Seeedstudio ODYSSEY – X86J4105 User Manual

Package Contents

• ODYSSEY – X86J4105
• User Manual
• International Power Adapter
• SATA Cable
• Antenna x2
• RTC Battery
• Heat Sink (Assembled)
• Cooling Fan (Assembled) (Included in EMMC version)

Specifications

Processor	Intel® Celeron® J4105 Frequency: 1.5 – 2.5GHz
Coprocessor	Microchip® ATSAMD21G18 32-Bit Arm® Cortex® M0+
Graphics	Intel® UHD Graphics 600 Frequency: 250 – 750MHz
Memory	LPDDR4 8GB
Storage	64GB eMMC V5.1
Wireless	Wi-Fi 802.11 a/b/g/n/ac @ 2.4/5 GHz HT160 Bluetooth® 5.0
Networking	Intel® I211AT PCIe Gigabit LAN
Audio	Microphone + headphone Combo Connector
Headers	28-pin header from SAMD21G18 40-pin header compatible with Raspberry Pi
USB	USB 2.0 Type-A x2 USB 3.1 Type-A x1 USB 3.1 Type-C x1
Video Interfaces	HDMI2.0a: Up to 4096×2160 @ 60Hz 24bpp DP1.2a: Up to 4096×2160 @ 60Hz 24bpp
Expansion Slots	M.2(Key B, 2242/2280): SATA III, USB2.0, UIM M.2 (Key M, 2242/2280): PCIe 2.0 ×4 Micro SD card Socket SIM Card Socket SATA III
RTC	JST 1.0 CR2032 3V
TPM	Built-in TPM (2.0)
Power	DC Jack 5.5/2.1mm or Type-C PD DC Jack input: 12-19V DC Type-C input: USB PD
Dimensions	110x110mm
Certifications	FCC, CE

Quick Start with ODYSSEY – X86J4105

Before you Start
Make sure you have the following:

1. An external monitor
   
                    Figure 1
2. A keyboard and a mouse
   
         Figure 2
3. An HDMI Cable
   
                Figure 3

Attaching External Storage

If you have bought the 64GB EMMC storage version of the ODYSSEY – X86J4105, you can skip this step. However, if you need more storage for your needs, feel free to follow this step. There are four methods of adding storage to ODYSSEY – X86J4105

1. Through M.2 PCIE Connector
2. Through M.2 SATA connector
3. Through SATA Connector
4. Through Micro SD Card Slot

Note: Only three storage types support to install an operating system inside (M.2 SATA, M.2 PCIE and SATA), and the Micro SD Card can only be used as external storage.

Connecting Antennas

Insert the two antennas into the two sockets on the ODYSSEY – X86J4105

Note: One antenna is for Wi-Fi and Bluetooth whereas the second antenna is for strong 5G connectivity

Connecting to a display

Powering up

1. There are two ways to power up your ODYSSEY – X86J4105
   
                                     Method 1
   Use the 12V/2A power adapter (provided)
   
   Method 2
   Use a USB Type-C Cable (Supports DP)
   
2. Press the power button and you will notice the blue power LED turn on
   
3. Wait a few seconds until it boots into the operating system.
   

Installing an Operating System

ODYSSEY – X86J4105 supports both Windows and Linux operating systems. If you have bought the non EMMC version, you could attach an external storage by following the previous steps and install your desired operating system by creating a bootable USB drive. Also, if you have bought the EMMC version with windows pre-installed, you could additionally install Linux according to your requirements.

Step 1

Connect your bootable USB drive into one of the USB ports on the ODYSSEY – X86J4105

Step 2

Press the power button and keep pressing F7 key on the keyboard until you see the Boot Manager screen.

Step 3

Select the connected USB Drive as the boot drive and press enter

Step 4

Then follow the instructions on the installation screen to complete installing your desired operating system.

Adding 4G Cellular Connectivity

Step 1

Insert a standard SIM Card to the bottom layer of the slot

Step 2

Insert a PCIE 4G module

Note: This module is a must have if you want to use the connected SIM card.

Pinout diagram

FAQ

How can I access the BIOS setup?
Press the Power Button and keep pressing DEL key until you see the BIOS Setup.

Arduino IDE doesn’t recognize the onboard microcontroller
Add a jumper wire between pins 3 and 4 of UART pins on the 28-pin header to reset the AMSAMDG21.

I cannot connect to Wi-Fi and Bluetooth
Check BIOS settings and enable Wi-Fi and Bluetooth from BIOS.

ODYSSEY – X86J4105 doesn’t power up
Make sure you use the 12V/2A power adapter provided in the box and check the connection.

If you have any further questions, please visit forum.seeedstudio.com or send an email to techsupport@seeed.cc

 

Read More About This Manual & Download PDF:

Documents / Resources

Seeedstudio ODYSSEY - X86J4105 [pdf] User Manual ODYSSEY - X86J4105

References

• User Manual