scheppach HL2550GM Metre Log Splitter

https://www.scheppach.com/de/service

Explanation of the symbols on the device

Symbols are used in this manual to draw your attention to potential hazards. The safety symbols and the accompanying explanations must be fully understood. The warnings themselves will not rectify a hazard and cannot replace proper accident prevention measures.

Introduction

Manufacturer:
Scheppach GmbH
Günzburger Straße 69
D-89335 Ichenhausen

Dear Customer
We hope your new device brings you much enjoyment and success.

Note:
In accordance with the applicable product liability laws, the manufacturer of this device assumes no liability for damage to the device or caused by the device arising from:

• Improper handling
• Failure to comply with the operating instructions.
• Repairs carried out by third parties, unauthorised specialists
• Installing and replacing non-original spare parts
• Improper use
• Failure of the electrical system in the event of the electrical regulations and VDE provisions 0100, DIN 57113 / VDE 0113 not being observed

Note:
The operating manual is part of this product. It includes important instructions for the safe, proper and economic operation of the product, for avoiding danger, for minimising repair costs and downtimes and for increasing the reliability and extending the service life of the product. In addition to the safety instructions in this operating manual, you must also observe the regulations applicable to the operation of the product in your country. Familiarise yourself with all operating and safety instructions before using the product. Only operate the product as described and for the specified areas of application. Keep the operating manual in a good place and hand over all documents when passing the product on to third parties.

Device Description

1. Cylinder
2. Control handle
3. Additional transport wheel
4. Engine
5. Chain
6. Trunk lifter
7. Cardan shaft protective cap
8. Three-point mounting
9. Transport wheels
10. Return lever
11. Riving knife
12. Combination switch/plug
13. Retainer arm
14. Support plate
15. Cardan shaft end firewood splitter
16. Drive vehicle cardan shaft end
17. Oil filling opening
18. Sight glass
19. Oil drain screw

Scope of delivery

• A. Splitter
• B. Retainer arm
• C. Trunk lifter
• D. Retainer hook
• E. Cardan shaft protective cap
• F. Accessory bag (a,b,c,d,e,f)
• G. Additional transport wheel
• H. Operating manual

Proper use

• The machine may only be used in the intended manner. Any use beyond this is improper. The user/operator, not the manufacturer, is responsible for damages or injuries of any type resulting from this.
• An element of the intended use is also the observance of the safety instructions, as well as the assembly instructions and operating information in the operating manual.
• Persons who operate and maintain the machine must be familiar with it and must be informed about potential dangers.
• In addition, the applicable accident prevention regulations must be strictly observed.
• Other general occupational health and safety related rules and regulations must be observed.
• The liability of the manufacturer and resulting damages are excluded in the event of modifications of the machine.
  • The hydraulic log splitter can only be used when standing and timbers may only be split in the direction of the grain.
  • Never split wood horizontally or against the grain.
  • The manufacturer’s safety, operating and maintenance specifications as well as the dimensions given in the technical data must be observed.
  • Relevant accident prevention regulations and other generally recognized safety and technical rules must also be observed.
  • The machine may only be used, maintained or repaired by persons who are familiar with it and have been informed of the dangers. The manufacturer shall not be liable for damage resulting from unauthorized changes to the machine.
  • The machine may only be operated with original accessories and original tools from the manufacturer.
  • Any use beyond this is improper use. The manufacturer is not responsible for the resulting damages; the user solely bears the risk.
• Please note that our equipment was not designed with the intention of use for commercial or industrial purposes. We assume no guarantee if the device is used in commercial or industrial applications, or for equivalent work.

General safety instructions

WARNING: When using power tools, the basic safety precautions below must be followed in order to reduce the risk of fire, electric shock, and personal injury. Please read all instructions before working with this tool.

• Observe all safety information and danger notices on the machine.
• Ensure that all of the safety information and danger notices on the machine are complete and in legible condition.
• The safety equipment on the machine must not be disassembled or made unusable.
• The safety equipment on the machine must not be disassembled or made unusable.
• Check mains connection cables. Do not use faulty connection cables.
• Check for correct function of the two-hand control before commissioning.
• The operating personnel must be at least 18 years of age. Trainees must be at least 16 years of age and may only work on the machine under supervision.
• Wear work gloves when working.
• Caution when working: Danger of injury for fingers and hands due to the splitting tool.
• Use suitable aids to support the splitting of heavy or bulky parts.
• Modification, adjustment and cleaning work, as well as maintenance and rectification of faults may only be carried out when the engine is switched off. Pull out the mains plug!
• Installation, repairs and maintenance work on the electrical equipment may only be carried out by electricians.
• All protective and safety equipment must be reassembled immediately after repair, maintenance is completed.
• Switch off the engine when leaving the workstation. Pull out the mains plug!

