TIMERS V8.0, V9.0 Multi Functional Timer Relay
پيداوار جي استعمال جون هدايتون
- Description of Multi-functional Timer Relay:
- The multi-functional timer relay is designed to provide various timing functions based on user requirements. It can operate within a specified voltage range and offers different output types, depending on the model.
- Compare Timer Versions:
- The Version V9 of the timer relay offers more accurate frequency clock with just +/- 2sec per day fluctuation and software correction compared to Version V8, which has +/- 2% fluctuation. Additionally, V9 PCB is conformal coated for extra protection.
- Timer’s Wiring Diagram:
- Follow the appropriate wiring diagram based on the output type of the timer (Positive or Sink) to ensure proper connection and operation. Be cautious when connecting the timer to a programmer to avoid overload or damage to power sources.
- Understanding Timer Delay Relay Function:
- The timer delay relay functions provide control over output power based on specified events. Refer to the manual for detailed explanations of timing functions and terminology used in the circuit design. Understand how to initiate and trigger the timer for desired operation.
“`
TIMERS.SHOP
Multi-functional Timer relay. (Version V8.0 and V9.0)
استعمال ڪندڙ دستي
V3.5b 2025/10/19
!!! خبردار !!!
اصل پرچون ڪندڙ کي شيءِ واپس نه ڪريو. شيءِ يا شيءِ جي ترسيل ۾ ڪنهن به مسئلي لاءِ سپورٽ سان رابطو ڪريو.
ٽائمرس شاپ@gmail.com
http://timers.shop
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 2
ملٽي فنڪشنل ٽائمر رلي وضاحت
ملٽي فنڪشنل ٽائمر ڊيلي ماڊيول هڪ انقلابي سرڪٽ آهي جنهن ۾ ڪيترائي عام طور تي استعمال ٿيندڙ ٽائمر ڊيلي افعال آهن. اهو شوق کان وٺي صنعتي ڪنٽرول تائين ڪيترن ئي ايپليڪيشنن لاءِ بهترين آهي. ٽائمر ۾ ٽيهه کان وڌيڪ مختلف ٽائيمنگ افعال آهن جن ۾ ان پٽ وول جي استعمال سان انهن کي متحرڪ ڪرڻ جي اختياري صلاحيت آهي.tagٽرگر تار ڏانهن e. خشڪ رابطا پڻ استعمال ڪري سگھجن ٿا. ٽائمر کي سرڪٽ ۾ بجلي جي دير ڪرڻ، سائيڪلنگ فيشن ۾ بجلي جي فراهمي، يا خود-ليچنگ ٽائمڊ سرڪٽ ٺاهڻ کان وٺي سوين مختلف ايپليڪيشنن لاءِ استعمال ڪري سگھجي ٿو. ٽائمر کي ڳنڍڻ ۽ ترتيب ڏيڻ آسان آهي. سڀئي ترتيبون مستقل طور تي اندروني فليش ميموري ۾ محفوظ ڪيون وينديون آهن. ٽائمر 3V کان 28V سپلائي وول سان ڪم ڪري ٿو.tagاي ۽ 5 تائين سنڀالي سگھي ٿوamp/10amp ڪرنٽ جو (ماڊل تي منحصر). هي ٽائمر کي مختلف ايپليڪيشنن لاءِ لاڳو ڪري ٿو. ٽائمر جي وڌ ۾ وڌ ڪرنٽ کي ٻاهرين رلي جي استعمال سان وڌائي سگهجي ٿو. ٽائمر گهٽ پاور موڊ ۾ هلائي سگهي ٿو جيڪو بيٽري تي هلندڙ ايپليڪيشنن لاءِ موزون آهي. هڪ بلٽ ان فلائي بيڪ ڊاءِڊ انڊڪٽو لوڊ جي سڌي ڪنيڪشن جي اجازت ڏئي ٿو.
جلدtagاي رينج:
Max current: Output type: Minimum time duration: Maximum time duration: Idle current consumption:
گرمي پد جي درجه بندي
3-18 V DC 5 A version 6-28 V DC 10 A version 5 A or 10 A
مثبت يا سنڪ (زمين). ماڊل تي منحصر آهي
0.01 second 400 days 800 µA or 50 µA (in LOW POWER mode under certain conditions) -40 C + 80 C
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 3
· Do not short timer’s output to the ground. It would cause excessive current, possible device overheating, and smoke.
· Do not exceed the timer’s current capacity. · Do not reverse power supply polarity. It could
cause the timer’s internal components to fail and overheat.
· Do not put a timer into a hot environment causing it to exceed specified temperate range working conditions.
· Do not disconnect the ground from the timer while under power.
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 4
ٽائمر ورجن جو مقابلو ڪريو
What is the difference between Version V8 and V9? V9 contains more accurate frequency clock with just +/- 2sec per day fluctuation and software correction. V8 has +/- 2% fluctuation. V9 PCB is conformal coated providing an extra layer of protection.
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 5
ٽائمر جي وائرنگ ڊاگرام
3.1 Connecting the timer with Positive output
*** For up-to-date installation instructions and videos, visit http://doc2.us/main View Timer’s Cookbook at http://timers.shop/Timer-Cook-Book_ep_43-1.html
3.2 Connecting the timer with Sink (Ground) output
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 6
3.3 Connecting timer to the programmer.
Warning!!! When powering the timer from the programmer does not connect the load as the load could overload the USB supplied power. Do not connect external power to the timer as the power will be routed back to USB power source. It might destroy the USB power source as well as the programmer’s circuit.
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 7
3.4 Connecting timer to the programmer for in-circuit programming.
Warning!!! When powering the timer from the external source, do not connect the
programmer’s power line. It might destroy the USB power source as well as the programmer’s circuit.
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 8
1. Understanding Timer Delay Relay Function.
ملٽي فنڪشنل ٽائمر ۾ موجود آل ٽائيم ڊيلي رلي فنڪشن کي سمجهڻ هڪ خوفناڪ ڪم ٿي سگهي ٿو. ٽائمر رلي ۽ ٽائمر ترتيبن جي مختلف قسمن سان سرڪٽ ڊيزائن دوران، سوال جهڙوڪ ٽائمر ڊيلي فنڪشن کي ڇا شروع ڪري ٿو، ڇا ٽائمنگ پاور يا ٽرگر سگنل جي درخواست سان شروع ٿئي ٿي، آئوٽ پٽ پاور ڪيتري وقت تائين رهڻ گهرجي، وغيره، پيدا ٿي سگهن ٿا ۽ انهن جو جواب ڏيڻ لازمي آهي.
