Nothing But Net With Shot Tracker User Guide

Step 2: Alignment
Place the unit at the desired position on the barrel. Tighten the middle screw on the mount using the provided screw driver or T-wrench. Maintain vertical alignment with the ShotTracker’s camera directly below the barrel.

Step 3: Power On/Off
If the ShotTracker does not boot up and continues blinking red, press and hold the On/Off button for approximately 10 seconds until you see a fast blinking red LED. Release the button to turn off the unit.

Step 4: Shot Results
Complete a profile with valid boresight to start a new session. Access shot information specific to each game type (skeet, trap, sporting clays, helice, special) by pressing on the bottom right of the Results screen.

Precautions
Read and follow all safety instructions provided by the gun manufacturer before handling or installing the ShotTracker. Failure to follow safety guidelines may result in injury or damage.

Kit Contents

ShotTracker
4 Batteries, Charger and Cable
Hex Driver
Sub-Gauge Barrel Pad Kit
Lens Cloth
Quick Reference Guide and Auto-boresight Target Template

Getting Started

Charge Batteries – Connect battery charger to USB power source. Place the batteries in the charger. Once all four red LED are solid ON, the battery is charged. If all four red LEDS blink in unison the charging process did not start. If this happens pull the battery out of the charger and reinsert.

Mounting the ShotTracker

Step 1 – Loosen Screws
Remove the ShotTracker from the storage case. Use the 9/64” Allen driver to loosen the three mounting screws to open the clamp on the multi-guage barrel mount.

Step 2 – Place ShotTracker on Shotgun
Insure the protective rubber pads are properly attached to the barrel mount and slide the mount onto your shotgun’s barrel. Place the ShotTracker as far back on the barrel as you like. Just be sure to leave enough space to activate the On/Off button.

Step 3 – Alignment
Once the unit is placed at the desired position on the barrel, snug up the middle screw on the mount using the screw driver / T-wrench. Be careful to maintain a vertical alignment where the ShotTracker’s
camera is directly below the barrel.

Step 4 – Securely Tighten
When the unit is properly aligned, tighten all three mounting screws. Do Not Over Tighten – Max Torque 15 in-lbs.

Initial Set Up

ClayTracker Pro App – go to your phone’s app store and download the ClayTracker Pro app

Next, install fully charged batteries into the ShotTracker (button side up) and press the ON/OFF button. After ten seconds (11 red flashes) the LED will begin to flash magenta.
On your smart phone go to the WiFi section in Settings. Look for a WiFi network with a label that starts with “ST_ “ and matches the SSID listed inside the ShotTracker battery door.

Select that WiFi Network and enter the Passcode that is located on the inside of the battery door.
Once connected, start the ClayTracker Pro app.
When prompted allow the app to find and connect to devices on the local netowrk and answer “Yes” to all of the questions. The app will then “sync” to the ShotTracker.

From the Maim Menu on the app, select the ShotTracker button to make sure you seee “Connected” at the top of the page. Press the Firmware Update button to verify that you have the latest ShotTracker firmware.

ShotTracker LED

Slow Blinking Red: Booting up
Red Flash: Low Battery (every 5 sec.)
Green: Ready for Shot
Blinking Green: Processing Shot
Blue Flash: Connected to ClayTracker Pro app
Solid Purple: IDLE mode – power saving
Flashing Purple: ShotTracker is Reset to Factory Settings. Complete a Profile with a valid Boresight to start a new session.

If the ShotTracker does not boot up (continues Blinking Red), press and hold the On/Off button for ~10
seconds until you get a fast Blinking Red LED then release the On/Off button to turn the unit off.

Setting Up a Profile

Connect to the ShotTracker. From ClayTracker Pro app’s Main page select Profiles and then press Add Profile

Enter the required information including your shotgun type.
Select the choke type and ammo details. (do this twice for O/U and SxS)
Next select clay type – default is Standard
If you know the POI of your shot gun, enter that information next, Otherwise leave the default 50/50 at 40 yards setting

Press Save when done.

Performing a Boresight

Take the clay auto-boresight image included in your kit and place it on a vertical surface 15-25 yards away.
Press the Set Boresight button at the bottom of the Profile

Stabilize your shotgun on a gun rack or by leaning against a pole. While aiming at the clay image, press the Begin Auto Boresight button at the bottom of the page and wait for the Beep. It is very critical to keep your shotgun very still and stable during the last two seconds of the boresighting process while the gyros are calibrated.
If the Auto Boresight process is successful, after the “beep” you will see a photo with a red reticle placed on top of the clay image along with the distance to the clay image in red. If the distance is correct (+/- a yard), press the Verified button.

If the Auto Boresight process cannot complete after a couple of tries, use the Manual Boresgight process.

Final Step

Once you have a competed Profile along with a valid Boresight, press the Let’s Shoot buttom from the Main page.

Press Start New Session and eneter a description of where you are shooting. Then select your game (skeet, trap ….) along with the Profile you will be using.
Press Continue and you shold see the “Waiting for First Shot” banner.
The LED will turn solid green and the ShotTracker is now ready to go.

Supported Clay Sports
ShotTracker supports skeet, trap, sporting clays, helice and special. The Shot Results screen for each of these game types is designed to provide the important shot information for that game. For a detailed list of all shot data for your shot , press on the bottom right of the Results screen.

Precautions
Read all of the gun manufacturer’s safety information and safety instructions before handling the shotgun, installing the ShotTracker, or using the ShotTracker on a shotgun. Read and apply all of their instructions before using the ShotTracker to avoid injury.

WARNING: Failure to follow these safety instructions could result in fire, electric shock, or other injury or damage.

FCC Statement

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in particular installation.

Industry Canada:
This Class B device meets all requirements of the Canadian Interference Causing Equipment Regulations.

ShotTracker
Contains FCC ID: TFB-1004
Contains IC: 5969A-1004

www.TakeAimTech.com

ShotTracker is covered by US Patents 10,782,096 and 10,634,454. Other Patents Pending.

FAQ

Q: What should I do if the ShotTracker does not power on
A: If the ShotTracker does not boot up and continues blinking red, press and hold the On/Off button for approximately 10 seconds until you see a fast blinking red LED. Release the button to turn off the unit.

Q: How can I access shot information for different game types?
A: Press on the bottom right of the Results screen to view shot information specific to each supported game type (skeet, trap, sporting clays, helice, special).

Documents / Resources

SHOT TRACKER Nothing But Net With Shot Tracker [pdf] User Guide
Nothing But Net With Shot Tracker, But Net With Shot Tracker, With Shot Tracker, Shot Tracker

References

User Manual

Nothing But Net With Shot Tracker

Specifications

Product Usage Instructions