Shelly Pro 2 DIN Rail Mountable 2 Circuit Smart Switch User Guide

Network Setup: Connect to a Wi-Fi network or LAN for remote access and control.
Output Configuration: Connect your devices to Out 1 and Out 2 for output functionality.

Resetting the Device: To reset the device, use the Reset button.
Control Switches: Utilize SW1 and SW2 for controlling specific functions of the device.

LAN Connectivity: For LAN connectivity, ensure proper connection to enable network features.

Safety information

For safe and proper use, read this guide, and any other documents accompanying this product. Keep them for future reference. Failure to follow the installation procedures can lead to malfunction, danger to health and life, violation of law, and/or refusal of legal and commercial guarantees (if any). Shelly Europe Ltd. is not responsible for any loss or damage in case of incorrect installation or improper operation of this device due to failure to follow the user and safety instructions in this guide.

This sign indicates safety information.
This sign indicates an important note.

WARNING!
- Risk of electric shock. Installation of the Device to the power grid must be performed carefully by a qualified electrician.
- Before installing the Device, turn the circuit breakers off. Use a suitable test device to make sure there is no voltage on the wires you want to connect. When you are sure that there is no voltage, proceed to the installation.
- Before making any changes to the connections, ensure there is no voltage present at the Device terminals.

CAUTION!
- Plug in or unplug the LAN cable only when the Device is powered off. The parts of the LAN cable that may be touched when plugging in or unplugging it, must not be metallic.
- Connect the Device only to a power grid and appliances that comply with all applicable regulations. A short circuit in the power grid or any appliance connected to the Device can cause fire, property damage, and electric shock.
- The Device may be connected to and control only electric circuits and appliances that comply with the applicable standards and safety norms.
- Do not connect the Device to appliances that exceed the specified maximum electric load.
- Connect the Device only in the way shown in these instructions. Any other method could cause damage and/or injury.
- The Device and the appliances connected to it, must be secured by a cable protection switch in accordance with EN60898-1 (trip- ping characteristic B or C, max. 16A rated current, min. 6 kA interrupting rating, energy limiting class 3).
- Do not use the Device if it shows any sign of damage or defect.
- Do not attempt to repair the Device yourself.
- The Device is intended only for indoor use.
- Keep the Device away from dirt and moisture.
- Do not allow children to play with the buttons/switches connected to the Device. Keep the devices (mobile phones, tablets, PCs) for remote control of Shelly away from children.

For inductive appliances that cause voltage spikes during switching on/off, such as electrical motors, fans, vacuum cleaners, and similar ones, an RC Snubber (0.1uF / 100 Q / 1/2 W / 600 VAC) should be connected in parallel with the appliance. The RC Snubber can be purchased at https://www.shelly.com/en/products/shop/rc-snubber.

Product description

Shelly Pro 2 (the Device) is a DIN rail mountable 2-circuit smart switch.
Enhanced with the second generation firmware flexibility and LAN connectivity, it provides professional integrators with many more options for end customer solutions.
The Device has an embedded web interface used to monitor, control, and adjust the Device. The web interface is accessible at http://192.168.33.1 when connected directly to the Device access point or at its IP address when you and the Device are connected to the same network.
The Device can access and interact with other smart devices or automation systems if they are in the same network infrastructure. Shelly Europe Ltd. provides APls for the devices, their integration, and cloud control. For more information, visit https://shelly-api-docs.shelly.cloud.
The Device comes with factory-installed firmware. To keep it updated and secure, Shelly Europe Ltd. provides the latest firmware updates free of charge. Access the updates through either the embedded web interface or the Shelly Smart Control mobile application. Installation of firmware updates is the user’s responsibility. Shelly Europe Ltd. shall not be liable for any lack of conformity of the Device caused by the failure of the user to install the available updates in a timely manner.

Wiring diagram

Legend

Device terminals

01, 02: Load circuit output terminals
11,12: Load circuit input terminals
SW1, SW2: Switch/button input terminals
L: Live terminal (110-240 V~)
N: Neutral terminal
LAN: Local Area Network RJ 45 connector Wires
L1(A): Load circuit 1 live (110-240 V~) wire
L2(B): Load circuit 2 live (110-240V~) wire
L3(C): Device power supply live (110-240 V~) wire

N: Neutral wire

Installation instructions

To connect the Device, we recommend using solid single-core wires or stranded wires with ferrules. The wires should have insulation with increased heat resistance, not less than PVC T105°C (221°F).
Do not use buttons or switches with built-in LED or neon glow lamps.

When connecting wires to the Device terminals, consider the specified conductor cross-section and stripped length. Do not connect multiple wires into a single terminal.
For security reasons, after you successfully connect the Device to the local Wi-Fi network, we recommend that you disable or password-protect the Device AP (Access Point).

Connect the N terminal to the Neutral wire and the L terminal to the Device power supply circuit breaker as shown in Fig. 1

Connect the first load circuit to the 01 terminal and the Neutral wire.
Connect the L1 terminal to the first load circuit breaker. Two different phases can be used for the load circuit and the Device power supply circuit.
Connect the second load circuit to the 02 terminal and the Neutral wire.

Connect the 12-terminal to the second load circuit breaker.
Connect the two switches/buttons to the SW1 and SW2 terminals and the Device power supply circuit breaker.

