Cosmic Byte ECLIPSE TRI Mode Controller User Manual

Cosmic Byte ECLIPSE TRI Mode Controller

پيداوار جي وضاحت

نوٽ: All specifications are for reference and may vary depending on usage and environment.

پيڪيج مواد

• Eclipse Controller × 1
• Replaceable D-Pad × 1
• 2.4G Receiver × 1
• USB Type-C Cable (1.5m) × 1
• استعمال ڪندڙ جو دستياب × 1

هاءِ لائيٽس

Mode Switching Position: From left to right: Bluetooth – 2.4G – NS (Xinput Bluetooth, 2.4G Receiver, Switch)

آپريشن جون هدايتون

HOME CB Indicator Light

• Blue – iOS and Android
• Orange – 2.4G Mode

پهريون ڀيرو ڪنيڪشن

• 2.4G وائرليس موڊ
  • Set the mode switch toggle to 2.4G (Middle).
  • USB رسيور کي پنهنجي ڊوائيس ۾ پلگ ان ڪريو.
  • While the controller is powered off, press and hold the Pairing button for 3 seconds.
  • The logo indicator will flash rapidly. Once it turns solid and the controller vibrates briefly, the connection is successful.
• بلوٽوٽ موڊ
  • Set the mode switch toggle to Bluetooth (Left).
  • While powered off, press and hold the Pairing button for 3 seconds.
  • The logo indicator will flash rapidly.
  • On your device (PC/Android/iOS), enable Bluetooth and select ‘Xbox Wireless Controller’.
  • When the logo light turns solid and the controller vibrates, the pairing is complete.
• وائرڊ موڊ
  • Connect the controller to your device using the included USB Type-C cable.
  • Wired mode activates automatically when connected.

ٻيهر ڪنيڪشن
To reconnect to the last paired device (with the same mode), short-press the Home button.

جوائس اسٽڪ ايڊجسٽمينٽ

• Dead Zone Toggle:
  • Press and hold Left and Right Stick (LS/RS) for 5 seconds to switch between 5% and 0% deadzone.
  • Controller will vibrate to confirm the change.
• Active Zone Shape Toggle:
  • Press and hold M + LS or RS for 5 seconds to toggle between 10% square zone and 0% circle zone.

 Turbo and Continuous Fire

• دستي ٽربو
  • Press M + A while holding the A button to enable manual turbo (continuous fire).
  • Logo light will flash red rapidly.
• خودڪار ٽربو
  • Press M + A again to switch to auto turbo. Press again to cancel turbo.
  • A single press of A will now fire continuously.
• Clean all Turbo
  • Press M button twice and hold M for 5 secs, controller will vibrate & clean all Turbo settings.
• ٽربو اسپيڊ ايڊجسٽمينٽ
  • Hold M + Right Stick Up/Down to increase or decrease turbo speed.
  • Vibration feedback indicates change.

ABXY Lighting Adjustment

• Press M + Right Stick Left and Right to adjust brightness.
• 4 Brightness Levels: 0% → 30% → 70% → 100%

کمپن جي شدت جي ترتيب

• Press and hold M + Right Stick Up to increase vibration intensity.
• Press and hold M + Right Stick Down to decrease.
• 4 Levels: 0% (off) → 30% → 70% → 100%

ABXY لي آئوٽ سوئچ

Use the layout switch on the front to toggle between XBOX-style and Alternate-style layouts.

Rapid Trigger Adjustment
Adjust LT/RT trigger travel distance using the trigger mode switch on the back for quick/short press functionality.

حساب ڪتاب

• اسٽيڪ ۽ ٽرگر حساب ڪتاب
  • ڪنٽرولر تي طاقت.
  • رکو View + M + Menu for 3 seconds to enter calibration.
  • LED1 and LED3 will flash.
  • Rotate both sticks clockwise 3 full turns.
  • Fully press both triggers 3 times.
  • Switch triggers to short travel mode, then press them fully 3 more times.
  • دٻايو View نڪرڻ.
  • LED1 and LED3 will stay solid for 5 seconds before powering off.
• گيوروسڪوپي ڪيليبريشن
  • Power off the controller and place it on a flat surface.
  • رکو View + A + B + Home to enter gyro calibration.
  • LED1 and LED2 will flash.
  • After 1 second, press Menu to complete calibration. LEDs will turn off.
  • Calibration must be performed in XBOX (ABXY) layout mode.

Macro Programming (M1/M2 Buttons)

• While connected, hold M + M1 or M2 for 3 seconds to enter programming mode.
• Press the desired button to assign (e.g., A, B, etc.).
• Press M1 or M2 again to save and exit.

نوٽ: If no button is selected, M1/M2 will be blank. Up to 21 Programmable buttons: A/B/X/Y/D-pad/LB/RB/LT/RT/L3/R3/Menu/View/Joysticks

بجلي بند

• Hold the Home button for 5 seconds to power off.
• 10 منٽن جي غير فعال ٿيڻ کان پوءِ خودڪار پاور آف.

ڪنٽرولر ري سيٽ
Use a small pin to press the Reset hole to restore factory settings.

 Joystick Force Adjustment (Roller-Based)
The Cosmic Byte Eclipse controller features adjustable joystick tension using a built-in roller mechanism. Follow the steps below to customize the joystick force according to your preference:

• Locate the joystick roller at the base of each analog stick.
• To increase joystick resistance, rotate the roller clockwise.
• To decrease joystick resistance, rotate the roller counter-clockwise.
• Make adjustments gradually and test after each rotation to find your preferred setting.

نوٽ: The roller mechanism allows for fine-tuning of joystick stiffness for better precision or quicker flick response in different game types (e.g., FPS vs Racing).

بيٽري اشاري گائيڊ

• گھٽ بيٽري: Logo light flashes red once every 10 minutes
• چارج ڪرڻ: Logo light breathes green
• مڪمل چارج ٿيل: Logo light turns off

موبائل ايپ ڊائون لوڊ ڪريو

Download and install the “Key Linker” App from the Google Play Store or Apple App Store for advanced customization and controller adjustments.

وارنٽي

• The Eclipse Tri-Mode Controller carries a 1-year warranty against manufacturing defects only.
• Physical, water damage, and tampered مصنوعات وارنٽي تحت coveredڪيل ناهن.

Scan the QR Code to know the Warranty Claim Procedure.

حمايت جي تفصيل

• Customer Care Number: +91 7351615161 (Mon-Sat 10am to 6pm)
• WhatsApp Support: +91 7351615161
• اي ميل: cc@thecosmicbyte.com