SERENELIFE SLSUPB872 ISUP Rising Flow Inflatable Paddleboard
Specifications
- Product Name: SLSUPB872 Rising Flow Inflatable Paddleboard iSUP
- Construction: Drop Stitch, Reinforced Engineered PVC
- Dimensions: 126.0” x 33.0” x 6.0” (Inflated)
Product Usage Instructions
Introduction
Please read this entire manual carefully before inflating and using the product. Familiarize yourself with the features of the SUP and ask for professional training if you are inexperienced in handling this type of board. Follow proper safety procedures and waterway rules for SUP usage.
What’s Included
- Tie down Bungee Cords
- Coiled Ankle Cuff Safety Leash
- Carrying Handle
- Air Valve
- Storage / Carry Bag
- Patch Repair Accessory Kit Fins
- Leash Plug
- Oar Paddle
- Manual Air Pump (SLSUPST15)
- SUP Seat (*sold separately)
Getting Started
Inflation Instructions
- Lay the SUP board flat with the top side facing up.
- Push the air valve down while twisting it slightly to lock it in the UP position.
Important: Use only the provided pump for safe and proper inflation. Using any other pump may damage the SUP board.
Deflating Instructions
- Press the valve down and turn it to the DOWN position to release the air.
- Roll the board from the nose end toward the valve to push out excess air.
- Secure the valve cap once deflated.
SUP Board Air Pump
Your SUP Board comes with a high-pressure manual air pump. It provides low-volume but high-pressure inflation for optimal performance. Remember to add oil/grease to the gasket and tube periodically and check the air filter.
Reminder: Only use the provided pump to inflate the SUP board to avoid improper inflation or damage.
Installing the Fin
- Ensure the center fin box is clean and free of debris.
- Put fin base into fin box from the wide inlet.
- Push the fin down and secure it by turning the screw.
Repair Kit
- Deflate the board completely, lay it flat, and allow it to dry.
- Clean the repair area with alcohol.
- Cut a patch larger than the tear or rip on all sides.
- Apply three coats of adhesive (not included in the kit) to repair the board.
FAQ
- Q: Is it necessary to add oil/grease to the gasket and tube of the air pump?
- A: Yes, it is recommended to add a few drops of oil/grease to ensure proper functioning of the air pump.
- Q: How should I store my inflatable paddleboard when not in use?
- A: When not in use, deflate the paddleboard, clean and dry it properly, and store it in a cool, dry place away from direct sunlight and heat sources.
FOR YOUR SAFETY
- Check your board & equipment before going into the water.
- Try to avoid going out on the water alone.
- Always have a means of communication while on the water.
- Check weather conditions and tides before heading out.
- Avoid paddling when winds are blowing away from shore.
- Be aware of tides and water flow, and how they may affect your travel time.
- Wear a wetsuit or dry suit as needed.
- Always wear a life jacket or a flotation device.
- Always wear your board leash.
- Take a first aid course, and always carry first aid equipment.
- Do not go out on the water if you cannot swim.
- Avoid going on the water if you have been drinking or are under the influence of drugs.
California Prop 65 Warning
WARNING
This product contains Toluene which is known to the state of California to cause cancer birth defects and other reproductive harm. Do not ingest.
For more info go to: www.P65warnings.ca.gov
Features
- Stand-Up Paddle-Board (SUP)
- Single Person Floating & Inflatable Platform Base
- Water-Ready: Includes Everything Needed to Paddle
- Stable & Universal Board Design for Children, Teens & Adults
- Marine Grade Water-Resistant and Corrosion-Resistant Construction
- Portable Paddle-Board Deflates & Roll-Ups for Easy Storage and Transport
- Features (3) Bottom Panel Fins for Speed, Steering and Maneuverability
- Lightweight & Hassle-Free Setup for Quick Water Fun
- Includes GoPro Holder on a Paddleboard
- Used to Paddle at the Lake, River or Ocean
Technical Specs
- Water Fun for Ages: 10+
- Recommended Air Pressure Inflation: 13 PSI (0.89 Bar)
- Highest Working Pressure: 15 PSI
- Max. Weight Capacity: 330 lbs.
- Construction Materials: Drop Stitch, Reinforced Engineered PVC
- Paddle-Board Dimensions (L x W x H): 126.0’’ x 33.0’’ x 6.0’’ (-Inflated)
INTRODUCTION
IMPORTANT! PLEASE READ THIS MANUAL CAREFULLY, AND IN ITS ENTIRETY, BEFORE INFLATING, ASSEMBLING OR USING YOUR RISING FLOW PADDLEBOARD ISUP.