ٽائمر صرف هڪ منطقي ڪنٽرول سرڪٽ آهي جيڪو واقعن جي بنياد تي آئوٽ پُٽ پاور کي ڪنٽرول ڪري ٿو. عام طور تي، ٽائمر ٻن طريقن مان هڪ ذريعي شروع يا شروع ڪيو ويندو آهي:
· Application of power voltage · High or low trigger signal
The trigger signal can be one of the following: · A control switch (dry contacts): limit switch, push-button, the float switch · Voltagاي (پاور ٽرگر): ٻئي ڊوائيس مان سگنل آئوٽ پُٽ، پاور سگنل
ٽائمر جي ڪارڪردگي کي سمجهڻ ۾ مدد لاءِ اچو ته هن دستور ۾ استعمال ٿيندڙ عام اصطلاحن تي نظر وجهون.
· ان پٽ جلدtage power voltage ٽائمر تي لاڳو ڪيو ويو. چونڊيل فنڪشن تي منحصر ڪري، ان پٽ وولtage يا ته ٽائمنگ ايونٽ شروع ڪندو يا ٽائمر کي ٽرگر سگنل قبول ڪرڻ لاءِ تيار ڪرڻ لاءِ طاقت ڏيندو.
· Trigger Signal in certain timing functions, a trigger is used to initiate a timing event after the input voltage لاڳو ڪيو ويو آهي. جيئن مٿي ذڪر ڪيو ويو آهي ته هي ٽرگر يا ته ڪنٽرول سوئچ (ڊرائي ڪانٽيڪٽ سوئچ) يا پاور ٽرگر (وول) ٿي سگهي ٿو.tag۽.
· Output output voltagٽائمر کان e. آئوٽ پُٽ وول جو وقتtage کي چونڊيل ٽائمنگ ايونٽ ۽ ٽرگر طريقي سان ڪنٽرول ڪيو ويندو آهي.
Below (Figure 1) is a description of the timing functions. A timing chart shows the relationship between
انٽ واليمtagاي، ٽرگر سگنل، ۽ آئوٽ پُٽ. نوٽ ڪريو ته ٽرگر سگنل ڪجهه ٽائمر ڪمن لاءِ اختياري آهي ۽ ٻين لاءِ لازمي آهي. سڀني موجود ڪمن مان گذرڻ کان اڳ پهرين کي تفصيل سان ڏسو.
شڪل 1.
#
فنڪشن
1
دير تي
آپريشن
ان پٽ واليم جي درخواست تيtage، وقت جي دير (t) شروع ٿئي ٿي. وقت جي دير (t) جي آخر ۾، آئوٽ پُٽ توانائي سان ڀريل آهي. ان پٽ وولtagوقت جي دير واري رلي کي ري سيٽ ڪرڻ ۽ آئوٽ پُٽ کي ڊي-انرجائيز ڪرڻ لاءِ e کي هٽائڻ گهرجي.
Diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…….lh…….l’ }, { name: “output”, wave: ‘l.h……l.h……l’ }, {},{}, { name: “power”, wave: ‘lh…….lh…….l’ }, { name: “trigger”, wave: ‘l.H.l……H.l…..’ }, { name: “output”, wave: ‘l..h…..l..h…..l’ }]}
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 9
ٽائمر فنڪشن #1 ON DELAY آهي، اهو ڪجهه وقت کان پوءِ بجلي فراهم ڪرڻ جي اجازت ڏئي ٿو (t). ٻه ٽائمنگ چارٽ آهن، هڪ ٽرگر کان سواءِ ۽ ٻيو ٽرگر سان. ٽرگر جي چونڊ ٽائمر جي ترتيب دوران ڪري سگهجي ٿي. اچو ته پهرين چارٽ تي نظر وجهون جتي ٽائمر فراهم ڪيل ان پٽ وول ذريعي ٽرگر ٿئي ٿو.tage. هڪ ڀيرو ٽائمر کي بجلي فراهم ڪئي ويندي آهي، وقت جي دير (t) شروع ٿيندي آهي، وقت جي دير (t) جي آخر ۾ آئوٽ پُٽ توانائي سان ڀريل هوندو آهي ۽ ٽائمر کي بجلي ختم ٿيڻ تائين جاري رهندو آهي. پاور کي هٽائڻ سان ٽائمر سرڪٽ ري سيٽ ٿي ويندو آهي، ۽ ٽائمر ٻئي چڪر لاءِ تيار هوندو آهي. ٻيو چارٽ لاڳو ٿيندو آهي جڏهن ٽرگر آپشن چونڊيو ويندو آهي. هن خاص صورت ۾، ٽرگر هاءِ (مثبت) وول تيtage is selected. More on trigger options can be found later in the manual. Upon application of power, the timer is ready to accept the trigger signal. When the trigger is applied, the time delay (t) begins. At the end of the time delay (t) output is energized and stays on until power to the timer is removed. Another application of the trigger during time delay (t) or the output energized period, does not affect the timer function. Only the first application of the trigger matters. The diagrams can also be viewed or edited online at https://wavedrom.com/editor.html page.
2. Timer function table with charts
(نوٽ ڪريو ته فنڪشن نمبر # ٽائمر جي ترتيب دوران استعمال ڪيو ويندو.)
Figure 2. # Function
1 ON DELAY
آپريشن
جڏهن ان پٽ voltage لاڳو ٿئي ٿو، وقت جي دير (t1) شروع ٿئي ٿي. وقت جي دير (t1) مڪمل ٿيڻ کان پوءِ، آئوٽ پُٽ توانائي سان ڀريل ٿي ويندو آهي. وقت جي دير واري رلي کي ري سيٽ ڪرڻ ۽ آئوٽ پُٽ کي ڊي-انرجائيز ڪرڻ لاءِ، ان پٽ وولtagاي کي هٽائڻ گهرجي.
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…….lh…….l’ }, { name: “output”, wave: ‘l.h……l.h……l’ }, {},{}, { name: “power”, wave: ‘lh…….lh…….l’ }, { name: “trigger”, wave: ‘l.H.l……H.l…..’ }, { name: “output”, wave: ‘l..h…..l..h…..l’ } ]}
2 INTERVAL ON Upon the application of input voltage, the output becomes energized, initiating
the time delay period (t1). Once the time delay (t1) concludes, the output is
then de-energized. To reset the time delay relay, the input voltage هجڻ گهرجي
ڪٽيل آهي
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…….lh…….l’ }, { name: “output”, wave: ‘lh..l…..h..l…..’ }, {},{}, { name: “power”, wave: ‘lh…….lh…….l’ }, { name: “trigger”, wave: ‘l.Hl…….Hl……’ }, { name: “output”, wave: ‘l.h..l…..h..l….’ } ]}
اسان کي Facebook تي پسند ڪريو
يوٽيوب چينل
صفحو 10
# فنڪشن
آپريشن
3
REPEAT Upon application of voltage, time delay (t3) begins, and the output is delayed
CYCLE WITH for (t4), then energized for the time delay (t1) and de-energized for (t2) until
شروعاتي
(t3) timeout is reached.
