SECURITY BRANDS 27-210 EDGE E1 Smart Keypad with Intercom Access Control System User Guide

QUICK START GUIDE

Model 27-210, 27-21

Unpack the box and make sure you have all items shown here. (Screwdriver not shown.)
Unlock and open the front panel of the unit for mounting, wiring, and setup.

Mount unit to pedestal using included mounting hardware.
(This step may be completed later.)

WARNING SECURITY BRANDS 27 210 EDGE E1 Smart Keypad with Intercom Access Control System - warning

AUTOMATIC GATES CAN CAUSE SERIOUS INJURY OR DEATH!

ALWAYS CHECK THAT THE GATE PATH IS CLEAR BEFORE OPERATING!

REVERSING OR OTHER SAFETY DEVICES SHOULD ALWAYS BE USED!

CAUTION

Use all four carriage bolts when mounting the unit to a pedestal.
Leave the antenna in place.
Seal all openings created in the enclosure.
Failure to follow these instructions can damage the unit and/or cause it not to function correctly!

What’s what?
All important components labeled
Model 27-210 is shown

The unit is shown with the front panel open.
Wiring/cabling not shown for clarity

4. Connect wires.
Feed wires through the back of the unit, and connect as shown using included screwdriver.
Excessive force can damage the unit!

Additional wiring diagrams can be found on Pages 5 and 6.

CAUTION

If the included 12-V AC/DC adapter will not be used, please go to Page 4 and follow the procedure, Using a Third-Party Power Source.
Do not exceed 24 VAC/DC! Failure to choose a compatible power source can damage the unit!

Using a Third-Party Power Source (Optional)

IMPORTANT
If you would like to use a third-party
power source such as solar, verify that it
conforms to the following specs:
Input
12–24 VAC/DC no more than 10% beyond this rangeCurrent Draw
less than 111 mA @ 12 VDC
less than 60 mA @ 24 VDC

4a Connect wires to the unit as shown in Step 4.
4b Connect wires to your power source, making sure you connect positive to positive and negative to negative.

CAUTION
Double-check that you have wired from positive on the Edge unit to positive on your power source and negative on the Edge unit to negative on your power source.
Reverse polarity can damage the unit!

5. The close front panel of the unit and lock it.

SECURITY BRANDS 27 210 EDGE E1 Smart Keypad with Intercom Access Control System - warning

STOP

Before going forward, double-check all wiring and make sure the unit has power!
Wiring diagrams for connecting to accessory devices can be found on Pages 5 and 6.
For connecting accessories not mentioned, please contact Technical Support.
Make sure the gate or door path is clear before completing Step 7!

6. Add Access Code to Relay A.
(To add multiple codes, enter each of them before pressing the pound key.)

NOTE: The green arrow indicates a “good” tone on the Edge unit. By default, the following codes are reserved and cannot be used: 1251, 1273, 1366, 1381, 1387, 1678, 1752, and 1985.

7. Make sure the gate or door path is clear; then enter the access code on the keypad, and the conﬁrm gate or door opens.
INSTALLATION COMPLETE!

Jump to Page 7 to continue programming and download the Edge Smart Keypad app.

A Event Inputs
Wiring for accessories such as a request-to-exit device

B Digital Inputs
Wiring to various accessories

C Wiegand Device
Wiring for a Wiegand device

If mounting a Wiegand card reader to the Edge unit front panel, remove the existing cover plate and hex nuts to reveal the mounting holes and wiring passthrough hole.

CAUTION
Disconnect power to the Edge unit before connecting Wiegand devices.
Failure to disconnect power can damage the unit!

Downloading the Edge Smart Keypad App for iOS/Android

The Edge Smart Keypad app is for ADMINISTRATOR USE ONLY and is not intended for users.

a Grab your smartphone or tablet. (These steps are optional. The unit can be fully programmed from the keypad.)

b Navigate to your app store, and search for “edge smart keypad.”

c Find the Edge Smart Keypad app by Security Brands, Inc. and download it.

Edge Smart Keypad
Security Brands, Inc.

SECURITY BRANDS 27 210 EDGE E1 Smart Keypad with Intercom Access Control System - help NEED HELP

You can find plenty of useful resources online to help you get your new Edge unit up and running quickly and easily.
Go to securitybrandsinc.com/edge/
If you need further assistance, please call
Technical Support at 972-474-6390.

