ACL-SC-DMX Allanson Dmx Spi Master Lighting Controller Series User Manual

DMX/SPI Master Lighting Controller

ACL-DMX/SPI-LC Wiring Diagram

---

ACL-DMX/SPI-LC

DMX/SPI Master Lighting Controller
وائرنگ ڊراگرام

نوٽ: Wiring diagrams in the following scenarios are for reference only. They are not project specific, and they only show generic wirings scenarios. Components, cable types, and distance could vary depending on project size requirements.

---

cservice@allanson.com | 1.800.661.7251 | www.allanson.com
Information in this manual is subject to change without prior notice

Scenarios for DMX System

In a DMX system, the Master Controller sends commands to control the colors, or values, of RGB/RGBW components. The Sub-Controller manages a series of RGB/RGBW components that respond to a single command. There can be multiple Sub-Controllers connected to a Master Controller.

The Allanson ACL-SC-DMX Sub-Controller is UL approved, compatible with RGB and RGBW modules. The ACL-SC-DMX also has an IP65 ingress protection rating, making it ideal for a wide range of lighting applications.

When additional RGB/RGBW components need to be connected to a Sub-Controller, the Allanson ACL-PR-4CH-5A Power Repeater can be used.

The ACL-PR-4CH-5A duplicates and boosts the RGB/RGBW signal, allowing more module series to be connected to the same Sub-Controller. The new Power Repeater is also UL approved and IP65 rated.

DMX System Scenario (Different commands given to multiple groups of LEDs)

1. Cat 5/6 Cable
   (1-2 ft recommended, distance as short as possible)
2. RJ45 اڊاپٽر
   (ACL-SIG-AD)
3. RJ45 اڊاپٽر
4. نوٽ: Add terminator (orange-yellow) to the last sub-controller. At a maximum of 2000ft from the first to last sub-controller
5. Sub-controller
   (ACL-SC-DMX)
6. بجلي جي فراهمي
7. 5 wire 18 GA Cable
8. پاور ريپيٽر
   (ACL-PR-4CH-5A)
9. RGBW modules / RGB tubings
10. capped wire
11. RGBW module
12. RGB Rigid/Flexible Border Tubing

Scenarios for SPI System

In the SPI system, a few new components can be used to boost signal strength and extend the range to max 1000ft with cat5e or cat6 cable.

SPI range extender (RX/TX) is a single channel which controls one group of addressable modules.

SPI splitter splits signal from one channel into multiple signals. The same command is being copies and sent to receivers.

4X SPI range extender has 4 channels that controls max 4 different groups of addressable modules in different commands. it also has booster function that can transmit signal over a long distance.

SPI system – Scenario #1

The Master Controller can be connected directly to modules if the distance is shorter than 30 ft, an adaptor is required.

1. Cat 5/6 Cable
   (max. 30 ft)
2. RJ45 اڊاپٽر
   (ACL-SIG-AD)
3. RGB Addressable Modules
4. بجلي جي فراهمي

SPI system – Scenario #2

SPI range extenders (transmitter and receiver) are being used as a pair when addressable modules are more than 30ft away.
Single channel only ( one group of modules).

1. Cat 5/6 Cable
   (1-2 ft recommended, distance as short as possible)
2. RJ45 اڊاپٽر
   (ACL-SIG-AD)
3. RJ45 اڊاپٽر
4. Keep Minimum Distance
5. SPI Range Extender Transmitter
   (ACL-SPI-EXT-Tx)
6. SPI Range Extender Transmitter
7. Cat 5/6 Cable
   (Max. 1000ft)
8. بجلي جي فراهمي
9. SPI Range Extender Receiver
10. SPI Range Extender Receiver
    (ACL-SPI-EXT-Rx)
11. RGB Addressable Modules

SPI system – Scenario #3

SPI Splitter is being when sending the same command to several groups of RGB addressable modules.

1. Cat 5/6 Cable
   (1-2 ft recommended, distance as short as possible)
2. RJ45 اڊاپٽر
   (ACL-SIG-AD)
3. RJ45 اڊاپٽر
4. Keep minimum distance
5. SPI Splitter
6. SPI Splitter
   (ACL-SPI-Tx/0-SPL/4)
7. Cat 5/6 Cable
   (Max. 1000ft)
8. بجلي جي فراهمي
9. SPI Range Extender Receiver
   (ACL-SPI-EXT-Rx)
10. Range Extender Receiver
11. RGB Addressable Modules

SPI system – Scenario #4

4x SPI Range Extender is being used for controlling various group of to several groups of RGB addressable modules that listen to different commands.

