Scope SP1015A Tablet PC User Guide

Scope SP1015A Tablet PC

Introduction

This operation guide is for the user to understand and familiarize with our products as soon as possible. Here, we briefly introduce the key layout and definition of our products in a graphical way, and give some basic instructions for some basic operations

The key layout and definition

Key function description:

1. Power button: Press and hold 3S to switch on/off, and short press again to wake up the screen.
2. Volume button
3. Earphone seat
4. USB charging interface / USB seat / OTG seat: USB line interface; OTG line interface, transfer mobile hard disk, keyboard, mouse.
5. TF Card Block
6. Front Camera
7. MIC
8. Rear camera
9. Speaker.

Desktop introduction

Main Interface Introduction:

Navigation Bar

Basic operations

Boot/shutdown

• In the off state, long press the power button (3 seconds) to boot, and the machine after the boot LOGO enters the main interface. It is also possible to insert the charger when it is turned on (please use the dedicated 5V/2A charger provided by the company).
• In the boot state, press and hold the power button for 3 seconds, and the shutdown option will pop up. Touch Shutdown to shutdown.
• In the case of a crash or inconvenient touch, long press the power button for 10 seconds to force the shutdown.

Power/USB charging detection

Battery usage indication
When the battery is in use, as the battery power decreases, the white bar on the desktop’s navigation bar battery icon will gradually decrease to the icon .

Charge status indication
Connect the USB cable to the USB charger and then connect it to the USB port of the machine to charge it. The battery icon in the navigation bar of the desktop indicates that the battery is being charged. Do not insert or remove the charger during charging. When the battery icon fills up (go to the navigation bar application shortcut setting interface, the battery level is displayed as “see icon”

Attention:

1. Do not perform the firmware upgrade after the machine is powered off. Charge the battery beforehand.
2. There will be a charging icon when the machine is powered off and plugged in.
3. When the USB is plugged into the computer, the machine automatically charges. Don’t perform any operations when the machine’s power is low.

Suggestions:
When the user uses and upgrades for the first time, the machine is charged to 100% of the power to make sure the battery level is relatively accurate.

Specification

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used following the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Specific Absorption Rate (SAR) information: This Tablet PC meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement the SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: Tablet PC has also been tested against this SAR limit. This device was tested for typical body-worn operations with the back of the Tablet PC kept 0mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 0mm separation distance between the user’s body and the back of the Tablet PC. The use of belt clips, holsters, and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements and should be avoided.