GW70-MQTT Zigbee2MQTT Dongle
“
Product Information
Technical Specifications
- Wireless Communication Frequency: 2.4GHz-2.48GHz
- Supported Protocols: Thread, Zigbee 3.0, Bluetooth 5.2 LE
- PORT config ESD protection: /dev/ttyUSB0
- Applicable Systems: Home Assistant-ZHA, Home
Assistant-Zigbee2Mqtt, OpenHAB - Communication Distance: 400 meters (Without obstruction)
- Signal Strength: 18.6 dbm (Instrument testing)
- Antenna Gain: 0 dbi
- Maximum Supported Device Number: 128
Usage Instructions
- Open the package, connect the antenna to the USB port, and then
insert it into a Computer / Raspberry Pi / HomeAssistant Green
etc. - Enter the corresponding system configuration (Home
Assistant/OpenHAB) product port (port: /dev/ttyUSB0). *For detailed
configuration procedures, please refer to the guidance documents of
the corresponding system. - After configuration is completed, the device can be connected
and used.
Supported Protocols: You can extend the network
range by using it as a router through re-flashing the firmware.
Zigbee2MQTT Dongle: Scan the QR code to learn
about the connection between this product and HomeAssistant.
FAQ
Q: How do I troubleshoot connectivity issues?
A: If you experience connectivity issues, try reorienting or
relocating the receiving antenna, increasing the separation between
devices, or consulting a professional for assistance.
Q: Can the device be used in portable exposure conditions?
A: Yes, the device has been evaluated to meet general RF
exposure requirements and can be used in portable exposure
conditions without restriction.
“`
Zigbee2MQTT Dongle
User manual
Zigbee2MQTT Dongle
Technical Specifications
Wireless Communication Frequency
Supported Protocols
PORT config ESD protection
Applicable systems
2.4GHz-2.48GHz
ThreadaZigbee 3.0a Bluetooth 5.2 LE /dev/ttyUSB0 Yes Home Assistant-ZHAa Home Assistant-Zigbee2Mqtta OpenHAB
Communication Distance
Signal strength (dbm)
400M(Without obstruction) 18.6(Instrument testing)
Antenna gain
0
(dbi)
Maximum
128
supported device
number
Usage Instructions
1.Open the package, connect the antenna to the USB port, and then insert it into a Computer / Raspberry Pi / HomeAssistant Green etc.
Zigbee2MQTT Dongle
2.Enter the corresponding system configuration (Home Assistant/OpenHAB) product port (port: /dev/ttyUSB0). *For detailed configuration procedures, please refer to the guidance documents of the corresponding system.
3.After configuration is completed, the device can be connected and used.
Supported protocols
*Of course, you can also extend the network range by using it as a router through re-flashing the firmware.
Zigbee2MQTT Dongle
Scan the QR code to learn about the connection between this product and HomeAssistant.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna. -Increase the separation between the equipment and
receiver. -Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected. -Consult the dealer or an experienced radio/
TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party.
FCC Radiation Exposure Statement:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Responsible for compliance could void the user’s authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Documents / Resources
 |
Shenzhen GW70-MQTT Zigbee2MQTT Dongle [pdf] User Manual 2BQUG-GW70-MQTT, 2BQUGGW70MQTT, GW70-MQTT Zigbee2MQTT Dongle, GW70-MQTT, Zigbee2MQTT Dongle, Dongle |