microtech-DESIGNS-logo

Microtech DESIGNS e-Loop Mini Wireless Vehicle Detection System

microtech-DESIGNS-e-Loop-Mini-Wireless-Vehicle-Detection-System -product

وضاحتون

  • فرائض: 433.39 ايم ميگا
  • سيڪيورٽي: 128-bit AES انڪرپشن
  • حد: 30 ميٽر تائين
  • بيٽري جي زندگي: 3 سالن تائين
  • بيٽري جو قسم: AA 1.5V 3000 m/a ليتيم بيٽري x2 (شامل)
  • متبادل بيٽري جو قسم: Everready AA 1.5V ليتيم بيٽري x2

e-LOOP ميني فيٽنگ جون هدايتون

3 سادي مرحلن ۾ انسٽاليشن

قدم 1 - ڪوڊنگ اي-لوپ ميني ورزن 3.0
آپشن 1. مقناطيس سان مختصر رينج ڪوڊنگ

Power up the e-Trans 50, then press and release the CODE button. The blue LED on the e-Trans 50 will light up, now place the magnet on the CODE recess on the e-Loop, the yellow LED will flash, and the blue LED on the e-Trans 50 will flash 3 times. The systems are now paired, and you can remove the magnet.

آپشن 2. Long-range coding with a magnet (up to 50 meters)

Power up the e-Trans 50, then place the magnet on the code recess of the e-Loop, the yellow code LED will flash once the magnet and the LED come on solid, now walk over to the e-Trans 50 and press and release the CODE button, the yellow LED will flash and the blue LED on the e-Trans 50 will flash 3 times, after 15 seconds the e-loop code LED will turn off.

قدم 2 - ڊرائيو وي تي e-LOOP ميني بيس پليٽ کي فٽ ڪرڻ

  1.  Face the arrow on the base plate towards the gate. Using a 5mm concrete masonry drill, drill the two mounting holes 55mm deep, then use the 5mm concrete screws supplied to fix to the driveway.

قدم 3 - اي-لوپ ميني کي بيس پليٽ تي فٽ ڪرڻ
(سڄي پاسي واري تصوير کي ڏسو)

  1.  Now fit the e-loop Mini to the base plate using the 4 hex screwssupplied, making sure the arrow also points towards the gate (this will ensure the keyway is aligned). The e-Loop will become active after 3 minutes.

نوٽ: Ensure hex screws are tight as this forms part of the water-sealing process.
اهم: the e-Loop’s vehicle detection and radio range capabilities.

Wireless Vehicle Detection System EL00M-RAD Version 3

تبديل ٿيندڙ موڊ
The e-LOOP is set to exit mode for the EL00M, and set to presence mode for the EL00M-RAD as default. To change the mode from presence mode to exit mode on the EL00M-RAD e-LOOP, use the menu via the
e-TRANS-200 or the Diagnostics remote.نوٽ Do not use presence mode as a personal safety function.

microtech-DESIGNS-e-Loop-Mini-Wireless-Vehicle-Detection-System -fig-1

Microtech ڊيزائن

 

دستاويز / وسيلا

microtech DESIGNS e-Loop Mini Wireless Vehicle Detection System [pdf] هدايتون
PROOF1-MD_e-Loop, EL00M-RAD Version 3, e-TRANS-200, e-Loop Mini Wireless Vehicle Detection System, e-Loop Mini, Wireless Vehicle Detection System, Vehicle Detection System, Detection System, System

حوالو

تبصرو ڇڏي ڏيو

توهان جو اي ميل پتو شايع نه ڪيو ويندو. گهربل فيلڊ نشان لڳل آهن *