Q2 Small Camera
“
Specifications:
- Model: Q2
- Indicator Light: Blue
- Frequency Band: 2.4GHz
- App: V720
Product Usage Instructions:
Adding Device:
-
Step 1: Plug the device into the power
supply.Step 2: Press and hold the Reset key until the
blue indicator light starts flashing rapidly. -
Step 3: Turn on Bluetooth and open the V720
app.Step 4: Wait for the pop-up window to appear
when a new device is found, then click to bind the device. If no
pop-up appears, click the + icon in the app to add a device. -
Step 5: Select the Wi-Fi network and enter the
password (only 2.4GHz supported). -
Step 6: Wait for the device to be successfully
bound.
AP Mode:
-
Step 1: Repeat the steps for adding a
device. -
Step 2: Turn on Wi-Fi on your mobile phone and
connect to the Wi-Fi hotspot starting with Nax_. -
Step 3: Return to the V720 app, refresh the
drop-down list, and wait for the device to appear indicating
successful short-range mode connection.
Frequently Asked Questions (FAQ):
Q: What should I do if the blue indicator light does not flash
rapidly after resetting?
A: Make sure the device is properly plugged in and try resetting
again. If the issue persists, contact customer support.
Q: Can I use a 5GHz Wi-Fi network for configuration?
A: No, only the 2.4GHz frequency band is supported for
configuring the device.
“`
Step 2: Add device (Using model Q2 as an example)
1. As shown in (Picture 1): When the device is plugged into the power supply, the blue indicator light begins to flash slowly. Then, press and hold the Reset key to reset the device, and following this, the blue indicator light will start flashing rapidly.
2. As shown in (Picture 2): Turn on Bluetooth, then open the “V720” app. Wait for the pop-up window to appear when a new device is found, and click to bind the device. (If no new device pop-up window appears, please click the “+” icon in the upper right corner of the home page to add a device.)
The image shown here is just one of our products. For specific product you bought, please see the product interface page that came with the product.
Picture 1
Picture 2
4
3. As shown in (Picture 3) Select or enter the Wi-Fi network you want to configure and fill in the password. (Note: Only the 2.4GHz frequency band is supported.)
4. As shown in (Picture 4) Wait for the device to be bound successfully.
Picture 3
Picture 4
5
AP Mode
1. Repeat the steps from the first step to add a device. 2. As shown in (Picture 5): Turn on the Wi-Fi on your mobile phone and connect to the Wi-Fi hotspot starting with “Nax_”. 3. As shown in Picture 6: Return to the ‘V720’ app and refresh the drop-down list. When the device appears that means the short-range mode connection is successful.
Picture 5
Picture 6
6
Matters needing attention 1. This product can work within a temperature range of -10°C to 50°C (14 to 122). Please avoid using this product in environments with extreme temperatures, either too high or too low. 2. This product is a precision electronic product. Please do not use this product in environments that are excessively wet or where water may enter the product. 3. To better use this product, please avoid placing it near glass and other interfering objects, as this can cause the picture to be overly bright and may also affect the night vision. 4. Please ensure that this product is installed within the range of Wi-Fi signal coverage, and placed as far as possible from the microwave oven or other appliances that may affect the signal.
The image shown here is just one of our products. For specific product you bought, please see the product interface page that came with the product.
7
FCC Caution: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
8
Documents / Resources
 |
Shenzhen Q2 Small Camera [pdf] Instructions 2BON2-D7W, 2BON2D7W, Q2 Small Camera, Q2, Camera, Q2 Camera, Small Camera |