BRITELINE
GEN2 1
External version
INSTALLATION INSTRUCTIONS

BRITELINE GEN2 1 Versatile and Efficient Lighting

PRODUCT OVERVIEW

BRITELINE GEN2 1				EXTERNAL GEAR BOX
A	B	C		D	E	F	G	H
609mm 23.97in	332mm 13.07in	436mm 17.16in	16.5kg 36.371bs	416mm 16.37in	372mm 14.64in	221mm 8.7in	205mm 8.07in	121mm 4.76in	6.2kg 13.6lbs

EPA – Effective Projected Area

	a = 0°			a = 30°			a = 45°			a = 70°			a = 90°
	S(m²)	CxS (m²)	EPA (ft²)	S(m²)	CxS (m²)	EPA (ft²)	S(m²)	CxS (m²)	EPA (ft²)	S(m²)	CxS (m²)	EPA (ft²)	S(m²)	CxS (m²)	EPA (ft²)
S1	0.057	0.07	0.74	0.0951	0.12	1.23	0.1100	0.14	1.43	0.1339	0.17	1.73	0.1406	0.17	1.82
S2	0.1406	0.17	2.	0.1382	0.17	1.79	0.1258	0.16	1.63	0.0920	0.12	1.19	0.0570	0.07	0.74
S3	0.0355	0.05	0.46	0.0355	0.05	0.46	0.0355	0.05	0.46	0.0355	0.05	0.46	0.0355	0.05	0.46

MOUNTING

Screws and washers are not included in the package!Minimum screw requirement:

Vibration standard	IEC 0.5g / ANSI 1.5g
Minimum fastener  requirement	1x M20 8.8 or A2-70 DIN9021 large plain washer
Tightening torques	1xM20: 200 Nm 2xM20: 140 Nm

Recommended to use anti-seizing agent (Tikal Tef-Gel®) !

1. 1xM20 with extra large washer or 2. 2xM20 with extra large washer

Mounting dimensions

D1	D2	D3	D4	D5
min 250mm min 9.84in	70mm 2.75in	150mm 5.9in	320mm 12,6in	460mm 15.98in

Minimum Surface Contact Area for screw fixation
Fasteners are not included in the package!
Remark: the hatched area always need to be supported by a flat planar mounting surface as minimum.
Wider surface contact is recommended, smaller is not allowed!

ANGLE ADJUSTMENT

1. Loosen the clamp screws
2. Adjust tilting angle
   Separate scale for adjusting the distance of the optical block from the luminaire holderThe swing arm inclination is adjustablein 10 degree increments relative to fork base.
   ALLOWED tilt angle is between -10° to 90°
3. Tighten the clamp screws Do not exceed the proposed torque levels, as it may result in fraction of the parts!

ALLOWED POSITIONING

GEAR INSTALLATION

SAFETY CABLE

Steel safety cable should pass through the holes shown in the drawing in sequence.
Then connect the two ends with the lock and tighten the lock screw by hand.
For installations over 3m height: secondary safety system application is mandatory, which is appropriated for the luminaire load (e.g. safety cable)
1500mm/59.05in safety cable is supplied with the luminaire.

ELECTRICAL CONNECTION

1. Remove the R-type buckles from the junction box and gear box
2. Open junction box and gear box
   

   Cable ID	Connection	Cable gland	Suitable cable Ø
   A	Mains input	M20	Ø6-10mm or Ø10-14mm
   B	Mains re-launch
   C	DC output to optical block	M25/cable ptorection compatibility	Ø6-10mm or Ø10-14mm
   D	Dimming input	M16	Ø4.5-7.5mm or Ø7.5-10.5mm
   E	Dimming re-launch

3. Cable types and cable gland
   When using a larger external diameter cable, the plug and the smaller inner diameter seal need to be removed
   When using a smaller external diameter cable, simply remove the plug
4. Make electrical connection
   Wiring should strictly follow the marking label instruction, otherwise the product could be damaged or the functions could be affected.
5. Close junction box and gear box
   Close the cover of the junction box and gear box, and put the R-type buckles back on both.

RECOMMENDATIONS

1. Surrounding distances At least 1 meter distance should be kept from surrounding walls, floor, and ceiling for all types of mounting/inclination.
2. Maximum number of luminaires per MCB
   

   Product	Driver	MCB B type
   		B10	B13	B16	B20	B25	B32	B40
   BRITELINE GEN2 1 ©220V	EUM-680MG/BG	1	2	2	3	4	5	6
   BRITELINE GEN2 1 ©480V	ESM-680MG/BG	2	2	3	4	5	6	7
   Product	Driver	MCB C type
   		C10	13	16	C20	C25	C32	C40
   BRITELINE GEN2 1 ©220V	EUM-680MG/BG	1	2	3	3	4	5	6
   BRITELINE GEN2 1 ©480V	ESM-680MG/BG	3	4	5	7	9	11	14

AIMING DEVICE

The small blocks on the side of the optical block assure the installation of the built-in aiming devide.
The external aiming device position 1 needs to be aligned with positions 2 and 3

ACCESSORIES – HOOD

SAFETY INSTRUCTIONS
The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person. Always switch off the power prior to installation, maintenance or repair activities.
RISK GROUP 2 – CAUTION! Hazardous optical radiation may be emitted from this product. Do not stare at the luminaire when operating as it may be harmful to the eyes. The luminaire should be positioned so that prolonged staring at the luminaire at a distance of less than 0.2m is not expected.
This product contains a light source of an energy efficiency class G or higher.
In case of PVC insulated mains cable, the installer MUST ensure that the WHOLE cable is protected against climatic conditions, especially UV rays and rain, by making sure that the cable is contained inside the luminaire and pole Y-connection: In case of damage to the wire, it has to be replaced only by the manufacturer, distributor or by an expert, to avoid risks.

www.schreder.com
Rev B | 07-2023

Documents / Resources

Schreder BRITELINE GEN2 1 Versatile and Efficient Lighting [pdf] Instruction Manual BRITELINE GEN2 1 Versatile and Efficient Lighting, BRITELINE GEN2 1, Versatile and Efficient Lighting, Efficient Lighting, Lighting

References

• User Manual