دير
(t3) set to 0 will repeat the cycle indefinitely.
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…………….l’ }, { name: “output”, wave: ‘l.hlhlhlhlhlhlhlhl.’}, {},{}, { name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.Hl……………’ }, { name: “output”, wave: ‘l..hlhlhlhlhlhlhl..’ } ]}
4
REPEAT Upon application of voltage, time delay (t3) begins, and the output is energized
CYCLE WITH for (t4), then de-energized for the time delay (t1) and energized for (t2) until
شروعاتي
(t3) timeout is reached.
دير
(t3) set to 0 will repeat the cycle indefinitely.
(On first)
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…………….l’ }, { name: “output”, wave: ‘lhlhlhlhlhlhlhlhl..’}, {},{}, { name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.Hl……………’ }, { name: “output”, wave: ‘l.hlhlhlhlhlhlhlhl.’ } ]}
5 TRIGGERED Upon application of input voltage, the timer relay is ready to accept the trigger.
دير
When the trigger is applied, the time delay (t1) begins. At the end of the time
INTERVAL 2 delay (t1), the output is energized and remains energized for the time delay
Single Cycle (t2). At the end of the time delay (t2), the output is de-energized, and the relay
is ready to accept another trigger. During both time delays (t1) and (t2), the
trigger is ignored. When activated with a secondary trigger, the time delays are
set to t3 and t4.
Notes: Older documentation refers to function 5 as cycling. See functions 3, 4,
8, and 9 for cycling functionality.
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 11
# فنڪشن
آپريشن
Display diagram online: https://wavedrom.com/editor.html { signal: [ { name: “power”, wave: ‘lh…………….l’ },
{ name: “trigger”, wave: ‘l.Hl..HlHl…..Hl..’ },
{ name: “trigger”, wave: ‘l………Hl..Hl…’ }, { name: “output”, wave: ‘l..h.l.hl..h.l…..’ } ]}
6
REPEAT Upon application of voltage, time delay (t3) begins, and the output is delayed
CYCLE WITH for t4. Then t1 and t2 cycle start. The output is de-energized for the time delay
شروعاتي
(t1) and energized for (t2) until (t3) timeout is reached.
دير
When trigger 1 is activated, the cycle advances to the start of the t1 duration.
And when trigger 2 is activated, the cycle advances to the start of t2 duration.
(t3) set to 0 will repeat the cycle indefinitely.
Display diagram online: https://wavedrom.com/editor.html #Function 06 { signal: [ { name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l……Hl……….’ }, { name: “trigger”, wave: ‘l………..Hl…..’ }, { name: “output”, wave: ‘l…h.lh.l.hl.h.l..’ } ]}
7 DELAYED Upon the application of input voltage, the initial time delay (t1) starts. After INTERVAL the completion of this initial time delay (t1), the output becomes energized and Single Cycle stays energized for the duration of the second time delay (t2). Following the conclusion of this second time delay (t2), the output is de-energized. To reset the time delay relay, the input voltagاي کي هٽائڻ گهرجي.
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…….lh…….l’ },
{ name: “output”, wave: ‘l..h.l……h.l….’ },
{},{}, { name: “power”, wave: ‘lh…….lh…….l’ }, { name: “trigger”, wave: ‘l.Hl…….Hl……’ }, { name: “output”, wave: ‘l…h.l……h.l…’ } ]}
8
REPEAT Upon application of voltage, time delay (t3) begins, and the output is energized
سائيڪل
for the time delay (t1). At the end of the time delay (t1), the output is de-
(پهرين تي)
energized for the time delay (t2) and continues to cycle until (t3) is reached.
t3 کي 0 تي سيٽ ڪرڻ سان چڪر کي غير معين مدت تائين ورجايو ويندو.
t4 is used to insert an inactive phase. t4 set to 0 will force the cycle to end
when t3 expires.
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 12
# فنڪشن
آپريشن
Display diagram online: https://wavedrom.com/editor.html
{ signal: [ { name: “power”, wave: ‘lh…………….l’ }, { name: “output”, wave: ‘lhlhlhlhlhlhlhlhl..’}, {},{}, { name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.Hl……………’ }, { name: “output”, wave: ‘l.hlhlhlhlhlhlhlhl.’ }
]}
9
REPEAT Upon application of voltage, time delay (t3) begins, and the output is de-
سائيڪل
energized for the time delay (t1). At the end of the time delay (t1), the output is
(Off First) energized for the time delay (t2) and continues to cycle until (t3) is reached.
t3 کي 0 تي سيٽ ڪرڻ سان چڪر کي غير معين مدت تائين ورجايو ويندو.
t4 is used to insert an inactive phase. t4 set to 0 will force the cycle to end
when t3 expires.
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…………….l’ }, { name: “output”, wave: ‘l.hlhlhlhlhlhlhlhl.’}, {},{}, { name: “power”, wave: ‘lh…………….l’ },
{ name: “trigger”, wave: ‘l.Hl……………’ },
{ name: “output”, wave: ‘l..hlhlhlhlhlhlhl..’ } ]}
10
آن/بند
ان پٽ جي درخواست تي حجمtage, the timer relay is ready to accept a trigger.
دير
When the trigger is applied, the time delay (t1) begins. At the end of the time
delay (t1), the output is energized. When the trigger is removed, the output
remains energized for the time delay (t2). At the end of the time delay (t2), the
output is de-energized, and the time delay relay is ready to accept another
trigger. If the trigger is removed during the time delay period (t1), the output
will remain de-energized, and the time delay (t1) will reset. If the trigger is re-
applied during the time delay period (t2), the output will remain energized, and
the time delay (t2) will reset.
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.H……l………’ }, { name: “output”, wave: ‘l….h……..l….’ } ]}
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 13
# فنڪشن
آپريشن
11 TRIGGERED Upon application of input voltage, the timer relay is ready to accept a trigger.
ON DELAY When the trigger is applied, the time delay (t) begins. At the end of the time
delay (t), the output is energized and remains in that condition as long as either
the trigger is applied, or the input voltage remains. If the trigger is removed
during the time delay (t), the output remains de-energized, and the time delay
(t) ري سيٽ ڪيو ويو آهي.
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.H……l…H.l…’ }, { name: “output”, wave: ‘l….h…l………’ } ]}
12 OFF DELAY Upon application of input voltage, the timer relay is ready to accept a trigger. When the trigger is applied, the output is energized. Upon removal of the trigger, the time delay (t) begins. At the end of the time delay (t), the output is de-energized. Any application of the trigger during the time delay will reset the time delay (t) and the output remains energized.