Additional safety instructions

• The log splitter may only be operated by a single person.
• Wear protective equipment (safety goggles/visor, gloves, safety shoes) to safeguard yourself against possible injury.
• Never split trunks that contain nails, wire or other objects.
• Wood that has already been split and wood chippings create a hazardous work area. There is a danger of tripping, slipping or falling. Always keep the work area orderly.
• Never place your hands on moving parts of the machine when it is switched on.
• Only split wood with a maximum length of 110 cm.

Warning! This power tool generates an electromagnetic field during operation. This field can impair active or passive medical implants under certain circumstances. In order to prevent the risk of serious or deadly injuries, we recommend that persons with medical implants consult with their physician and the manufacturer of the medical implant prior to operating the power tool.

Residual risks
The machine has been built according to the state-of-the-art and recognized technical safety requirements. However, individual residual risks can arise during operation.

• Danger of injury for fingers and hands from the splitting tool in the event of improper guiding or support of the wood.
• Injuries due to the workpiece being ejected at high speed due to improper holding or guiding.
• Hazard due to electrical power with the use of improper electrical connection cables.
• Furthermore, despite all precautions having been met, some non-obvious residual risks may still remain.
• Residual risks can be minimized if the “Safety instructions” and the “Proper use” are observed along with the whole of the operating instructions.
• Health hazards due to electrical power, with the use of improper electrical connection cables.
• Before performing setting or maintenance work, release the start button and pull out the mains plug.
• Avoid accidental starting of the machine: the operating button may not be pressed when inserting the plug in an outlet.
• Use the tool that is recommended in this operating manual. This is how to ensure that your machine provides optimum performance.
• Keep your hands away from the working area when the machine is in operation.

Technical data

• Drive PTO shaft + Electric motor
• Motor V / Hz 400 V / 50 Hz
• Rated input P1 5100 W
• Power output P2 4000 W
• Operating mode S6 40%
• PTO / motor speed rpm 540 1400
• Phase inverter yes
• Dimensions L x W x H 1540 x 1140 x 2520 mm
• Wood length min. – max. 560 – 1100 mm
• Wood diameter min. – max. 80 – 350 mm
• Power (t) Max. 25
• Cylinder stroke 948 mm
• Feed speed cm/s 10.5
• Return speed cm/s 7.5
• Oil quantity l 24
• Weight kg 319

Subject to technical changes!

Unpacking

• Open the packaging and carefully remove the device. Remove the packaging material, as well as the packaging and transport safety devices (if present). Check whether the scope of delivery is complete. Check the device and accessory parts for transport damage.
• In the event of complaints, the carrier must be informed immediately. Later claims will not be recognized.
• If possible, keep the packaging until the expiry of the warranty period.
• Familiarise yourself with the device by means of the operating manual before using for the first time. With accessories as well as wearing parts and replacement parts use only original parts. Spare parts can be obtained from your specialist dealer.
• When ordering please provide our article number as well as type and year of manufacture for your equipment.

ATTENTION!
The device and the packaging material are not children’s toys! Do not let children play with plastic bags, films or small parts! There is a danger of choking or suffocating!

Assembly / Before commissioning

1. Fitting the three-point bolts (Accessory bag
   A) (Fig. 3)
   
   Insert the threaded bolts through the holes provided and fix each one from the other side with an M22 nut.
2. Fitting the cardan shaft sleeve (7) (Accessory bag B)
   (Fig. 4)
   
   Place the cardan shaft protective cover on the protruding grub screws on the cardan shaft and secure it with the two M10 nuts.
3. Bringing the splitter into working position
   (Accessory bag C) (Fig. 5 + 6)
   
   Connect the splitter to the mains. Observe the rotational direction of the motor. Lower the two control handles until the cylinder latches into the guide. Insert the two Lpins (C) to secure the cylinder to the firewood splitter. Secure the Lpins in the spring lugs.
   After that, drive the splitting blade to the top position and remove the support.
   Keep the prop in a good place as it will be needed for transporting the splitter.
4. Fitting the retaining arm (13) (Accessory bag
   D) (Fig. 7)
   
   Secure the retaining arm with an M10x40 hexagon screw, two washers and a nut
5. Fitting the retaining hook (D) (Accessory bag E)
   (Fig. 8)
   
   Attach the retaining hook to the frame with 2 hexagon screws and 2 nuts.
6. Fitting the trunk lifter (accessory bag F)
   (Fig.9)
   
   Fasten the trunk lifter to the retaining lug with a hexagon screw M16x100. Attach the chain to the splitting blade.

