2023 SCOT T
LUMEN e RIDE MANUAL
2023 LUMEN eRIDE
THE LUMEN eRIDE SHOULD BE ADJUSTED EXACTLY TO THE RIDER FOR MAXIMUM SAFETY AND RIDEABILITY.
Please contact your authorized SCOTT dealer for advice in order to avoid technical problems or any harm.
LEGEND
![]() |
TORQUE REQUIRED |
NO GREASE REQUIRED | |
GREASE REQUIRED | |
CARBON GREASE REQUIRED | |
THREADLOC REQUIRED | |
BEARING FIT REQUIRED | |
TORX TOOL SIZE | |
TORQUE AMOUNT | |
TASK DIFFICULTY | |
HEX TOOL SIZE |
GEOMETRY & TECHNICAL DATA
SEATPOST | mm | 31.6 |
SEATPOST CLAMP | mm | 34.9 |
TRAVEL | mm | 130 Rr 150 Ft |
SHOCK LENGTH | mm | 165 |
SHOCK STROKE | mm | 45 |
HARDWARE M.FRAME HARDWARE LINKAGE | mm mm | Trunnion |
MAX ROTOR | mm | 8 x 20 |
MAX CHAINRING | Tooth | 36 |
MAX TYRE WIDTH | in | 2.6 |
CHAINLINE | mm | 55 |
MY23 LUMEN eRIDE | SM | MED | LG | XL | ||
A | Head tube angle | ° | 65.5 | 65.5 | 65.5 | 65.5 |
B | Head tube length | mm | 110 | 110 | 120 | 135 |
C | Top tube horizontal | mm | 562 | 589 | 620 | 645 |
D | standover height | mm | 765 | 767 | 780 | 800 |
E | BB offset | mm | -38.5 | -38.5 | -38.5 | -38.5 |
F | BB height | mm | 338.5 | 338.5 | 338.5 | 338.5 |
G | Wheelbase | mm | 1176 | 1206 | 1240 | 1270 |
I | BB center to TST | mm | 415 | 440 | 480 | 520 |
J | Seat angle | ° | 76.8 | 77 | 77.2 | 77.5 |
K | Chainstay | mm | 450 | 450 | 450 | 450 |
L | Reach | mm | 416 | 446 | 476 | 501 |
M | Stack | mm | 615 | 615 | 625 | 638 |
Fork Length | mm | 540 | 540 | 540 | 540 | |
Trail | mm | 126 | 126 | 126 | 126 |
GEOMETRY & TECHNICAL DATA
Please observe the maximum seatpost insertion so not to damage the frame.
Small: 150 mm Max Insertion
Medium: 175 mm Max Insertion
Large: 215 mm Max Insertion
X-Large: 255 mm Max Insertion
Please note that on the small sized frame it is only possible to use a 500 ml water bottle, with a side entry cage.
HEADSET ADJUSTMENT
It is important to install the headset correctly depending on the set up required. There are two types of headset cups.
0° & 0.6° ( 64° & 65°) These can be indentified from the stamp on the inner surface of the headset cup.
The headset is available in two options:
288251 SYN HEADSET ZS56/28.6-ZS56/40 MTB 290060 SCO HEADSET CUP KIT SPARK 22
Do not use a standard headset tool to remove these plastic headset cups.
Slacker
Steeper
SAG ADJUSTMENT
- Wear your normal riding gear, set the sage meter to zero & the twinloc in the open position.
- Gently sit on the bike allowing the sag meter to move. Once completed dismount the bike gently. Check the value.
If the sag value is not to your liking within the sag range indicated, adjust the shock pressure as indicated above.
You may need to use this specific valve extender depending on which shock pump you have. 297520 SCO eRIDE REAR SHOCK VALVE EXTENDOR 23
TWINLOC
LUMEN | NAME | PART NO. | CAM TYPE | DROPPER |
LUMEN eRIDE 900 SL | TWINLOC TSP3 | 290009 | BLUE CAM | YES |
LUMEN eRIDE 900 | TWINLOC TSP3 | 290009 | BLUE CAM | YES |
LUMEN eRIDE 910 | TWINLOC TSP3 | 290009 | BLUE CAM | YES |
TQ SYSTEM MANUALS
CABLE ROUTING
Rear Brake & Rear Derailleur
Dropper Seatpost
Twinloc
Speed Sensor
SPARE PARTS
297265 SCO eRIDE BRAKE MOUNT LUMEN 23
290054 SCO HANDLEBAR CABLEGUIDE KIT MTB IC 22
297270 SCO eRIDE CABLEGUIDE/COVER KIT LUMEN 23
297269 SCO eRIDE SHOCK COVER LUMEN 23
297516 SCO eRIDE INTERNAL CABLEGUIDE 23
420010 SCO LUMEN eRIDE 23 CS/ST PROTECTOR
297266 SCO eRIDE CHAINGUIDE LUMEN 23
286000 SCO DROPOUT SRAM UDH 21
290016 SCO AXLE RWS 148X12 SPARK PLUG 22290059 SCO STEM SPACER/TOP CAP SY MTB XC 22
290057 SCO STEM SPACER/TOP CAP SY MTB COMBO 22
290058 SCO STEM SPACER/TOP CAP SY MTB DC 22
290056 SCO HEADSET SPACER KIT IC MTB 22
297673 SCO MAIN PIVOT SPARK 22/LUMEN 23
292668 BLD SHOCK NOODLE LINKIN 22
294540 SCO eRIDE TQ RANGER EXTENDER HOLDER
294537 SCO eRIDE TQ RANGE EXTENDER
294538 SCO eRIDE TQ RANGE EXTENDER CABLE MTB
294767 SCO eRIDE LINKAGE BAR INNER LUMEN 23
296209 SCO eRIDE TQ SPEEDSENSOR 23
296217 SCO eRIDE TQ LOCKRING SET 23
296216 SCO eRIDE TQ H-BAR REMOTE SET 23
MANUFACTURER’S GUARANTEE,
When purchasing a new SCOTT bicycle from an authorized SCOTT dealer, SCOTT grants a manufacturer’s guarantee subject to the following provisions.