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.H….l…Hl.Hl…’ },
{ name: “output”, wave: ‘l.h……l.h…..l.’ }
]}
13 SINGLE-SHOT Upon application of input voltage, the timer relay is ready to accept a trigger.
WITH TIME When the trigger is applied, the output is energized, and timer delay (t) begins.
ري سيٽ ڪريو
Any application of the trigger during the time delay will reset the time delay (t)
and the output remains energized.
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.H….l.Hl.Hl…..’ }, { name: “output”, wave: ‘l.h…l..h……l..’ } ]}
14 SINGLE-SHOT Upon application of input voltage، ٽائمر رلي ٽرگر قبول ڪرڻ لاءِ تيار آهي. جڏهن ٽرگر لاڳو ڪيو ويندو آهي، آئوٽ پُٽ توانائي سان ڀريل هوندو آهي، ۽ وقت جي دير (t) شروع ٿيندي آهي. وقت جي دير (t) دوران، ٽرگر کي نظرانداز ڪيو ويندو آهي. وقت جي دير (t) جي آخر ۾، آئوٽ پُٽ توانائي سان ڀريل هوندو آهي، ۽ وقت جي دير ٻئي ٽرگر کي قبول ڪرڻ لاءِ تيار هوندي آهي.
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.H….l.HlHl……’ }, { name: “output”, wave: ‘l.h…l..h…l…..’ } ]}
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 14
# فنڪشن
آپريشن
15 TRIGGERED Upon application of input voltage, the timer relay is ready to accept the trigger.
دير
When the trigger is applied, the time delay (t1) begins. At the end of the time
INTERVAL delay (t1), the output is energized and remains in that condition for the time
Single Cycle delay (t2). At the end of the time delay (t2), the output is de-energized, and the
relay is ready to accept another trigger. During both time delay (t1) and time
دير (t2)، ٽرگر کي نظرانداز ڪيو ويندو آهي.
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.Hl.Hl..H……l..’ }, { name: “output”, wave: ‘l…h..l…h..l….’ } ]}
16 INTERVAL ON Upon application of input voltage, the timer relay is ready to accept the trigger. WITH OFF When the trigger is applied, the output is energized, and the time delay (t) TRIGGER begins. At the end of the time delay (t), the output is de-energized. Application of trigger during time delay (t) will cause time delay (t) to expire and output is de-energized.
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.Hl.Hl.H….l…..’ }, { name: “output”, wave: ‘l.h..l..h…l……’ } ]}
17 INTERVAL ON Upon application of input voltage, the timer relay is ready to accept the trigger. TRIGGER When the trigger is applied, the output is energized, and the time delay (t)
CONTROLLED begins. At the end of the time delay (t), the output is de-energized. Removal of the trigger during time delay (t) will cause time delay (t) to expire and output is de-energized.
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.H..l.H…..l…..’ }, { name: “output”, wave: ‘l.h..l.h….l……’ } ]}
18 FREE FORM Upon application of voltage, time delay begins, and free-form pattern
ONE TIME programmed by the user is executed. When the pattern is completed it can be
(Up to 48
retriggered again.
تشڪيل
نقطا)
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 15
# فنڪشن
آپريشن
19 FREE FORM Upon application of voltage, time delay begins, and free pattern cycle
REPEATED programmed by the user is executed. Once started the cycle will be repeated
(Up to 48
over and over.
تشڪيل
نقطا)
20 CANCELED Upon application of input voltage, the output is energized, and the time delay INTERVAL (t) begins. At the end of the time delay (t), the output is de-energized. If the trigger is applied during the time delay (t) the output is de-energized and the delay canceled. Input voltagوقت جي دير واري رلي کي ري سيٽ ڪرڻ لاءِ e کي هٽائڻ گهرجي.
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh……lh……..l’ }, { name: “trigger”, wave: ‘l…………Hl….’ }, { name: “output”, wave: ‘lh…..l.h…l…..’ } ]}
21 SINGLE SHOT Upon application of input voltage, the timer is ready to accept a trigger. When TIME RESET the trigger is applied, the output is energized, and timer delay (t) begins. Any HOLD ON application of the trigger during the time delay will reset the time delay (t) and TRIGGER the output remains energized. If the trigger still applied after the delay (t) the output remains energized until the trigger is removed.
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.Hl..HlHl..H….l.’ }, { name: “output”, wave: ‘l.h..lh….lh….l.’ } ]}
22 FOLLOW Upon application of input voltage, a standard relay is ready to accept a trigger. When the trigger is applied, the output is energized. The output continues to be energized until the trigger is removed, at which point the output is deenergized.
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.Hl..HlHl..H….l.’ }, { name: “output”, wave: ‘l.hl..hlhl..h….l.’ } ]}
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 16
# فنڪشن
آپريشن
23 WATCHDOG When an input voltage is applied, the timer relay’s output becomes energized,
1
and the relay is primed to receive a trigger signal. If the trigger is activated at
any point during the first-time delay period (t1), this action will reset the timer
for t1, and the output continues to remain energized. Once the time delay
period t1 concludes without further triggers, the output is then de-energized for
a second time delay period (t2) and then the cycle repeats.
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.HlHl….HlHlHlHl.’ }, { name: “output”, wave: ‘lh……lh……..l’ } ]}
24 FUNCTION 24 When an input voltage لاڳو ڪيو ويندو آهي، ٽائمر ٽرگر ان پٽ قبول ڪرڻ لاءِ تيار هوندو آهي. جيڪڏهن ٽرگرز جي وچ ۾ مدت t1 کان گهٽ آهي ۽ ٽائمر مسلسل n ٽرگرز کي ڳڻيندو آهي ته پوءِ آئوٽ پُٽ ٽرگر جي پٺيان هلندو آهي جيستائين ٽرگرز جي وچ ۾ مدت t1 کان وڌي نه وڃي.
Display diagram online: https://wavedrom.com/editor.html { signal: [ { name: “power”, wave: ‘lh…………….l’ }, { name: “trg blue”, wave: ‘l.HlHlHlHl..HlHlHl.’ }, { name: “trg green”, wave: ‘l………..HlHlHl.’ }, { name: “output”, wave: ‘l…..hlhl………’ } ]} Practical use. This function can be used as a turn signal alarm configured to be activated after set number of cycles. The timer output will be activated for t2 or the duration of the trigger. The blue and green triggers are connected to turn signal bulbs on each side. The trigger is configured to mode 2 and the trigger function set to XOR. Function XOR will allow either blue or green trigger to activate the alarm, but the simultaneous execution during hazard activation would cancel the trigger.
25 OUTPUT ON Upon application of input voltage, the timer relay is ready to accept trigger
TRIGGER input. When the trigger is applied the output is energized for the time delay
CHANGE (t1). The release of the trigger also energizes the output for time (t2). The
optional delay (t3) and (t4) can be inserted before the output is energized.
