase password types on the app.

Delete Passcode 

 Edit Passcode 

 Change Period 

Cards Setting

 Change Period 

• Chinese : press “*39#administrator pass code#1#”on keypad.
• English: press “*39#administrator pass code#2#”on keypad.

HOW TO USE

Password Unlock

• Enter the added password, press # to confirm, password verification success
• Press down the handle to unlock.

Fingerprint Unlock

• The added fingerprint has been placed on the fingerprint sensor in the correct way, the fingerprint verification success
• press down the handle to unlock.

Emergency Unlock

Mechanical Key Unlock

•  Insert the key into keyhole.
• Turn the key and press down handle to unlock.

USB Emergency Power Supply
When the battery is exhausted and there is no key, you can connect an external power bank or 5V1 A power supply for emergency, and open the door according to the normal operation steps. Please replace the battery in time after the emergency unlock.

Battery Level Detection

When the battery voltage is below 4.8V, it can be recognized normally and the voice plays “Low battery, please replace”. Attention please replace the battery.

 Door Lock

One-Touch lock/unlock
Short press the button can lock/unlock

Thumb Turn
Rotate the thumb turn can lock/unlock

INSTALLATION STEPS

1. Install bolt in door.
   Note: The bolt must be in a retracted (unlocked)position when installing the lock set. Install strike on the door frame, making sure to allow for the bolt to be centered in the strike.
2. Install exterior assembly As you position the outside assembly, route the cable through the hole.
   Note: cable goes BELOW bolt.
   
3. Secure the mounting plate Holding the outside assembly flush to the door, position the inside mounting plate by first routing the cable and connector through the mounting plate hole. Secure the mounting plate with screws.
4. Connection cable Attach cable assembly to the inside assembly PCB. Press connector in firmly using thumbs until completely seated.
   
5. Mounting plate with screws Install and secure the inside assembly into the mounting plate with screws.
6. Test the lock and check door alignment
   IMPORTANT: Before installing the batteries, test the mechanical operation of the lock by using both thumb turn and the key. The movement of the bolt should be smooth and unobstructed. If operation is not smooth, review the previous steps to ensure proper installation.
   
7. Installing the battery Insert four (4) AA alkaline batteries and install battery cover. install successfully.
   
8. Built-in Door Sensor The smart lock is designed with built-in door magnet sensor to enable auto-lock function. To set up the door sensor, slide the sensor from the back of interior assembly, You may need to remove the interior assembly from the door to slide the sensor Stick the magnet to the door frame and make it close to the sensor.

FCC STATEMENT

Federal Communications Commission (FCC) Statement. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide Reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of·1 the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications made to this device not expressly approved by may void the FCC authorization to operate this device

Note: The manufacturer is not responsible for any radio or TV interference caused by un authorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

RF exposure statement:
This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The device is installed and operated without restriction.