SenseCAP MET M2 Multi Platform Gateway
Specifications:
- Model: SenseCAP M2
- Optional accessories for Wx9xx series transmitters
- Manufacturer: COMET SYSTEM, s.r.o.
- Address: Bezrucova 2901 756 61 Roznov pod Radhostem, Czech Republic
- Product Type: Gateway
Product Description and Use
The SenseCAP M2 is a gateway designed as an optional accessory for Wx9xx series transmitters. It is used to connect the transmitters to the COMET Cloud for data transmission and monitoring.
Installation and Configuration:
- Configure the gateway via WiFi following the instructions in the original device manual.
- To register the gateway to the COMET Cloud, go to Administration > LoRa Gateways menu.
- Add the gateway to the list by entering its Gateway EUI identifier (found on the label at the bottom of the device).
- You can provide a name and location for the gateway on the map for easier identification.
- Connect the gateway to power and ensure it is connected as per the recommended setup.
Recommended Gateway Connection:
To maintain cybersecurity, it is advised to connect the gateway to a separate VLAN. Follow the image below for the correct connection. Once connected, the gateway status should change to ONLINE in the cloud.
- This tutorial will guide you to use the SenseCAP M2 Multi Platform gateway to connect to SenseCAP LoRaWAN® sensors.
Gateway Network Configuration
There are two ways to connect to the Internet. Choose the one that works for you.
Connect to Ethernet Cable
Connect the Ethernet cable to the device, and the indicator on the top will show solid green if the gateway is successfully connected to the internet.
Connect to WIFI via Luci
There are two ways for users to login Luci configuration page.
Access via router
- Step 1: Connect your device to an Ethernet cable, and connect your PC to the same router.
Note: Your PC and device should be connected to the same router/network.
- Step 2: Get IP Address of your device
Check the IP Address of your device on your router admin page. - Step 3: Get your device Username and Password
You can find the Username and Password on your device label,
- Step 4: Log into Luci
Input the IP Address of your device in a browser to enter the Luci page. Then input your device username and password to login.
Access via the device AP hotspot
- Step 1: Turn on the device AP hotspot.
Press the button for 5 seconds until the blue indicator flashes slowly to enter the configuration mode. - Step 2: Connect to the AP hotspot.
AP hotspot name is SenseCAP—XXXXXX (6-figure MAC address),default password is 12345678; connect your computer to this AP hotspot.
- Step 3: Set your device Username and Password
You can find the IJsername and Password on your device label.
- Step 4: Log in to the Local Console
- Input the IP Address (192.168,168.1) in your browser to enter the Local
- Console. Then input your device username and password, and click the Login button.
- Step 5: Connect to a WIFI
Click on Network – Wireless
- Click on the Scan button to scan the WIFI.
- Select your WI-FI to join the network.
- Submit the Wi-Fi password, and then click “Submit” and “Save”
The indicator on the top will show solid green if the gateway is successfully connected to the WIFI
POE connection
SenseCAP M2 supports POE ( Power on Ethernet) and is compatible with IEEE 8 02 . 3 af standard.
Note:
You will need to have an extra POE switch that provides 40V-57V DC power as a PSE (Power Sourcing Equipment) if your modem/router does not support PoE.
Checking the Gateway Connection Status
After powering on the gateway, there are two ways for you tocheck the gateway working status::
LED Indicator
SenseCAP Mate APP
In the SenseCAP Mate App, “Online status” indicates “Online” when the gateway is connected to the network and can receive and transfer sensor data. Please refer to the next chapter for obtaining the SenseCAP App.
Bind the gateway
SenseCAP Mate APP supports device configuration and remote management.
- Step 1: Download the SenseCAP Mate APP
- SenseCAP Mate APP for iOS on App Store
- SenseCAP Mate APP for Android on the Google Play Store
- You can also download App from App Center
- Download the SenseCAP Mate App
- Step 2: Log in to the APP
If it is your first time to use the SenseCAP platform, please register an account first.
Note: Please select Global of Server Location.
Step 3: Add device
Click the + in the upper right corner and select Add device Then, scan the QR code on your gateway label.
- Set up your device name and location. Then confirm your settings.
- After successful binding, you will see your gateway in the Device directory.
Connect the SenseCAP Sensors
Step 1: Add device
Click the + in the upper right corner and select Add device Then scan the QR code on your gateway label.
Step 2: Select the frequency plan
Click on “Settings”, set the platform and frequency, and the frequency should match your gateway frequency.
eg: If your gateway is US915 version, then you need to set your sensor to IJS915 frequency.
- Note: SenseCAP M2 Multi-Platform Gateway can ‘t connect to the Helium network.
- For more configurations about SenseCAP sensors, please refer to: SenseCAP Sensors
SenseCAP Portal and Mate APP
- SenseCAP Mate APP and SenseCAP Portal can be used to check your
device status and device management. - SenseCAP Mate APP for iOS on App Store
- SenseCAP Mate APP for Android on the Google Play Store
- SenseCAP Portal
Gateway Info
Check the gateway info on the SenseCAP Portal and the SenseCAP Mate APP
SenseCAP Mate APP
Sensor data
Check the sensor data on the SenseCAP Portal and SenseCAP Mate APP
SenseCAP Portal
SenseCAP Mate APP
FAQs
Q: What should I do if I need to reset the gateway to factory settings?
A: Resetting the gateway will result in the loss of all presets. To reset, follow the instructions provided in the user manual carefully.
Q: How do I know if my gateway is properly connected?
A: Check the gateway list in the COMET Cloud; if the status changes to ONLINE and the indicator on the front surface turns permanently green, your gateway is connected correctly.
Documents / Resources
 |
MET SenseCAP M2 Multi Platform Gateway [pdf] User Guide SenseCAP M2 Multi Platform Gateway, SenseCAP M2, Multi Platform Gateway, Platform Gateway, Gateway |