Display diagram online: https://wavedrom.com/editor.html
{ سگنل: [
{ name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.H…l..H…..l…’ }, { name: “output”, wave: ‘l.hl..h.lhl….h.l.’ } ]}
26 BUTTON Upon application of input voltage, the timer relay is ready to accept trigger
INTERFACE input. With short (< t2) application of trigger the output is energized for the
سان
time delay (t1). The second application of the trigger will de-energize the
TIMEOUT output. With long (>t2) application of trigger, the output is energized and held
energized until the trigger is removed.
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.H.l.Hl…..Hl.Hl.’ }, { name: “output”, wave: ‘l.h.l.h….l.h..l..’ } ]}
اسان کي Facebook تي پسند ڪريو
يوٽيوب چينل
صفحو 17
# فنڪشن
آپريشن
28 FUNCTION 28 Upon application of input voltage, the timer relay is ready to accept trigger
input. With short (< t2) application of trigger the output is energized for the
time delay (t1). The second application of the trigger will reset delay (t1). With
long (>t2) application of trigger, the output is energized and held energized
until the trigger is removed. With long (>t2) application of trigger during the
active output, the timeout is canceled and output stays energized until the
trigger is removed.
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.H.l.HlHl…HlH.l.’ }, { name: “output”, wave: ‘l.h.l.h….l.h…l.’ } ]}
29 INTERVAL Upon application of input voltage, the timer relay is ready to accept the trigger.
سان
When the trigger is applied the output is energized and the time delay (t1)
LOCKOUT begins. At the end of the time delay (t1), the output is de-energized and
Single Cycle remains in that condition for the time delay (t2). During both time delay (t1)
۽ وقت جي دير (t2)، ٽرگر کي نظرانداز ڪيو ويندو آهي.
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.Hl.Hl..H……l..’ },
{ name: “output”, wave: ‘l.h.l….h.l…….’ }
]}
30
پاور
Timer operation is intended as a countdown timer. The countdown stops when
INDEPENDENT power is removed but continues when power is reapplied. To run the timer in
ٽائمر
this mode first configure timer time, function and trigger. Activating trigger for
> 5 secs resets the timer and countdown starts. When the sum of the time is
greater than the preset time the output becomes active. Activating trigger for >
5 secs resets the countdown.
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…lh…..lh….l’ }, { name: “output”, wave: ‘l…………..h..l’ } ]}
31 REPEAT The function is similar to Function #5 (Repeat cycle). The duration of the first
RANDOM active phase of the cycle is randomly calculated with the range set between t1
سائيڪل
and t2. The passive phase is between t3 and t4.
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 18
# فنڪشن
آپريشن
Display diagram online: https://wavedrom.com/editor.html { signal: [ { name: “power”, wave: ‘lh…………….l’ },
{ name: “trigger”, wave: ‘lHl…………….’ },
{ name: “output”, wave: ‘lh.l.h..l.h….l…’ }, {}, {}, { name: “power”, wave: ‘lh…………….l’ }, { name: “output”, wave: ‘lh.l.h..l.h….l…’ } ]}
32 FOLLOW Upon application of input voltage، آئوٽ پُٽ توانائي سان ڀريل آهي، ۽ وقت جي دير
WITH INITIAL (t) begins. At the end of the time delay (t), the output follows the trigger level.
ON
When the trigger is applied, the output is energized and continues to be
energized until the trigger is removed. When the trigger is removed the output
غير متحرڪ آهي.
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l…..HlHl..H….l.’ }, { name: “output”, wave: ‘lh.l..hlhl..h….l.’ } ]}
33 COUNTER Upon application of input voltage، ٽائمر ٽرگر قبول ڪرڻ لاءِ تيار آهي. هڪ ڀيرو ٽرگر معلوم ٿئي ٿو ته سائيڪلن جو اڳواٽ تعداد (n) آئوٽ پُٽ مدت (t1) لاءِ چالو ڪيو ويندو آهي. فعال آئوٽ پُٽ دوران ٽرگر کي نظرانداز ڪيو ويندو آهي. وقت جي دير (t1) جي آخر ۾، ٽائمر ٽرگر قبول ڪرڻ لاءِ تيار آهي.
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘lP…………….l’ }, { name: “output”, wave: ‘l…h.l..h.l..h.l..’ } ]}
34 DELAY ON Upon application of input voltage, the timer relay is ready to accept a trigger.
سان
When the trigger is applied, the time delay (t1) begins. At the end of the time
TIMEOUT delay (t1), the output is energized. The output remains energized for a period
of t2 unless the trigger is removed. If trigger is removed the output de-
energized and cycle ends.
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.H….l..H……l.’ }, { name: “output”, wave: ‘l…h..l….h…l..’ } ]}
35 OFF DELAY Upon application of input voltage, the output is energized for t2. The timer
سان
relay is ready to accept a trigger. When the trigger is applied, the output is
INITIALIZATI energized. Upon removal of the trigger, the time delay (t) begins. At the end of
ON
the time delay (t), the output is de-energized. Any application of the trigger
during the time delay will reset the time delay (t) and the output remains
متحرڪ.
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 19
# فنڪشن
آپريشن
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…………….l’ },
{ name: “trigger”, wave: ‘l….Hl…HlHl…..’ },
{ name: “output”, wave: ‘lh.l.h..l.h….l…’ } ]}
36 FOLLOW Upon application of input voltage, the timer relay is ready to accept a trigger.
سان
When the trigger is applied, the output is energized and continues to be
LOCKOUT energized until the trigger is removed. When the trigger is removed the output
is de-energized and period t1 starts. During the t1 period the timer will not
respond to the trigger.
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.Hl.HlHl.H…l….’ }, { name: “output”, wave: ‘l.hl…hl..h..l….’ } ]}
37 FLIP FLOP Upon application of input voltage, the timer relay is ready to accept a trigger.
سان
Once the trigger is detected preset number of cycles (n) the output is flipped.
COUNTER
Display diagram online: https://wavedrom.com/editor.html { signal: [ { name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘lP…………….l’ }, { name: “output”, wave: ‘lhlhlhlhlhlhlhlhlhl’ } ]}
38 FOLLOW Upon application of input voltage, the timer relay is ready to accept a trigger.
سان
When the trigger is applied, the output is energized and continues to be
LOCKOUT 2 energized until the trigger is removed. When the trigger is removed the output
is de-energized and period t1 starts. During the t1 period the timer will not
respond to the trigger and the lockout time t1 will reset.