Fitting an additional transport wheel (Fig. 10)

Attach the transport wheel as shown in Fig. 10. Fix the wheel in the upper hole with the locking pin (10a) when working with the splitter. Fix the wheel in the lower hole during transport.

ATTENTION!
Always make sure the device is fully assembled before commissioning!

Start-up

Make sure that the machine is installed completely and properly. Before each use, always check:

• the connection cables for defective areas (cracks, cuts and the like),
• The machine for possible damage,
• Whether all screws are tightened,
• The hydraulics for leaks and
• The oil level

Check the oil level (fig. 13)

The hydraulic system is a closed system with an oil tank, oil pump and control valve. Check the oil level regularly before commissioning. An oil level that is too low can damage the oil pump. The oil level must be within the middle mark on the oil dipstick. The splitting column must be retracted before the check, the machine must be level. Screw in the oil dipstick fully, to measure the oil level.

E-Motor

• Check the running direction of the motor. If the splitting arm is not in the upper position, move the splitting blade to the upper position using the return bow or handles. If the splitting arm is already in the top position, activate the splitting mechanism by moving the two levers downwards.
• This moves the splitting arm downwards.
• If the splitting blade does not move despite actuating the handles or the return bow, switch off the machine immediately. Turn the pole reversing unit in the plugin unit (Fig. 11 + 12) to change the direction of rotation of the motor.
  

Never allow the motor to run with the wrong direction of rotation! This will inevitably lead to the destruction of the pump system and no warranty claim can be made for this.

Functional check
Carry out a functional check before each use.

Attention!
Loosen the filler plug (Fig. 19) before commissioning.

Never forget to loosen the filler plug! Otherwise, the air in the system will be repeatedly compressed and depressurized, which will destroy the seals of the hydraulic circuit and the log splitter will no longer be usable. In this case, the seller and the manufacturer disassociate themselves from any warranty claims.

Switching on/off (12)

• Press the green button to switch on.
• Press the red button to switch off.
• Note: Before each use, always check the function of the on-off unit by switching it on and off once.

Restart protection in the event of a power interruption (zero-voltage release)
In the event of a power failure, unintentional unplugging of the plug or a defective fuse, the device switches off automatically. To switch it back on again, press the green button on the switch unit again.

Cardan shaft

• Before connecting the machine to the three-point hitch of the drive vehicle, ensure that the weight of the machine is suitable for the drive vehicle. The weight of the machine can be found on the manu-facturer’s rating plate.
• The cardan shaft may only be connected when the tractor engine is switched off.
• Only use approved cardan shafts that are suitable for use with the log splitter. The cardan shaft must also be equipped with all safety devices, which must be in good condition.
• Do not stand near the cardan shaft when it is in operation.
• Ensure that the speed on the tractor does not exceed the number specified on the rating plate, max. 540 rpm.
• Before carrying out maintenance work or if the riving knife has become jammed, first disconnect the machine from the tractor and switch off the tractor.