For inductive loads, connect an RC snubber in parallel to the load. For more details, see Fig. 2.

LED indications

Power (red): Red light indicator is on if power supply is connected. Wi-Fi (varies):
- The blue light indicator is on if in AP mode.
- The red light indicator is on if in STA mode and not connected to a Wi-Fi network.
- Yellow light indicator is on if in STA mode and connected to a Wi-Fi network. Not connected to Shelly Cloud or Shelly Cloud disabled.
- Green light indicator is on if in STA mode and connected to a Wi-Fi network and to the Shelly Cloud.
- The light indicator is flashing Red/Blue if the OTA update is in progress.
LAN (green): The Green light indicator is on if LAN is connected.
Out (red): Red light indicator is on if the Output switch is closed.

Reset button

Press and hold for 5 seconds for AP mode.
Press and hold for 10 seconds for a factory reset.

Specifications Physical

Size (HxWxD): 94x19x69 / 3.70×0.75×2.71
Weight: 76 g / 2.68 oz

Screw terminals max torque: 0.4 Nm / 3.5 lbin
Conductor cross section: 0.5 to 2.5 mm / 20 to 14 AWG (green connectors 0.5 to 1.5 mm / 20 to 16 AWG (blue connectors)
Conductor stripped length: 6 to 7 mm / 0.24 to 0.28 in (green connectors 5 to 6 mm / 0.20 to 0.24 in (blue connectors)

Mounting: DIN rail
Shell material: Plastic
Shell color: Gray

Environmental

Ambient working temperature: -20°C to 40°C / -5°F to 105°F
Humidity: 30% to 70% RH

Max. altitude: 2000 m / 6562 ft

Electrical

Power supply: 110-240 V~ 50/60 Hz

Power consumption: < 3 W
Output circuits ratings
Max. switching voltage: 240 V~

Max. switching current: 16 A per channel, 25 A total

Sensors, meters
Internal-temperature sensor: Yes

Radio Wi-Fi

Protocol: 802.11 b/g/n
RF band: 2400 – 2495 MHz
Max. RF power: < 20 dBm

Range: Up to 50 m / 164 ft outdoors, up to 30 m / 98 ft indoors (depending on local conditions)

Bluetooth

Protocol: 4.2

RF band: 2402 – 2480MHz
Max. RF power: <4 dBm
Range: Up to 30 m / 98 ft outdoors, up to 10 m / 33 ft indoors (depending on local conditions)

Microcontroller unit

CPU: ESP32-D0WDQ6
Flash: 8 MB

Firmware capabilities
Schedules: 20
Webhooks (URL actions): 20 with 5 URLs per hook

Wi-Fi range extender: Yes
BLE Gateway Yes
Scripting: Yes

MQTT: Yes
Encryption: Yes

Shelly Cloud inclusion

The Device can be monitored, controlled, and set up through our Shelly Cloud home automation service. You can use the service through either our Android, iOS, or Harmony OS mobile application or through any internet browser at
https://control.shelly.cloud/.
If you choose to use the Device with the application and Shelly Cloud service, you can find instructions on how to connect the Device to the Cloud and control it from the Shelly app in the application guide: https://shelly.link/app-guide.
The Shelly mobile application and Shelly Cloud service are not conditions for the Device to function properly. This Device can be used stand-alone or with various other home automation platforms.

Troubleshooting
In case you encounter problems with the installation or operation of the Device, check its knowledge base page: https://shelly.link/pro_2

Declaration of Conformity
Hereby, Shelly Europe Ltd. declares that the radio equipment type Shelly Pro 2 is in compliance with Directive 2014/53/EU, 2014/35/EU, 2014/30/EU, 2011/65/EU. The full text of the EU declaration of conformity is available at the following internet address: https://shelly.link/Pro2_DoC

Disposal and recycling

This refers to the waste of electrical and electronic equipment. It is applicable in the EU, the US and other countries to collect waste separately.
This symbol on the Device or in the accompanying literature indicates that it should not be disposed of in the daily waste.
The Device must be recycled to avoid possible damage to the environment or human health from uncontrolled waste disposal and to promote the reuse of materials and resources.

It is your responsibility to dispose of the Device separately from general household waste when it is no longer usable.

Manufacturer: Shelly Europe Ltd
Address: 103 Cherni Vrah Blvd., 1407 Sofia, Bulgaria

Tel.: +359 2 988 7435
E-mail: support@shelly.cloud
Official website: https://www.shelly.com

Changes in contact information are published by the Manufacturer on the official website. All rights to the trademark Shelly® and other intellectual rights associ- ated with this Device belong to Shelly Europe Ltd.

FAQ

Q: How do I reset the device?
A: Press the Reset button to initiate a reset of the device.

Q: Can I connect multiple devices to the outputs simultaneously?
A: Yes, you can connect multiple devices to Out 1 and Out 2 for simultaneous output.

Documents / Resources

Shelly Pro 2 DIN Rail Mountable 2 Circuit Smart Switch [pdf] User Guide
Pro 2 DIN Rail Mountable 2 Circuit Smart Switch, Pro 2 DIN, Rail Mountable 2 Circuit Smart Switch, Circuit Smart Switch, Smart Switch, Switch

References

User Manual

Shelly Pro 2 DIN Rail Mountable 2 Circuit Smart Switch

Specifications

Product Usage Instructions