Display diagram online: https://wavedrom.com/editor.html { signal: [ { name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.Hl.Hl.Hl..Hl..Hl.’ }, { name: “output”, wave: ‘l.hl……..hl..hl.’ } ]}
39 SINGLE-SHOT Upon application of input voltage, the timer relay is ready to accept a trigger. WITH TWO When the trigger is applied, the output is energized, and the time delay (t1) TRIGGERS begins. During the time delay (t1), the trigger is ignored. At the end of the time delay (t1), the output is de-energized, and the time delay is ready to accept another trigger. The same applies to trigger 2 (Green)
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.H….l.HlHl……’ }, { name: “trigger”, wave: ‘l………….Hl…’ }, { name: “output”, wave: ‘l.h…l..h…lh.l..’ } ]}
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 20
# فنڪشن
آپريشن
40 SINGLE-SHOT Upon application of input voltage, the timer relay is ready to accept a trigger.
WITH TWO When the trigger is applied, the output is energized, and the time delay (t1)
TRIGGERS 2 begins. During the time delay (t1), the trigger is ignored. At the end of the time
delay (t1), the output is de-energized, and the time delay is ready to accept
another trigger. Application of the trigger 2 would reset the time delay to t2.
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.H….l.Hl……..’ }, { name: “trigger”, wave: ‘l………..Hl…..’ }, { name: “output”, wave: ‘l.h…l..h……l..’ } ]}
41 ACCUMULAT Upon application of input voltage, the timer relay is ready to accept a trigger.
OR
When the trigger is applied, the output is energized, and timer delay (t) begins.
Any application of the trigger during the time delay will reset the time delay (t)
and the output remains energized. Each consecutive trigger application
increases the timer delay (t1).
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.Hl.HlHl.HlHlHl…’ }, { name: “output”, wave: ‘l.h.lH…lH…..l..’ } ]}
42 SINGLE SHOT Upon application of input voltage, the timer relay is ready to accept a trigger. WITH CANCEL When the trigger is applied, the output is energized, and timer delay (t) begins. Any application of the trigger during the time delay will reset the time delay (t) and the output remains energized. Each consecutive trigger application sets the next time delay until reached the timer delay (t4). The next application of trigger will cancel the output. The output is also cancelled if time delay is set to 0.
Display diagram online: https://wavedrom.com/editor.html
{ signal: [ { name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.Hl.HlHl….Hl.Hl.’ }, { name: “output”, wave: ‘l.h.lh….l..h.l…’ }
]}
43 WATCHDOG When an input voltage is applied, the timer relay’s output becomes energized,
2
and the relay is primed to receive a trigger signal. If the trigger is activated at
any point during the first-time delay period (t1) the time delay period (t1) is
reset, and stays reset while trigger is active. The output stays energized. When
trigger goes inactive the time delay (t1) starts. Once the time delay period t1
concludes without further triggers, the output is then de-energized for a second
time delay period (t2). Trigger application is ignored during delay period (t2).
Upon completion of delay period (t2) the output is energized, and delay period
(t1) is reset.
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 21
# فنڪشن
44 TRIGGERED DELAY
INTERVAL Multiple Cycles
آپريشن
Display diagram online: https://wavedrom.com/editor.html { signal: [ { name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.HlHl.Hl.HlHlHlHl.’ }, { name: “output”, wave: ‘lh….l..h……..l’ } ]}
ان پٽ جي درخواست تي حجمtage، ٽائمر رلي ٽرگر قبول ڪرڻ لاءِ تيار آهي. جڏهن ٽرگر لاڳو ڪيو ويندو آهي، وقت جي دير (t1) شروع ٿيندي آهي. وقت جي دير (t1) جي آخر ۾، آئوٽ پُٽ توانائي سان ڀريل هوندو آهي ۽ وقت جي دير (t2) لاءِ ان حالت ۾ رهندو آهي. وقت جي دير (t2) جي آخر ۾، آئوٽ پُٽ توانائي سان ڀريل هوندو آهي، ۽ رلي ٻيو ٽرگر قبول ڪرڻ لاءِ تيار هوندو آهي. وقت جي دير (t1) ۽ وقت جي دير (t2) ٻنهي دوران، ٽرگر کي نظرانداز ڪيو ويندو آهي.
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.Hl.Hl..H……l..’ }, { name: “output”, wave: ‘l…h..l…h..l….’ } ]}
45 INTERVAL Upon application of input voltage, the timer relay is ready to accept the trigger.
سان
When the trigger is applied the output is energized and the time delay (t1)
LOCKOUT begins. At the end of the time delay (t1), the output is de-energized and
Multiple Cycles remains in that condition for the time delay (t2). During both time delay (t1)
۽ وقت جي دير (t2)، ٽرگر کي نظرانداز ڪيو ويندو آهي.
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.Hl.Hl..H……l..’ }, { name: “output”, wave: ‘l.h.l….h.l..h.l..’ } ]}
46
آن/بند
ان پٽ جي درخواست تي حجمtage, the timer relay is ready to accept a trigger.
DELAY WITH When the trigger is applied, the time delay (t1) begins. At the end of the time
CANCEL delay (t1), the output is energized. The output remains energized for the time
delay (t3). If trigger is applied while output is active the time delay (t2) begins.
At the end of the time delay (t2), the output is de-energized. After output is de-
energized the time delay (t4) begins during which the trigger application is
نظرانداز ڪيو ويو.
Display diagram online: https://wavedrom.com/editor.html { signal: [ { name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.H…l…H…l….’ }, { name: “output”, wave: ‘l….h…….l…..’ } ]}
47
آن/بند
ان پٽ جي درخواست تي حجمtage, the timer relay is ready to accept a trigger.
DELAY WITH When the trigger is applied the output is activated and the time delay (t1)
CANCEL AND begins. At the end of the time delay (t1), the output continues to be energized
FOLLOW even if trigger is removed. The output remains energized for the time delay
(t3). If trigger is applied while output is active the time delay (t2) begins. At
the end of the time delay (t2), the output is de-energized. After output is de-
energized the time delay (t4) begins during which the trigger application is
نظرانداز ڪيو ويو.
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 22
# فنڪشن
آپريشن
Display diagram online: https://wavedrom.com/editor.html { signal: [ { name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘l.HlH.l…H…lHl..’ }, { name: “output”, wave: ‘l.hlh……..l.hl..’ } ]}
48 COUNTER Upon application of input voltage, the timer is ready to accept the trigger. WITH TIME Once the trigger is detected preset number of cycles (n) applied during period
RESTRICTION shorter than t1 the output is activated for the duration (t2). The trigger is ignored during the active output. At the end of the time delay (21), the timer is ready to accept the trigger.
