Shenzhen S1 Smart PTZ Camera
Specifications
- Model: Smart PTZ Camera S1
- Features: 4G LTE antenna, Microphone, White light, Indicator light, Lens, Human body infrared sensor, Speaker, TF card slot, USB Type-C port, Cloud card slot
Product Usage Instructions
Mounting the Camera
Attach the camera to the installed bracket and push it in place.
Solar Panel Installation
- Select an appropriate location for the solar panel and secure the mounting bracket.
- Attach the solar panel to the bracket and adjust its angle to ensure adequate sunlight reception.
- Tighten the adjustment knob to lock the panel in place.
What’s in the box
Product appearance
Quick start
You can search CamVigil APP in the app store, and complete the user registration process in the app.
Bind The Camera
- Step 1: Open the app, tap the “+ Add device” on the front page or the ”
” button in the top-right corner and select your device type.
- Step 2: Turn the power switch to the “ON” position, then press and hold the “RESET” button for 5 seconds until the voice prompt is given and the blue indicator light flashes. Tap “Next step”.
- Step 3: Choose your preferred way to add the camera.
- Add via Bluetooth
This allows automatic searching for nearby enabled devices
- Add by scanning the device’s QR code
Use your phone to scan the QR code on the device body Ensure the device is in pairing mode
- Add by scanning the phone’s QR code
Place the QR code generated by your phone 15–25 cm right ahead of the device
Once the device successfully scans the QR code, you’ll hear prompting beeps
Install the camera
It’s highly recommended to fully charge the device before installation.
Choose the installation location
Install the camera in a location with a clear line of sight and a robust 4G signal.
- For outdoor use, mount the camera at a higher location to maximize its waterproofing and the effectiveness of the PIR motion sensor.
The PIR sensor is more sensitive to motion within the camera’s field of view than to movement toward or away from the camera. - When the device is powered by a solar panel, choose a location free from obstructions to enhance charging efficiency.
Install the mounting bracket
Note: A screwdriver or drill is required.
Wall mounting
- Drill holes with a drill bit at the desired location for the bracket.
- If your wall is made of concrete, brick, or plaster, hammer expansion tubes into the wall and then insert screws.
- If your wall is made of wood or vinyl, you can directly insert the screws without the tubes.
- Mount the bracket securely on the wall.
Ceiling mounting
- Drill holes with a drill bit at the desired location for the bracket.
- If your wall is made of concrete, brick, or plaster, hammer expansion tubes into the wall and then insert screws. If your wall is made of wood or vinyl, you can directly insert the screws without the tubes.
- Mount the bracket securely on the ceiling.
Mount the camera
Attach the camera to the installed bracket and push it in place.
Install the solar panel
Select an appropriate location for the solar panel. Secure the mounting bracket and attach the solar panel to the bracket. Adjust the angle of the solar panel to ensure it receives adequate sunlight, and tighten the adjustment knob to lock the panel in place. (For solar panel installation methods, please refer to the solar panel manual.)
Note
- Choose a location that receives the most direct sunlight throughout the day. If in the Northern Hemisphere, tilt the solar panel upwards at a 30-degree angle. Keep it facing south if in the Northern Hemisphere, or facing north if in the Southern Hemisphere.
- Clean the surface of the solar panel with a soft, damp cloth regularly to remove dust or debris.
Note
The solar panel works within a temperature range from 0°C (32°F) to 45°C (113°F). It will not charge the camera in temperatures below 0°C (32°F) or above 45°C (113°F). In such cases, place the camera indoors and charge it using a 5V 2A power adapter.
Connect the solar panel to the camera
Open the rubber cover on the camera and connect the solar panel’s cable to the camera’s Type-C USB port.
With this feature, you can share the camera with other family members or your friends when needed. Only the administrator who initially binds the camera can share and configure the camera, while other members can only access the real time videos or video playback.
- For the camera administrator, navigate in the top-right corner of the app’s front page to “Family Name → Family Management → Create New Family → Add Member”.
- The invited users will receive a family invitation notification. They can tap “Agree” to complete the camera sharing process.