Attaching splitter to drive vehicle Fig. 13 + 14

1. Drive the drive vehicle backwards to the log splitter. Position the lower mounting arms close enough to the mounting pins of the firewood splitter.
2. Apply the parking brake of the drive vehicle and switch off the engine. Block the rear wheels on both sides with wedges or other suitable objects.
3. Remove the dust cover (1) and attach it to the cardan shaft protective cover (2)
4. Lower the lower mounting arms to the support pins of the firewood processor and secure them with the locking pins. (3)
5. Position the upper mounting arm in the bracket and align it with the holes in the bracket. Insert the hanger pin to lock the upper mounting arm.
   1. The cardan shaft end of the gearbox has a diameter of 34.8 mm and a connection with 6 teeth (standard category 1 cardan).
6. Slide the cardan drive shaft over the cardan shaft end on the gearbox and on the drive vehicle. Press in the spring pins located at both ends of the cardan shaft drive. Push the drive shaft further over the ends of the cardan shaft until the spring pins spring out and engage in the teeth of the end of the cardan shaft.
7. Align the cardan shaft Viewed from above and from the side of the shaft, the cardan shaft end on the firewood splitter (15) and the cardan shaft end on the drive vehicle (16) must be aligned parallel. The angles of the universal joints (α) must be as small as possible.
8. Secure the safety chain of the cardan shaft drive to a fixed part of the firewood processor and the drive vehicle to prevent the protective device from turning.
   Check the running direction of the drive vehicle’s cardan shaft. If the splitting arm is not in the upper position, move the splitting blade to the upper position using the return bow or handles. If the splitting arm is already in the top position, activate the splitting mechanism by moving the two levers downwards. This moves the splitting arm downwards. If the splitting blade does not move despite actuating the handles or the return bow, stop the cardan shaft drive and change its direction of rotation.

Never allow the cardan shaft drive to run with the wrong direction of rotation! This will inevitably lead to the destruction of the pump system and no warranty claim can be made for this.

Using the guard arm (Fig. 15)

The height of the guard arm can be set at various stages to suit the length of the wood.

Splitting (Fig. 16 + 17)

• If the outside temperature is below 5°C, allow the machine to idle for approx. five minutes so that the hydraulic system reaches operating temperature. Stand the wood upright under the splitting blade Attention: The splitting blade is very sharp. Danger of injury!
• When you press both adjustment levers down, the splitting blade moves downwards and splits the wood.
• Only split logs that have been sawn off straight.
• Split wood vertically.
• Never split horizontally or across the grain!
• Wear suitable gloves and safety shoes when splitting wood.
• If the wood is extremely overgrown, split the trunks from the outline.
  Attention: Certain types of wood can come under a lot of tension during splitting and crack abruptly.
• Pull out jammed wood against the splitting direction or remove it by moving the riving knife upwards. Attention: Danger of injury.

Operation of the trunk lifter (6)
General information about the trunk lifter:

• The chain of the trunk lifter may only be attached to the splitting blade using the last link for safety reasons.
• Ensure that no other people are present in the working range of the trunk lifter.

Operation of the trunk lifter:

• Release the retaining hook of the trunk lifter so that the lifting tube can run freely.
• Move the splitting blade down until the lifting tube of the trunk lifter lies completely on the floor.
• In this position, you can roll the trunk to the split onto the lifting tube
  (The trunk must lie in the area between the two fixing points)
• Push the return bow down and let the splitting blade move up.
  (Caution! Do not stand in the working range of the trunk lifter! Danger of injury!)
• Now align the trunk, press it against the holding mandrel and split it
  (Refer to: Working instructions)
• Then remove the split wood and move the riving knife and thus the trunk lifter down again.
• A new log can now be rolled onto the trunk lifter.

Resetting the trunk lifter.
This is used as a second guard arm when not using the trunk lifter. To do this, the arm is raised until it engages on the retaining hook.

Transport position of the trunk lifter:
Guide the trunk lifter up by hand until it latches into place.
Observe these instructions to ensure that you can work quickly and safely

Electrical connection

The electrical motor installed is connected and ready for operation. The connection complies with the applicable VDE and DIN provisions.
The customer’s mains connection as well as the extension cable used must also comply with these regulations.

Damaged electrical connection cable
The insulation on electrical connection cables is often damaged.

This may have the following causes:

• Pressure points, where connection cables are passed through windows or doors.
• Kinks where the connection cable has been improperly fastened or routed.
• Places where the connection cables have been cut due to being driven over.
• Insulation damage due to being ripped out of the wall outlet.
• Cracks due to the insulation ageing.
• Such damaged electrical connection cables must not be used and are life-threatening due to the insulation damage.
• Check the electrical connection cables for damage regularly. Ensure that the connection cables are disconnected from electrical power when checking for damage.
• Electrical connection cables must comply with the applicable VDE and DIN provisions. Only use connection cables with the designation H07RN.
• The printing of the type designation on the connection cable is mandatory.
• For singlephase AC motors, we recommend a fuse rating of C 16A or K 16A for machines with a high starting current (from 3000 watts)!

