FlySpark-logo

FlySpark F4 V1 Stack Flight Controller

FlySpark-F4-V1-Stack-Flight-Controller-productوضاحتون

  • پيداوار جو نالو:
    فلائي اسپارڪ F4 V1 BLS 60A اسٽيڪ
  • AI خاصيتون:
    Sensor Fusion, PID Autotuning, Adaptive Filtering
  • سافٽ ويئر سپورٽ:
    بيٽا فلائيٽ، آئي اين اي وي، آرڊو پائلٽ، اي ايم يو فلائيٽ، اسڪائي برش
  • ESC Communication:
    BLHeli_S بلوٽوٿ ۽ USB-C
  • رابطي:
    3-6 ايس ليپو
  • طول و عرض:
    47.8mm (L) x 47.5mm (W) x 18.3mm (H)
  • چڙهڻ:
    30.5 x 30.5mm 4mm سوراخ سائيز سان
  • وزن:
    34 جي

FlySpark-F4-V1-Stack-Flight-Controller-fig-9 FlySpark-F4-V1-Stack-Flight-Controller-fig-10

پيداوار جي استعمال جون هدايتون

فلائي اسپارڪ F4 V1 فلائيٽ ڪنٽرولر

ترتيب:
Refer to the user manual for the layout of the flight controller.

پردي ڪنيڪشن:
Connect peripherals as per the provided diagram.

ايپ ۽ ايف سي ترتيب:
Use the recommended apps and follow the configuration instructions.

ايف سي فرم ويئر اپڊيٽ:
Connect the flight controller to a PC via USB for firmware updates.

فلائي اسپارڪ BLS 60A 4-ان-1 ESC

ترتيب:
Check the layout guide in the manual for proper installation.

موٽر ۽ پاور ڪيبل سان ڪنيڪشن:
Connect motors and power cables securely.

ESC ترتيب:
Use the FlySpark app for ESC configuration settings.

ESC فرم ويئر اپڊيٽ:
Follow the provided steps to update the firmware for ESC.

فلائي اسپارڪ F4 V1 BLS 60A اسٽيڪFlySpark-F4-V1-Stack-Flight-Controller-fig-1

تفصيل ختمviewFlySpark-F4-V1-Stack-Flight-Controller-fig-20

FlySpark-F4-V1-Stack-Flight-Controller-fig-2 FlySpark-F4-V1-Stack-Flight-Controller-fig-3

پيڪيجFlySpark-F4-V1-Stack-Flight-Controller-fig-4.1

  • FlySpark F4 V1 Flight Controller x 1
  • FlySpark BLS 60A 4-in-1 ESC x 1
  • 35V 1000uF گھٽ ESR Capacitor x 1
  • M3 نائلون نٽ x 4
  • SH 1.0mm 25mm-ڊگھائي 8pin ڪيبل (FC-ESC ڪنيڪشن لاءِ) x 1 SH 1.0mm 75mm-ڊگھائي 6pin ڪيبل* x 1
  • M3*30mm اندروني-مسدس اسڪرو x 4
  • DJI 6pin ڪيبل (80mm) x 1
  • XT60 پاور ڪيبل (100mm) x 1

FlySpark-F4-V1-Stack-Flight-Controller-fig-5.2

ايف سي ڪنيڪشن ڊاگرامFlySpark-F4-V1-Stack-Flight-Controller-fig-6

ايف سي ۽ اي ايس سي ڪنيڪشن لاءِ گائيڊ

طريقو 1:

  • Using 8.Pin JST CableFlySpark-F4-V1-Stack-Flight-Controller-fig-7

طريقو 2:

سڌو سولڊرنگ

  • هيٺ ڏنل پيڊ جي تعريفن تي عمل ڪندي، هر ڇيڙي تي 8 تارن کي 8 پيڊن تي سولڊر ڪريو.FlySpark-F4-V1-Stack-Flight-Controller-fig-8

فلائيٽ ڪنٽرولر جون خاصيتون

FlySpark-F4-V1-Stack-Flight-Controller-fig-11.2

  • 6 پن ڪيبل استعمال ڪريو O3 ايئر يونٽ سان گڏ اچي ٿو FlySpark-F4-V1-Stack-Flight-Controller-fig-12.1
  • استعمال ٿيل 6-پن ڪيبل FlySpark F4 V1 BLS 60A اسٽيڪ سان گڏ اچي ٿو.