- Please read this entire manual carefully before inflating and using the product
- Familiarize yourself with the features of the SUP and ask for professional training if you are inexperienced in handling this type of board. For your full enjoyment it is important to follow proper safety procedures and rules of the waterway that apply to all SUPs. Always check the local weather conditions before taking the SUP out.
- Do not let yourself get caught out by currents in tidal inlets, open seas, small channels or shallow water regions.
What’s in the Box
- SUP Paddle-Board
- High-quality Aluminum Oar Paddle
- High-quality Manual Air Pump
- Coiled Ankle Cuff Safety Leash
- Patch Repair Accessory Kit
- Storage / Carry Bag
- Waterproof Mobile Phone Case
WHAT’S WHAT?
GETTING STARTED
Inflation Instructions
INFLATING THE SUP BOARD
- Preparation: Lay the SUP board flat with the top side facing up.
- Valve Position: Push the air valve down while twisting it slightly to lock it in the UP position.
This setting allows air to flow only into the SUP board.
(Note: When the valve is DOWN, air flows both in and out of the board.) - Attaching the Pump: Connect the pump to the air valve by twisting it clockwise until it’s secure.
- Pumping Air: Start inflating by maintaining proper posture and steady leverage while pumping.
Use only the provided manual air pump.
Warning: DO NOT use an air compressor, as it may damage the paddleboard. - Recommended PSI: Inflate to a recommended level of 13 PSI. The maximum working pressure is 15 PSI. Warning: DO NOT OVER-INFLATE. DO NOT EXCEED 15 PSI.
- Detaching the Pump: Once inflated, remove the pump by twisting counter-clockwise.
- Sealing the Valve: Screw the air valve cap securely onto the valve.
Important: Use only the provided pump to ensure safe and proper inflation. Using any other pump may damage the SUP board.
DEFLATING THE SUP BOARD
- Press the valve down and turn it to the DOWN position to release the air.
- Roll the board from the nose end toward the valve to push out excess air.
- Once deflated, secure the valve cap.
SUP Board Air Pump
Your SUP Board comes with a high-pressure manual air pump. This pump provides low-volume but high-pressure inflation, ensuring optimal performance and extending the life of your SUP board. The pump is pre-lubricated, but it’s recommended to add a few drops of oil/grease to the gasket and tube periodically and check the air filter.
Reminder
Only use the provided pump to inflate the SUP board. Using any other pump can lead to improper inflation or damage to the board.
INSTALLING THE FIN
- Make sure the center fin box is clean and free of debris.
- Put fin base into fin box from the wide inlet.
- Push the fin down
- The fin base will slide to the end of box at the same time.
- Turn the screw to secure fin firmly.
THE PADDLE
Your board paddle comes in three pieces. To assemble the paddle, press the button while sliding the pieces together until they click into place. The top section of the paddle is adjustable. To find the ideal height, start by adjusting the paddle to be 6 inches taller than your height. From there, adjust the top section up or down until the length feels comfortable. A longer paddle is better suited for a smooth, easy paddling motion, while a shorter paddle is ideal for performance or competition riding.
REPAIR KIT
If your board needs repair, use the patches in the repair kit and follow these steps
- Deflate the board completely, lay it flat, and allow it to dry.
- Cut a patch that is 2 inches larger than the tear or rip on all sides.
- Clean the repair area with alcohol.
- Apply three coats of adhesive (not included in the kit) to both the patch and the board, waiting 5 minutes between each coat.
- Place the patch over the tear or rip. The adhesive will bond quickly, so ensure precise positioning. Use a roller to make the patch lie flat and even.
- Wait 24 hours before re-inflating the board.
STORAGE
Having an inflatable SUP board makes portability and storage easy. Here are some suggestions for storing or traveling with your SUP board
- Avoid storing your SUP board in direct sunlight.
- If you need to store the board inflated between uses, attach the pump to check that it maintains the correct air pressure.
- When storing the board deflated, avoid rolling it too tightly.
- If fins become bent, place them in boiling water and use heat (such as a hairdryer) to bend them back into position.
Register Product
Thank you for choosing SereneLife.
By registering your product, you ensure that you receive the full benefits of our exclusive warranty and personalized customer support. Complete the form to access expert support and to keep your SereneLife purchase in perfect condition.
Serenelifehome.com/pages/register
Questions or Comments
We are here to help!
- Phone: 1.718.535.1800
- Serenelifehome.com/ContactUs
Documents / Resources
 |
SERENELIFE SLSUPB872 ISUP Rising Flow Inflatable Paddleboard [pdf] User Guide SLSUPB872, SLSUPB872 ISUP Rising Flow Inflatable Paddleboard, ISUP Rising Flow Inflatable Paddleboard, Rising Flow Inflatable Paddleboard, Flow Inflatable Paddleboard, Inflatable Paddleboard, Paddleboard |
