Shenzhen

Shenzhen Tianqiao Science Technology H62S Series Smart Switch-

H62S Series Smart Switch
Manual

Shenzhen Tianqiao Science Technology H62S Series Smart Switch-fig1

This user manual applies to:
• Wifi switch

Installation

westermo DDW 120 Wolverine Industrial Ethernet SHDSL Extender - warning1 Warning: Make sure power supply totally been cut off for the switch you are replacing.

  1. Remove your old switch from the junction box
  2. As shown in these diagrams below, insert wires into the corresponding terminal holes and fasten them.
  3. Take off-panel and fix switch with screws to the junction box in the wall.
    For Dimmer switch
    Dimmer switch
    CERTIFICATE: CE, ROHS
    INPUT: 100-240V-50/60HZ
    OUTPUT: 300W/gang
    Wireless protocoljlEEE: 2. 4GHz
    SIZE: 70*120*41mm
    Shenzhen Tianqiao Science Technology H62S Series Smart Switch-fig2

• Neutral switch
CERTIFICATE: CE, ROHS
INPUT: 100-240V-50/60HZ
OUTPUT: 500W/gang
Wireless protocoljlEEE: 2.4GHz
SIZE: 70*120*41mm

Shenzhen Tianqiao Science Technology H62S Series Smart Switch-fig3
• Non neutral switch
CERTIFICATE: CE, ROHS
INPUT: 100-240V-50/50HZ
OUTPUT: 150W/gang
Wireless protocoljlEEE: 2. 4GHz
SIZE: 70*120*41mm

Shenzhen Tianqiao Science Technology H62S Series Smart Switch-fig4

This user manual applies to:
• Wifi switch
westermo DDW 120 Wolverine Industrial Ethernet SHDSL Extender - warning1 Warning: Make sure power supply totally been cut off for the switch you are replacing.

  1. Remove your old switch from the junction box
  2. As shown in these diagrams below, insert wires into the corresponding terminal holes and fasten them.
  3. Take off-panel and fix switch with screws to the junction box in the wall.

For Dimmer switch
Dimmer switch
Model: TY-TI-WUSH62S-T1D
CERTIFICATE: CE, ROHS
INPUT: 100-240V-50/60HZ
OUTPUT: 300W
Wireless protocoljlEEE:
802. 11 Wen, 2. 4GHz
SIZE: 70’120’41mm
Shenzhen Tianqiao Science Technology H62S Series Smart Switch-fig5

For 1 gang switch
1 gang switch
Model: TY-TJ-WUSH62S-L1D
CERTIFICATE: CE, ROHS
INPUT: 100-240V-50/60HZ
OUTPUT: 1000W/gang
Wireless protocoljlEEE:
802. 11 b/g/n, 2. 4GHz
SIZE: 70*120*41mm

Shenzhen Tianqiao Science Technology H62S Series Smart Switch-fig6

For 1 gang 2 way switch

Shenzhen Tianqiao Science Technology H62S Series Smart Switch-fig7

Add switch to APP

  1. Download Smart Life APP from AppStore and register
  2. Preparations before getting started
    • For WiFi switch A wifi router is required, the wifi switch only supports a 2.4GHz WIFI network.
  3. Power up the switch, press and hold the button(for about 5 seconds) until the indicator blinking to enter pairing mode, then do the following steps for adding.

• For WiFi switch

  1. 0pen Smart Life APP, tap the icon
    Shenzhen Tianqiao Science Technology H62S Series Smart Switch-fig8
  2. Tap Electrical–Switch(Wl-Fl), + on the top right in the homepage. enter into Add Device
  3. Choose your local wifi and input wifi password
    Shenzhen Tianqiao Science Technology H62S Series Smart Switch-fig9
  4. Confirm the indicator is blinking rapidly.—(Long press any switch button for about 5 seconds then the indicator will blink)
    Shenzhen Tianqiao Science Technology H62S Series Smart Switch-fig10
  5. Wait for configuring successfully, then tap Complete and edit the name

FCC Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement
To comply with FCC RF exposure compliance requirements, this grant is applicable to only mobile configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Documents / Resources

Shenzhen Tianqiao Science Technology H62S Series Smart Switch [pdf] User Manual
TYTJWUSH62SL1D, 2A5CTTYTJWUSH62SL1D, H62S Series Smart Switch, H62S Series, Smart Switch

References

Leave a comment

Your email address will not be published. Required fields are marked *