Sarmert-LOGO

Sarmert 2BM6KC1 c1 Dashcam C1 5K Dash Cam Built

Sarmert-2BM6KC1-c1-Dashcam-C1-5K-Dash-Cam-Built-PRODUCT

PACKAGE CONTENTS

Sarmert-2BM6KC1-c1-Dashcam-C1-5K-Dash-Cam-Built-FIG- (1)

SPECIFICATION

Sarmert-2BM6KC1-c1-Dashcam-C1-5K-Dash-Cam-Built-FIG- (2) Sarmert-2BM6KC1-c1-Dashcam-C1-5K-Dash-Cam-Built-FIG- (3)

UNIT STRUCTURE, APPEARANCE & BUTTONS

Sarmert-2BM6KC1-c1-Dashcam-C1-5K-Dash-Cam-Built-FIG- (4)

INSTALLATION

Install the C1 5K dash cam at the top of the front windshield. Remove any foreign matter and clean and dry the windshield before installation. The C1 5K dash cam comes with default settings, allowing you to start using it right out of the box without any adjustments. Remember to format the memory card before first-time use.

Sarmert-2BM6KC1-c1-Dashcam-C1-5K-Dash-Cam-Built-FIG- (5)

Start the vehicle generator, and do a bench test before officially installing the dash cam: connect the car charger to the cigarette lighter port and the C1 5K dash cam, connect the C1 5K dash cam, and insert the MicroSD card to ensure that the dash cam can work normally-

1. Installation Position: Most people will install their C1 5K dash cam next to the rearview mirror, on the opposite side of the driver. First, turn off the engine in a welHit and safe location, then remove the key.
2. Insert the microSD card into the microSD slot of the dash cam and format your SD card for the first time use.
3. Make sure to clean your windshield from dust particles and evaporated grease from the dashboard surface.
4. Then peel off the electrostatic sticker from the cellophane, transfer it to the place you want to stick it.

Sarmert-2BM6KC1-c1-Dashcam-C1-5K-Dash-Cam-Built-FIG- (6)

5. Eliminate the air bubbles on the static stickers. It is recommended to install the dash cam after standing still for half an hour to make the static stickers stronger. Then stick the GPS bracket on top of the electrostatic film.
6. Attach the C1 5K dash cam with the GPS mount. Set the camera lens to point forward to the center when installing it. We suggest angling the lens slightly downward (approximately 10° below horizontal) to achieve a 6:4 ratio of road to background in the recorded videos.
7. Use the power cord to connect the USB Port of the product to the car’s cigarette lighter socket.
8. Hide the cable inside the trim and use the included cable clips for additional support to organize the cable if needed so it does not interfere with the driver’s vision.
9. Start the engine and check if the product works properly.
10. The device will start up automatically and record as soon as power is supplied, and the device will save the last video file and power off automatically after cutting the power supply.

CAUTION
Make sure to remove the Plastic Lens Screen Protector from the lens before recording videos. Otherwise, your videos will look blurry and blocked. Do not remove the microSD card while the camera is turned ON. Otherwise, it may cause the memory card to be write protected and possible loss of data or damage your memory card. Remove/Insert the memory card only when the camera is turned OFF.

TURNING YOUR CAMERA ON/OFF

AUTO POWER ON/OFF
• Auto Power On: The Sarmert C1 5K Dash Cam is set to turn on and start recording by itself when it gets power, like when you start your car.
• Auto Power Off: The camera will automatically turn off a few seconds after it loses power, such as when you turn off your car.

A CAUTION
Some trucks and cars have a power outlet that stays on even when the vehicle is off. If this is the case for your vehicle, the auto on/off feature won’t work properly. Leaving the camera recording when the car is off can drain your battery, potentially causing starting issues next time. To avoid this, you have two options:
1. Nect your dash cam directly to your car’s fuse box using Sarmert’s 3-Lead Auto Trigger Hardwire Kit. You can purchase this kit at Sarmert store,
2. Connect your dash cam directly to your car’s fuse box using Sarmert’s 3-Lead Auto Trigger Hardwire Kit.

MANUAL POWER ON/OFF
• To turn the camera on manually, press the power button once.
• To turn it off manually, press and hold the power button for about 2-3 seconds.

NOTE
Make sure to insert the memory card before turning on the camera. Don’t insert or remove the memory card while the camera is on; only do this when it’s turned off.

Documents / Resources

Sarmert 2BM6KC1 c1 Dashcam C1 5K Dash Cam Built [pdf] User Manual
2BM6KC1, 2BM6KC1 c1, 2BM6KC1 c1 Dashcam C1 5K Dash Cam Built, 2BM6KC1 c1, Dashcam C1 5K Dash Cam Built, C1 5K Dash Cam Built, 5K Dash Cam Built, Dash Cam Built, Cam Built, Built

References

Leave a comment

Your email address will not be published. Required fields are marked *