3-phase motor 400 V / 50 Hz
Mains voltage 400 Volt / 50 Hz.
Mains power connection and extension leads must be 5-core = 3 P + N + SL. – (3/N/PE).
Extension cables must have a minimum cross-section of 1.5mm².
The mains power connection must be protected with a max. 16 A fuse
When connecting to the mains or in the event of the machine being moved to another location, the turning direction must be checked. It may be necessary to change the polarity.
Turn the polechanging device in the device connector.

Cleaning

Attention!

• Disconnect the mains plug before carrying out any cleaning work.
• We recommend that you clean the device directly after every use.
• Wipe swarf and dust off the machine from time to time with a cloth.
• Clean the device at regular intervals using a damp cloth and a little soft soap. Do not use any cleaning products or solvents; they could attack the plastic parts of the device. Make sure that no water can penetrate the device interior.

Transport

• The firewood splitter can be easily transported using the 3-point attachment on the drive vehicle.
• Before transporting the firewood splitter, place it in the transport position. To do this, move the riving knife downwards until it rests on the metal support. Then remove both Lpins and move the hydraulic cylinder down into the transport position by pressing the return bow downwards.
• Make sure there is sufficient maneuvering space when driving, e.g. when turning, parking and at junctions.
• Before transport, ensure that the firewood splitter is properly and securely attached to the drive vehicle and that the cardan shaft has been disassembled.

Never transport the firewood splitter with the cardan shaft drive connected.
Make sure that the firewood splitter is raised high enough to pass obstacles during transport.

Storage

• Store the device and its accessories in a dark, dry and frost-free place that is inaccessible to children. The optimum storage temperature lies between 5 and 30 ˚C.
• Store the tool in its original packaging.
• Cover the tool to protect it from dust or moisture. Store the operating manual with the tool.

Maintenance

Attention!
Disconnect the mains plug before carrying out any maintenance work. Ensure that the cardan shaft is not connected to the drive vehicle.

When do I change the oil?
Initial oil change after 50 operating hours, then every 250 operating hours.

Oil change (Fig. 18)

• Place the firewood splitter on a slightly raised surface (e.g. Euro pallet). Set a sufficient container (min. 30 litres) under the drain screw on the splitting column. Open the drain screw and carefully allow the oil to run into the container.
• Open the filler plug on the top of the splitting column so that the oil can drain off better.
• Reinsert the drain screw with seal and tighten securely.
• Top up with new hydraulic oil. (contents: see technical data) and check the oil level with the oil dipstick. After changing the oil, operate the firewood splitter several times without actually splitting.

Attention! Do not allow any dirt particles to enter the oil container.
Dispose of the used oil properly at a local used oil collection point. Dumping used oil in the soil or mixing it with waste is prohibited.
We recommend oil from the HLP 32 range.

Changing the gearbox oil Fig. 20

The gearbox is filled with SAE90 gear oil at the factory. Drain the gear oil after the first 50 operating hours and replace it with new oil as specified. The next oil change should then be carried out every 250 operat-ing hours or every six months, whichever comes first.

1. Disassemble the cardan shaft protective cover and set a sufficiently large container under the gearbox.
2. First open the oil drain screw (19) and then the oil filler opening (17) and drain the oil completely.
3. Close the oil drain screw with a new seal and fill new SAE90 gear oil into the filler opening using a funnel until the lower edge of the sight glass (18) is almost covered with oil.

Check the oil level every 8 hours. The oil level is correct when the lower edge of the sight glass (18) is almost covered with oil.

Hydraulic system
The hydraulic system is a closed system with an oil tank, oil pump and control valve.
The factory-completed system must not be changed or tampered with.

Check the oil level regularly.
An oil level that is too low will damage the oil pump, Regularly check hydraulic connections and screw connections for leaks – retighten if necessary.

Connections and repairs
Connections and repair work on the electrical equipment may only be carried out by electricians.

Please provide the following information in the event of any inquiries:

• Type of current for the motor
• Machine datatype plate
• Motor datatype plate

Service Information
With this product, it is necessary to note that the following parts are subject to natural or usagerelated wear, or that the following parts are required as consumables.

Wearing parts: Riving knife / riving spar guides, hydraulic oil, gear oil may not be included in the scope of delivery!
Spare parts and accessories can be obtained from our Service Centre. To do this, scan the QR code on the front.

https://www.scheppach.com/de/service

Disposal and recycling

Notes for packaging

The packaging materials are recyclable. Please dispose of packaging in an environmentally friendly manner.