Indicator light status
| Blue light always on | Works properly |
| Blue light flashes quickly | Connecting to network |
| Blue light flashes slowly | Device bound |
| Red light always on | Charging completed |
| Red light flashes quickly | Charging error |
| Red light flashes slowly | Charging in progress |
| No Light | Sleeping/Powered off |
Product specification
| Image resolution | MaX. 2304X1296 |
| Video bit rate | Adaptive |
| Storage media | TF card (Up to 256GB) |
| Rotation Angle | 320° pan, 90° tilt |
| Battery capacity | 9200mAh |
| Adapter requirement | 5V/2A |
| Size (without bracket) | 146×130×108mm (in) |
Safety
- Do not use the device in extreme temperatures, and never expose the device to strong sunlight or a humid, wet environment.
- The suitable temperature and its accessories is -10°C/14°F to 45°C/113°F (The temperature for charging is 0°C/32°F to 45°C/113°F).
- The optimal environment is a temperature range between 5°C/41°F and 25°C/77°F.
- When charging, please place the device(s) at room temperature in a place with good ventilation.
Warning
- Replacing the battery with an incorrect version can damage the safety mechanisms within the device.
- Improper battery disposal, for example, into a fire or a hot oven, or mechanically crushing or cutting the battery, can result in an explosion.
- Leaving a battery in a very high-temperature environment can result in an explosion or the leakage of flammable liquid or gas.
- A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
FCC warning:
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Contact Us
For any inquiries, feel free to contact us. We will respond as soon as possible.
- E-mail: After-saleservice011@outlook.com
- Tel: 1-888-258-1230
- Manufacturer: Shenzhen Efercro Electronic Technology Co.,Ltd. Address: Room 901, Block E, Building 1, Section 1, Chuangzhi Yuncheng, Liuxian Avenue, Xili Community, Xili Street, Nanshan District, Shenzhen
FAQ
How do I download instruction manuals in different languages?
Please scan the QR code provided in the Quick Start Guide to download instruction manuals in German, Italian, French, Spanish, and Japanese.
How to use PIR human detection function, why is there alarm when there is no one?
PIR is a far-release infrared sensor, which is based on the human body's far-release infrared to determine whether people are active. There are other objects in nature that have the same wavelength of infrared, such as sunlight, mammals, and cars and heat sources. Serious electromagnetic interference can also cause false triggers to the equipment. The interference of the PIR sensor can be reduced by the following means. a, Try to avoid direct sunlight, solar cameras and other outdoor products. Radar technology has been added, therefore, there is no need to avoid direct sunlight. b, Where there are more people, it is recommended to turn off the PIR or turn down the sensitivity to reduce false alarms.
How does the battery run out of power for a few days?
Low-power products use a combination of extremely low-power dormancy and fast remote wake-up, which significantly extent battery life and if the battery consumes electricity faster, check the following points: a, For safe transport, the battery is usually in a state of about 50% electricity, therefore, it needs to be charged before use. b, Frequent PIR triggers could quickly consume battery power, and it is recommended to set PIR for low sensitivity or shutdown in complex environments c, Battery life is typically calculated by watching 20 times a day. Frequent or prolonged viewing of the device can also lead to rapid electricity consumption. d, In the case of network instability, the device needs to restart and maintain normal communication with the server. The environment of network instability is related to the number of system wake-up, and the networks which is highly unstable can also lead to faster battery power consumption.
What are the requirements for memory card for this product?
This product is frequently started video product. which is need memory card requirements are relatively high, it is recommended to use genuine 256GB TF card, please format TF card before use. Because this product is not a full-time video product, the general 16GTF card can meet 30 days of video storage.
What if the memory card is full?
This product supports video recording function, and the carliest video files are automatically overwritten when the memory card is full. In addition, our video is in standard MKV format and can be played barrier-free on the computer.
How often do solar camera products need to be recharged?
Solar panels typically designed by solar cameras can support a continuous month of wet weather when the sun can shine. If it's rainy for more than a month or frequently wakes up the device, it should take it off and use the USB power to recharge it. When USB charging or solar charging, the battery status can be seen in the app preview interface.
Documents / Resources
 |
Shenzhen S1 Smart PTZ Camera [pdf] User Guide 2AW9M-S1, 2AW9MS1, S1 Smart PTZ Camera, S1, Smart PTZ Camera, PTZ Camera, Camera |
References
- User Manual >