Display diagram online: https://wavedrom.com/editor.html { signal: [
{ name: “power”, wave: ‘lh…………….l’ }, { name: “trigger”, wave: ‘lpppl..pplpl.pppl..’ }, { name: “output”, wave: ‘l..h.l………h.l.’ } ]}
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 23
3. Timer trigger.
As described above timer is initiated or triggered by one of two methods: · Application of power voltage · High or low trigger signal
The trigger signal can be one of the following: · A control switch (dry contacts): limit switch, push-button, or float switch · Voltagاي (پاور ٽرگر): ٻئي ڊوائيس مان سگنل آئوٽ پُٽ، پاور سگنل
3.1 Timer trigger operation with charts.
شڪل 3.
هاءِ ٽرگر
Upon application of power the time delay relay is ready to accept the trigger. The transition of the voltage on the trigger wire from low to high will trigger the start of the time delay (t).
گهٽ ٽرگر
Upon application of power, the time delay relay is ready to accept the trigger. The transition of the voltage on the trigger wire from high to low will trigger the start of the time delay (t).
To use trigger input with dry contact (like switch or button), trigger wire would need to be `pulled’ to either High or Low voltage. ٽائمر جي ترتيب ٽرگر تار کي يا ته هاءِ وولٽ تي ڇڪڻ لاءِ سيٽ ڪرڻ جي اجازت ڏئي ٿي، جتي تار کي هاءِ وولٽ تي رکڻ لاءِ هڪ ننڍڙو ڪرنٽ لڳايو ويندو آهي.tagٽرگر تار کي گهٽ وولٽ تي رکڻ سان اي يا گرائونڊ ڪيو ويوtage. هيٺ ڏنل جدول ڏيکاري ٿو ته ٽرگر وائر پل کي هاءِ يا لو تي ڪڏهن ترتيب ڏيڻو آهي.
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 24
3.2 سابقampٽرگر سيٽ اپ جو مرحلو.
شڪل 4.
Trigger pull
وصف
تشڪيل
Trigger pulled to
گھٽ
The trigger is set to be pulled to Low. Upon button or switch engagement the trigger voltage jumps to High (positive voltag۽.
The trigger could also be a positive voltage from the external source applied to the trigger wire.
Note: event could be triggered either by applying or removing power.
The shown Pull-down resistor is built into the timer and does not need to be connected externally.
Wiring diagram and trigger chart
Trigger pulled to
هاءِ
The trigger is set to be pulled to High. Upon button or switch engagement the trigger voltage jumps to Low (grounded).
The trigger could also be the Ground applied to the trigger wire.
Note: event could be triggered either by applying or removing ground.
The shown Pull-up resistor is built into the timer and does not need to be connected externally.
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 25
3.3 Timer trigger configuration table.
(نوٽ ڪريو ته ٽائمر ٽرگر فنڪشن نمبر # ٽائمر ترتيب دوران استعمال ڪيو ويندو.)
شڪل 5.
ٽرگر جي ترتيب
******
1 2 6 10 14 3 7 11 15 4 8 12 16 5 9 13 17
Trigger pull
گھٽ گھٽ اعليٰ اعليٰ
فعال ٽرگر
هيٺ ڏنل نوٽس ڏسو
وصف
هاءِ گهاٽو اوچو
Trigger is disabled For dry contacts between trigger wire and positive. For a case where the voltage is applied to a trigger. For dry contacts between trigger wire and ground. For a case where the ground is applied to the trigger.
* Trigger functions ensure the trigger transition from inactive to activate state upon startup. Applies to functions: all **Trigger acts as an enable/disable switch. Applies to function: 5, 6, 8, 9, 18, 19, 31 ***Trigger utilizing flip-flop operation. Applies to functions: all
Exampفنڪشن 2 استعمال ڪندي 10، 14، ۽ 5 تي ٽرگر سيٽنگز جو لي. جڏهن ٽرگر 2 تي سيٽ ڪيو ويندو آهي، اهو چڪر شروع ڪري ٿو. ٽرگر کي 10 تي سيٽ ڪرڻ سان فنڪشن آن ۽ آف ٽوگل ٿي ويندو آهي. ان کي 14 تي سيٽ ڪرڻ سان فلپ فلاپ ٽرگر طور ڪم ڪري ٿو، جيڪو پهرين ٽرگر سان فنڪشن کي آن ۽ ٻئي سان بند ڪري ٿو. هي فلپ فلاپ ميڪانيزم سڀني فنڪشنز تي لاڳو ٿئي ٿو.
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 26
3.4 Multi-trigger operation.
سرڪٽ ۾ ٻه ٽرگر ان پٽ آهن: نيرو ۽ سائو. ٻنهي ٽرگرن کي هڪ ئي وقت استعمال ڪرڻ لاءِ ٽرگرن کي مناسب ترتيبن تي سيٽ ڪريو ۽ هيٺ ڏنل مان هڪ مان ٽرگر فنڪشن چونڊيو:
Trigger Function Name Description
صرف نيرو
Blue acts as a function trigger. Green is enabled for two
trigger functions such as Function 38.
صرف سائو
سائو رنگ هڪ فنڪشن ٽرگر طور ڪم ڪري ٿو، نيرو رنگ نظرانداز ڪيو ويندو آهي.
۽
Logical AND operation. For a timer to be triggered
both triggers must be Active.
OR
Logical OR operation. For a timer to be triggered, only
one of the triggers needs to be Active.
XOR
Logical XOR operation. For a timer to be triggered
only one of the triggers has to be in Active, not both.
Blue main / Green
Blue acts as a function trigger, Green cancels the
منسوخ ڪريو
function execution by resetting the timer.
Blue main / Green
Blue acts as a function trigger, Green cancels the
cancel V2
function execution only if Blue trigger is inactive by
resetting the timer.
AND then OR
Logical AND operation. For a timer to be triggered
both triggers must be Active. Then active trigger
maintained with Logical OR where only one if the
triggers need to be active.
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 27
هيٺ ڏنل ڊاگرام هر چونڊيل ٽرگر فنڪشن لاءِ پيدا ٿيل جامع فائنل ٽرگر کي ڏيکاري ٿو. ٽائمر نيرو ۽ گرين ٽرگرز کي ضم ڪندي هن فائنل ٽرگر ويليو کي ڳڻپيو ويندو آهي، ۽ پوءِ هن حساب ڪيل ويليو کي لاڳاپيل فنڪشن تي لاڳو ڪندو آهي.
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 28
'بليو مين/گرين ڪينسل' ٽرگر جي ڪارڪردگي هڪ منفرد انداز ۾ ڪم ڪري ٿي. مثال طور، فنڪشن #01 کي هڪ نمائندي اڳوڻي طور تي غور ڪريو.ample. نيرو ٽرگر چالو ڪرڻ سان فنڪشن جو ڪم شروع ٿئي ٿو، جڏهن ته سائي ٽرگر کي مشغول ڪرڻ سان جاري فنڪشن سرگرمي کي ري سيٽ ڪرڻ جو ڪم ٿئي ٿو.