CONDITIONS
The manufacturer’s guarantee is only granted to the first-time buyer of a SCOTT bicycle who has purchased it from an authorized SCOTT dealer. The manufacturer’s guarantee only applies if the bicycle is registered to the first buyer at www.scott-sports.com within ten days of purchase.
DURATION
The manufacturer’s guarantee is granted from the date of purchase for a period of five years on bicycle frames and rear ends. The guarantee period is reduced to three years, if the SCOTT bicycle is not serviced at least once a year by an authorized SCOTT dealer. Maintenance services must be carried out in accordance with the maintenance instructions in the SCOTT manual and must be confirmed there by the stamp and signature of the authorized SCOTT dealer.
For frames and rear ends of Category 5 bicycle models and for rigid forks manufactured by SCOTT, the duration of the manufacturer’s guarantee is limited to two years.
If a defect on the SCOTT bicycle is remedied within the scope of a manufacturer’s guarantee or a warranty claim, the duration of the manufacturer’s guarantee is not extended. The manufacturer’s guarantee ends, when the first-time buyer transfers ownership of the SCOTT bicycle to a third person.
ASSERTION
The manufacturer’s guarantee is provided by SCOTT Sports SA, Route du Crochet 11, 1762 Givisiez, Switzerland. The buyer must inspect the SCOTT bicycle immediately after purchase and notify his authorized SCOTT dealer at once in writing of any obvious defects. Hidden defects must be reported immediately after their discovery. In the event of a guarantee claim, the SCOTT bicycle must be handed over to an authorized SCOTT dealer. The latter will contact SCOTT to remedy the defect. The assertion of a guarantee claim always requires the presentation of the original proof of purchase as well as the proof of maintenance service in the SCOTT manual.
Performance of SCOTT in the event of a guarantee claim
In the event of a guarantee claim, SCOTT will, at its own discretion, repair the defect or replace the defective product with a product of similar quality, whereby colour and model deviations are possible. If a repair or replacement is not possible, a purchase price refund will be made taking into account previous use. SCOTT is entitled to commission third parties to remedy the defect.
LIMITATIONS
The manufacturer’s guarantee applies exclusively to frames, swingarms and rigid forks of SCOTT bicycles. Bicycle components are excluded from this manufacturer’s guarantee.
The manufacturer’s guarantee does not apply to normal wear and tear, damage caused by accidents or other excessive force on the SCOTT bicycle, corrosion, improper maintenance, incorrect assembly and assembly of unsuitable components or accessories as well as cosmetic defects, for example in the varnish.
The manufacturer’s guarantee does not apply to SCOTT bicycles that have been used in a rental shop.
MISCELLANEOUS
These manufacturer’s guarantee provisions apply to all SCOTT bicycles as of model year 2023. Statutory warranty rights of the buyer and guarantees of component manufacturers (Shimano, SRAM etc.) remain unaffected by this manufacturer’s guarantee.
The place of jurisdiction for all disputes in connection with this manufacturer’s guarantee is Freiburg, Switzerland. This manufacturer’s guarantee is subject to Swiss law to the
exclusion of all legislation that refers to foreign law.
© SCOTT Sports SA 2023. All rights reserved.
The information contained in this manual is in various languages but only the English version will be relevant in case of conflict.
P.E.D Zone C1, Rue Du Kiell 60
6790 Aubange
Belgium Distribution: SSG (Europe) Distribution Center SA SCOTT Sports SA
11 Route du Crochet
1762 Givisiez
2022 SCOTT Sports SA
www.scott-sports.com
Email: webmaster.marketing@scott-sports.com
Documents / Resources
![]() |
SCOTT 2023 LUMEN eRIDE [pdf] Owner's Manual 2023 LUMEN eRIDE, 2023 LUMEN eRIDE, LUMEN eRIDE |