FlySpark-F4-V1-Stack-Flight-Controller-fig-13

F C Firmware  update
To update the firmware for your FlySpark F4 VI flight controller, please follow these steps:
Connect the Flight Controller to Your PC:

  • Use a USB cable to connect the FlySpark F4 VI flight controller to your PC

Open Betaflight I INAV Configurator.

  • . Launch the Betaflight Configurator or INAV Configurator on your PC. For this guide, we’ll use Betaflight Configurator as an exampلي.

Navigate to Firmware Flashing:

  • In the Betaflight Configurator, navigate to the ‘Firmware Flashing’ page.

Select Target and Flash Firmware:

  •  Choose the target firmware for ‘Flyspark F4 VI’ from the dropdown menu.
  • Initiate the firmware flashing process.

نوٽ:
The Flyspark F4 VI flight controller does not support wireless firmware flashing. It must be  performed using a USB connection to your PC.

FlySpark-F4-V1-Stack-Flight-Controller-fig-14

Flyspark BLS 60A 4-in-l ESCFlySpark-F4-V1-Stack-Flight-Controller-fig-15

موٽر ۽ پاور ڪيبل سان ڪنيڪشنFlySpark-F4-V1-Stack-Flight-Controller-fig-16

ESC Specs FlySpark F4 V1 BLS 60A StackFlySpark-F4-V1-Stack-Flight-Controller-fig-17

ESC فرم ویئر اپڊيٽ
هي 8-بٽ 50A ESC BLHeliS فرم ويئر سان اڳ ۾ لوڊ ٿيل آهي پر ان کي Bluejay فرم ويئر تي پڻ فليش ڪري سگهجي ٿو، جيڪو RPM فلٽرنگ ۽ بائي ڊائريڪشنل Dshot سپورٽ پيش ڪري ٿو. فرم ويئر کي اپڊيٽ ڪرڻ لاءِ انهن قدمن تي عمل ڪريو:

  1. Prepare Your Drone:
    Remove all propellers from your drone for safety.
  2. Connect ESC to Flight Controller:
    Ensure the flight controller is properly connected to the ESC, then power up the drone. This step ensures the ESC initializes correctly.
  3. PC سان ڳنڍيو:
    Use a USB Type-C cable to connect the flight controller to your computer.
  4. Access Firmware Configuration:
    Open the Chrome browser and visit: www.esc-configurator.com
  5. Flashing Steps:
    Follow the firmware flashing steps displayed on the configurator website. Ensure you select the appropriate options for flashing to Bluejay firmware.

FlySpark-F4-V1-Stack-Flight-Controller-fig-21

احتياط:FlySpark-F4-V1-Stack-Flight-Controller-fig-19

  • PROPELLERS OFF: REMOVE ALL PROPELLERS.
  • SECURE CONNECTION: ENSURE SECURE ESC CONNECTION.
  • FOLLOW STEPS: FOLLOW FLASHING INSTRUCTIONS CAREFULLY.
  • STABLE POWER: ENSURE STABLE POWER SUPPLY.
  • www.FlySpark.in

FAQs

مان ESC فرم ويئر کي ڪيئن اپڊيٽ ڪريان؟

To update the ESC firmware, follow these steps: 1. Prepare Your Drone: Remove all propellers for safety. 2. Connect ESC to Flight Controller: Ensure proper connection to the ESC and power up.

دستاويز / وسيلا

FlySpark F4 V1 Stack Flight Controller [pdf] استعمال ڪندڙ دستياب
F4 V1, BLS 60A, F4 V1 Stack Flight Controller, F4 V1, Stack Flight Controller, Flight Controller, Controller

حوالو

تبصرو ڇڏي ڏيو

توهان جو اي ميل پتو شايع نه ڪيو ويندو. گهربل فيلڊ نشان لڳل آهن *