Notes on the electrical and electronic equipment act (ElektroG)

Waste electrical and electronic equipment does not belong in household waste, but must be collected and disposed of separately!

• Used batteries or rechargeable batteries that are not installed permanently in the old device must be removed non-destructively before disposal! Their disposal is regulated by the Battery Act.
• Owners or users of electrical and electronic devices are legally obliged to return them after use.
• The end user is responsible for deleting their personal data from the old device being disposed of!
• The symbol of the crossed-out dustbin means that waste electrical and electronic equipment must not be disposed of with household waste.
• Waste electrical and electronic equipment can be handed in free of charge at the following places:
  • Public disposal or collection points (e.g. municipal works yards)
  • Points of sale of electrical appliances (stationary and online), provided that dealers are obliged to take them back or offer to do so voluntarily.
  • Up to three waste electrical devices per type of device, with an edge length of no more than 25 centimeters, can be returned free of charge to the manufacturer without prior purchase of a new device from the manufacturer or taken to another authorized collection point in your vicinity.
  • Further supplementary take-back conditions of the manufacturers and distributors can be obtained from the respective customer service.
• If the manufacturer delivers a new electrical device to a private household, the manufacturer can arrange for the free collection of the old electrical device upon request from the end user. Please contact the manufacturer’s customer service for this.
• These statements only apply to devices installed and sold in the countries of the European Union and which are subject to the European Directive 2012/19/EU. In countries outside the European Union, different regulations may apply to the disposal of waste electrical and electronic equipment.

You can find out how to dispose of the disused device from your local authority or city administration.

Fuels and oils

• Before disposing of the device, the fuel tank and the motor oil tank must be emptied!
• Fuel and engine oil do not belong in household waste or drains, but must be collected or disposed of separately!
• Empty oil and fuel tanks must be disposed of in an environmentally friendly manner.

Troubleshooting

The following table shows fault symptoms and describes remedial measures in the event of your machine failing to work properly. If you cannot localise and rectify the problem with this, please contact your service workshop.

PARTS

EU Declaration of Conformity

hereby declares the following conformity under the EU Directive and standards for the following article

• Brand: SCHEPPACH
• Art.-Bezeichnung METERHOLZSPALTER -HL2550GM
• Article name: METRE LOG SPLITTER – HL2550GM
• Art. no: 5905509917
  

Standard references:
EN 609-1:2017; EN IEC 55014-1:2021; EN IEC 61000-3-2:2019+A1; EN 61000-3-3:2013+A1; EN IEC 55014-2:2021

This declaration of conformity is issued under the sole responsibility of the manufacturer
The object of the declaration described above fulfills the regulations of the directive 2011/65/EU of the European Parliament and Council from 8th June 2011, on the restriction of the use of certain hazardous substances in electrical and electronic equipment.

Ichenhausen, 05.12.2023
Signature / Andreas Pecher / Head of Project Management

First CE: 2018
Subject to change without notice

Documents registrar: Andreas Pecher
Günzburger Str. 69, D-89335 Ichenhausen

Warranty

Apparent defects must be notified within 8 days from the receipt of the goods. Otherwise, the buyerís rights of claim due to such defects are invalidated. We guarantee for our machines in case of proper treatment for the time of the statutory warranty period from delivery in such a way that we replace any machine part free of charge which provably becomes unusable due to faulty material or defects of fabrication within such period of time. With respect to parts not manufactured by us we only warrant insofar as we are entitled to warranty claims against the upstream suppliers. The costs for the installation of the new parts shall be borne by the buyer. The cancellation of sale or the reduction of purchase price as well as any other claims for damages shall be excluded.

www.scheppach.com

Frequently Asked Questions

Q: What safety precautions should I follow when using the log splitter?

A: Ensure to wear safety shoes, work gloves, and a protective helmet. Do not smoke in the work area. Only operate the machine alone. Read the manual before use.

Q: What are the two operating speeds of the log splitter?

A: The log splitter has two operating speeds – low speed for full splitting force and high speed for reduced splitting force.

Documents / Resources

scheppach HL2550GM Metre Log Splitter [pdf] Installation Guide HL2550GM Metre Log Splitter, HL2550GM, Metre Log Splitter, Log Splitter

References

• User Manual