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 29
ڇڪڻ واري حد
حد اهو طئي ڪري ٿي ته ٽائمر جي تسليم ڪرڻ کان اڳ ٽرگر کي فعال يا غير فعال رهڻ گهرجي.
شروعاتي محرڪ نظرانداز ڪريو
شروعاتي پاور اپ کان فوري پوءِ جو عرصو جنهن دوران ٽائمر ٽرگر سگنل جو جواب نه ڏيندو آهي.
محرڪ جلدtage
محرڪ جلدtage can reach the supply voltage. The table below shows the levels at which the trigger threshold is reached.
Trigger config
Active when high Active when low
Threshold (Approx.)
1.2 وي 1.0 وي
Edge Direction
Low -> High High -> Low
Event generated when
Input crosses 1.2 V Input drops below 1.0 V
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 30
ٽائمر آئوٽ پُٽ موڊ
ٽائمر آئوٽ پُٽ موڊ استعمال ڪندڙ کي يا ته فوري آئوٽ پُٽ سيٽ ڪرڻ جي اجازت ڏئي ٿو، جتي آئوٽ پُٽ فوري طور تي اچي ۽ بند ٿي وڃي، يا بتدريج واڌ/گهٽتائي، جتي آئوٽ پُٽ PWM (پلس ويڊٿ ماڊوليشن) ڪنٽرول ٿيل هجي ۽ آرamps up to 100% duty in about 4 seconds. The gradual output is excellent for the lighting system to increase and dim the lights gradually.
5. Timer Output type
In some circumstances, it is required to supply reversed output to the load, so instead of supplying power to the load during the time delay (t), the output is de-energized. The following diagram shows a sampٽائمر آپريشن عام ۽ الٽ آئوٽ پُٽ سان.
ٽائمر عام آئوٽ پُٽ سان اڳ ۾ ترتيب ڏنل آهي.
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 31
ٽائمر پروگرامنگ
ٽائمر جي ترتيبن کي تبديل ڪرڻ لاءِ پروگرامر سرڪٽ جي ضرورت آهي.
پروگرامر استعمال ڪيو ويندو آهي:
· Reading timer’s configuration. · Changing timer’s configuration. · Uploading selected function into the timer’s memory. · Controlling timer’s output. · Reading timer’s trigger lines.
ٽائمر پروگرامنگ يا ته ٽائمر کي سڌو سنئون پروگرامر سان ڳنڍي ڪري سگهجي ٿو شڪل 2.3 يا پروگرامر کي ان-سرڪٽ پروگرامنگ لاءِ ٽائمر سان ڳنڍي ڪري سگهجي ٿو شڪل 2.4.
ٽائمر جي پروگرامنگ ۾ مناسب فنڪشن، ٽرگر ۽ ٽائمنگ پيرا ميٽرز چونڊڻ شامل آهن. فنڪشن 12 (ٽائيم آف ڊيلي)، ٽرگر 2 (وڌندڙ وول تي ٽرگر) لوڊ ڪرڻ لاءِ هيٺ ڏنل قدمن تي عمل ڪريو.tage) ۽ 10 سيڪنڊن جي دير:
· Connect the timer to the programmer. · Power the programmer by plugging into a computer or USB power bank. · Move the programmer’s switch to ON position to supply the power to the timer. If the
switch was in ON position when programmer was powered on then turn the switch to OFF position wait for a couple of seconds and then turn it back on. · After a couple of seconds, the programmer blue LED would light up confirming the programmer is communicating with the timer. · ڳولھيو timers.shop Wi-Fi network on the laptop or phone and connect to it. · Open the browser on the phone/computer and enter address 192.168.4.1 into the address bar of the browser. · Go to the Timer’s Config menu and make necessary changes.
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 32
مشڪلاتون
علامتون
حل جا مرحلا
The timer is not connecting to · Verify three wires (Black, Red, and White) are
the programmer, and the
properly connected between the programmer and the
programmer’s blue LED is not
timer and not shorted. Shorting White and Red might
کولڻ.
render the programmer inoperable.
· Verify continuity of each wire.
· Turn the programmer’s power switch to the OFF
پوزيشن.
· Push the programmer’s two buttons located near the
USB socket. The buttons could be pushed in any
sequence. This will restart the programmer.
· Supply power to the timer by moving the switch to the
ON position. It might take a couple of seconds for the
programmer to communicate to the timer.
· Contact the support if you are still having issues with
the programmer’s connection.
The Select Function menu does not display any available functions, and the Timers Configuration menu is empty, including its functions and timing settings. The configuration seems to have been deleted from the timer. The programmer successfully communicates with the timer, but when going to select the function, the drop-down is empty.
· The programmer is not successfully connected to the timer and cannot pull the existing timer information to be displayed. For the programmer to display available functions and settings, the timer must successfully communicate with the programmer, and the blue LED should be ON.
· The programmer might not have the up-to-date functions list for V9 timers. Make sure the programmer has been updated to the latest version. More information can be found here: https://timers.shop/Universal-Programmerfirmware_ep_61-1.html
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 33
Shorting the programmer’s red and white wires may damage the programmer’s data line. To test the programmer’s data line, connect to the programmer’s WI-FI, open the following address in the browser: http://192.168.4.1/testdataline, and follow the instructions.
8. گھٽ پاور موڊ
The timer can be configured in Low Power mode, which drops the idle current consumption to a much lower value. This mode makes the timer suitable for battery operation. For example, if we take a 9V battery with 500mAh capacity, we can calculate the duration the timer can run in idle mode. 500mah/0.020ma = 25000 hours. The timer’s Low Power mode is enabled by default. But several conditions must be met to have the lowest power draw: 1. The trigger should be configured to #2 (if used), without Pull up. The trigger voltage should be at 0v
for low power consumption. 2. The output is at 0V. 3. The following Functions are enabled for Low Power mode: 2, 10, 12 – 17, 20 29.
Note: Due to the internal power storage the timer will not reset with a brief power interruption. To reset the timer configured with Low Power mode, the power outage 3 سيڪنڊن کان وڌيڪ هجڻ گهرجي.
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 34
لوازمات
9.1 Timer programming circuit (sold separately)
10. YouTube Videos
https://timers.shop/Timer-V8-Videos_ep_57-1.html
11. مفيد لنڪس
Latest firmware and function updates: https://timers.shop/Universal-Programmer-firmware_ep_61-1.html
اسان کي Facebook تي پسند ڪريو
YouTube Channel Page 35
دستاويز / وسيلا
 |
TIMERS V8.0, V9.0 Multi Functional Timer Relay [pdf] استعمال ڪندڙ دستياب V8.0, V9.0, V8.0 V9.0 Multi Functional Timer Relay, V8.0 V9.0, Multi Functional Timer Relay, Timer Relay |