ShenZhen Q36 Wireless Gaming Controller

Q36 Functional diagram

1. D-pad Button
2. X/Y/B/A Button
3. Reconnection/Power Button
4. -/ View Button
5. +/Menu Button
6. Type-C Charging Port
7. L/L2 Button
8. R/R2 Button
9. Reset Hole
10. Mode Switch
11. LED
12. Pair/Power Button

Press left joystick

Android / iOS / Windows

Android 9.0/iOS13.0/Win10 and above

Bluetooth connection (Joycon mode)

1. Flip the switch: Switch to S.
2. First use (Power-on pairing):
   • Press L2 + to boot and pair Joycon left controller;
     Press R2 + to boot and pair Joycon right controller, LED flash.
   • On the switch console, select System Settings Controllers and Sensors Change Grip/Order to enter the switch console matched page.
   • Joycon left handle connected successfully LED white steady;
     Joycon right handle connected successfully LED green on.
3. Use again (Reconnection):
   Press the button to power on, and automatically reconnect to the current mode controller.
4. Press the Pair button to power off the device.

PS4 mode

No touchpad function

Bluetooth connection

1. Flip the switch: Switch to P to enter the PS4 mode.
2. First use (Power-on pairing):
   • Using T YPE-C U SB connect the P S4 console, and the LED blink quickly.
   • Press the but ton to connect successfully, the LED is steady red.
3. Use again (Reconnection):
   • Press the button to power on and the LED will blink red slowly.
   • The LED is red when reconnection is successful.
4. Press the Pair button to power off the device.

Note: Press Pair to boot the pair, you can connect to a higher version of Android or iOS.

Firmware upgrade

• In the off state, press L + X + to connect the GamepadSpace-Q36 Bluetooth device of Android or Apple phone.
• Mobile App Market Download and install the Gamepad-Space App for firmware upgrade.

Charging / Sleep / Wake-up

When charging, the LED will blink slowly; When the battery is full, the LED will keep bright.

Sleep / Wake-up function:

• In pairing state: the controller will sleep if it’s not paired successfully within 2 minutes.
• Connect back state: The controller will sleep if it is not connect back within 1 minutes.
• Bluetooth is connected state: The controller will sleep if the controller is not used within 15 minutes.

Wake-up function:
Press to connect back when you need to wake-up it.

Gyro calibration
In the off state, lay the controller flat and press the

Electrical parameters

• Working voltage: DC3.7V
• Working current: < 30mA
• Sleep current: < 5uA
• Specification: DC5V/500mA
• Bluetooth transmission distance: <= 8M
• Battery capacity: 180mAh
• Standby time: 30 days (fully charged)

Product warning

FCC WARNING

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. Press and : D-pad left joystick FCC ID:2A3VP-Q36S

Frequently Asked Questions

How do I know if the device is successfully paired?

Successful pairing is indicated by the LED lights on the controllers or devices.

What should I do if the pairing process fails?

If pairing fails, restart the device and controller, then attempt pairing again following the instructions provided.

Documents / Resources

ShenZhen Q36 Wireless Gaming Controller [pdf] User Manual Q36S, Q36XSP, Q36 Wireless Gaming Controller, Q36, Wireless Gaming Controller, Gaming Controller, Controller

References

• User Manual