D Pairing Edge Unit

Connect your mobile device to your Edge unit for use with the app.
The app is available for administrators who want to use it. Nearly all functionality is available through direct programming via the keypad.

IMPORTANT! Make sure your Edge unit is powered on and that Bluetooth is enabled on your mobile device or pairing will not work.

Step 1 – Grab your mobile device and open the Edge Smart Keypad app.
If you do not have the app, follow the steps on this page for downloading it.

Step 2 – Fill out your account information and tap the “Sign Up” button.
If you have already created an account, you will log in instead.

Step 3 – On the Paired Keypads screen, tap the “Add Keypad” button.

Step 4 – On the Add Keypad screen, tap the Edge unit you want to pair.
If you do not see any Edge units listed, make sure your Edge unit is powered on and is in Bluetooth range.

Step 5 – Complete the procedure shown on your mobile device. These steps will be completed using the PIN pad on your Edge unit. Step 6 – Enter the Master Code (default is 1251) on your mobile device.

Step 7 – Enter the code shown on your mobile device at the Edge unit. This step must be completed within the time duration displayed.

Step 8 – Change your Master Code if you like.
This step is recommended, but optional, and can be done at a later time.

Your new Edge unit is now be paired and will appear on the Paired Keypads screen. Tapping on the Edge unit on this screen will give you access to relay control and full access control management of the Edge unit from within the app.

For more information and guidance, please go to securitybrandsinc.com/edge/ or call Technical Support at 972-474-6390 for assistance.

E1 Direct Programming / Unit Configuration

Change Master Code
(Highly recommended for security purposes)

Change Sleep Code

The green arrow indicates a “good” tone on the unit.
Always wait for a good tone before moving on.

By default, these codes are unavailable for use: 1251, 1273, 1366, 1381, 1387, 1678, 1752, 1985.

FIND MORE

For all programming not shown here, as well as reset procedures and the Edge
Smart Keypad app user guide, please visit our Edge start page:
securitybrandsinc.com/edge/

Programming Sub Modes

Add Access Code(s) to Relay A

Delete Code (Non-Wiegand)
Change Master Code
– 3 Add Latch Code to Relay B
4 – 4 Change Sleep Code
4 – 5 Change Code Length (Non-Wiegand)
4 – 6 Change Relay Trigger Time
4 – 7 Enable/Disable Timers and Schedules
4 – 8 Enable/Disable “3 Strikes, You’re Out”
4 – 9 Configure Event Input 1

Add Latch Code to Relay A
Configure Wiegand Inputs
Add Access Code(s) to Relay B

Add Limited-Use Code
Delete All Codes and Timers

Things to Know

The Star Key (*)
If a mistake is made, pressing the star key deletes your entry. Two beeps will sound.

The Pound Key (#)
The pound key is good for one thing and one thing only: exiting the programming mode.

E2 Direct Programming / Unit Configuration

The green arrow indicates a “good” tone on the unit. Always wait for a good tone before moving on.

E3 Direct Programming / Unit Configuration

Toggle Silent Mode
(Toggles Silent Mode, which mutes all audible-tone feedback on the unit)

Configure Event Input 1
(Allows an external device to affect keypad operation or trigger a relay. To configure additional inputs, use the Edge Smart Keypad app.)

Mode 1 – Remote Open Mode
Triggers either Relay A or Relay B when event input state changes from normally open (N/O) to normally closed (N/C).

Mode 2 – Log Mode
Makes log entry of event input state when event input state changes from normally open (N/O) to normally closed (N/C).

Mode 3 – Remote Open and Log Mode
Combines Modes 1 and 2.

Mode 4 – Arming Circuit Mode
Enables either Relay A or Relay B when event input state changes from normally open (N/O) to normally closed (N/C). Otherwise, the selected relay is disabled.

Mode 5 – Remote Operation Mode
Triggers or latches either Relay A or Relay B when event input state changes from normally closed (N/C) to normally open (N/O).

Mode 0 – Event Input 1 Disabled

Modes 1, 3, and 4

E4 Direct Programming / Unit Configuration

Configure Event Input 1 (continued)
(Allows an external device to affect keypad operation or trigger a relay. To configure additional inputs, use the Edge Smart Keypad app.)

E5 Direct Programming / Unit Configuration

Configure Wiegand Input
(Allows enabling or disabling of a Wiegand input and configuration of the Wiegand device type. For the tag reader type, use the Edge Smart Keypad app.)