1. S1 کان S10
   (use 4 ports max.)
2. Cat 5/6 Cable
   (1-2 ft recommended, distance as short as possible)
3. RJ45 اڊاپٽر
   (ACL-SIG-AD)
4. 4xSPI Range Extender
5. 4xSPI Range Extender
   (ACL-SPI-EXT-Tx/4-SPL/0)
6. Cat 5/6 Cable
   (Max. 1000ft)
7. بجلي جي فراهمي
8. Range Extender Receiver
   (ACL-SPI-EXT-Rx)
9. Range Extender Receiver
10. RGB Addressable Modules

SPI system – Scenario #5

The Master Controller can be connected directly to modules from 1000ft away via the Boosted SPI ports. A receiver is required.

1. Cat 5/6 Cable
   (Max. 1000 ft)
2. SPI Range Extender Receiver
   (ACL-SPI-EXT-Rx)
3. SPI Range Extender Receiver
4. بجلي جي فراهمي
5. RGB Addressable Modules

Multi-protocols

For large-scale signage applications, DMX, SPI, and Boosted SPI Systems could co-exist.
The system diagram is distributed across three pages for clarity.

1. Cat 5/6 Cable
   (1-2 ft recommended, distance as short as possible)
2. DMX سسٽم
3. SPI Boosted System
4. SPI System

Multi-protocol – DMX System Set-Up

1. S1 کان S10
   SPI System
2. SB1 to SB6
   SPI Boosted System
3. DMX/SPI Master Controller
4. Cat 5/6 Cable
   (1-2 ft recommended, distance as short as possible)
5. RJ45 اڊاپٽر
   (ACL-SIG-AD)
6. RJ45 اڊاپٽر
7. نوٽ: Add terminator (orange-yellow) to the last sub-controller. At a maximum of 2000ft from the first to last sub-controller
8. Sub-controller
   (ACL-SC-DMX)
9. بجلي جي فراهمي
10. 5 wire 18 GA Cable
11. RGBW modules / RGB tubings
12. پاور ريپيٽر
    (ACL-PR-4CH-5A)
13. capped wire
14. RGBW module
15. RGB Rigid/Flexible Border Tubing

Multi-protocol – SPI System Set-Up

1. D1 کان D16
   DMX سسٽم
2. SB1 to SB6
   SPI Boosted System
3. DMX/SPI Master Controller
4. Cat 5/6 Cable
   (1-2 ft recommended, distance as short as possible)
5. RJ45 اڊاپٽر
   (ACL-SIG-AD)
6. RJ45 اڊاپٽر
7. Keep Minimum Distance
8. SPI Range Extender Transmitter
   (ACL-SPI-EXT-Tx)
9. SPI Range Extender Transmitter
10. Cat 5/6 Cable
    (Max. 1000ft)
11. بجلي جي فراهمي
12. SPI Range Extender Receiver
    (ACL-SPI-EXT-Rx)
13. SPI Range Extender Receiver
14. RGB Addressable Modules

Multi-protocol – SPI Boosted System Set-Up

1. D1 کان D16
   DMX سسٽم
2. DMX/SPI Master Controller
3. S1 کان S10
   SPI System
4. SB1 to SB6
5. Cat 5/6 Cable
   (1-2 ft recommended, distance as short as possible)
6. SPI Range Extender Receiver
   (ACL-SPI-EXT-Rx)
7. SPI Range Extender Receiver
8. بجلي جي فراهمي
9. RGB Addressable Modules

---

cservice@allanson.com | 1.800.661.7251 | www.allanson.com

# 21-552
11.11.25

دستاويز / وسيلا

Allanson ACL-SC-DMX Allanson Dmx Spi Master Lighting Controller Series [pdf] استعمال ڪندڙ دستياب ACL-DMX-SPI-LC, ACL-SC-DMX, ACL-PR-4CH-5A, Allanson Dmx Spi Master Lighting Controller Series, Allanson Dmx Spi Master Lighting Controller Series, Allanson Dmx Spi, Master Lighting, Controller, Series

حوالو

• استعمال ڪندڙ دستي