SALUS CONTROLS IT800 WIFI Smart Thermostat
Specifications
- Model: IT800 WIFI
- Wireless ZigBee thermostat
- Controls pre-paired WZ600 Zigbee Wi-Fi Receiver with a single channel relay
- Acts as the network coordinator for device management
Introduction
The IT800 is a wireless ZigBee thermostat which controls the pre-paired WZ600 Zigbee Wi-Fi Receiver, which has a single channel relay. It is the coordinator of the network, allowing devices to join the network and managing them thereafter.
Product Compliance
This product complies with the essential requirements and other relevant provisions of Directives 2014/30/EU, 2014/35/EU, 2014/53/EU and 2015/863/EU. The full text of the EU Declaration of Conformity is available at the following internet address: www.saluslegal.com.
2405-2480MHz; <20dBm (Wifi)
Safety Information
Use in accordance with the regulations. Indoor use only. Keep your device completely dry. Installation must be Use in accordance with the regulations. Indoor use only. Keep your device completely dry. Installation must be
- Push button
- Rotating dial
- Heat/Cool Mode indicator
- RF status
- Battery status
- Temperature display
- Locked mode
- Schedule settings
- Mode setting/Optimum features
- Frost protection (Off mode)
Receiver buttons
- AUTO – Receiver operates in auto mode according to the thermostat.
- MANUAL – Receiver output is controlled by the On/0ff slide switch. (Manual ON can be disabled in the App)
- ON – When in Manual Mode, ON will turn the boiler on.
- OFF – When in Manual Mode, OFF will turn the boiler off.
- ZIGBEE – ZigBee network configuration
- WIFI – WiFi network configuration
Note: Press and hold 10s the ZigBee and WiFi buttons to perform the Factory Reset.
Receiver LEDs
Wiring diagram
Pairing Process
Note: The thermostat and the receiver arrive pre-paired from the factory.
First power up
(The thermostat is in Shutdown mode.)
Settings in Offline mode
- 2 – AU Schedule mode*
- 3 – M Manual mode
- 4 – OFF Frost protection mode
Note: To select modes short click on push button or auto select after 5 seconds.
*Default schedule in Offline mode
| 7 days (Monday to Sunday) | ||
| Program | Time | Temperature |
| 1 | 6:00 | 21 °C |
| 2 | 23:00 | 19 °C |
*Note: Custom schedule available only in app.
Change setpoint
Heating
Cooling
Note: The selection is validated either by short press the button or auto selection after 5 seconds.
Advanced menu – heat/cool modes
Advanced menu – RF signal
Advanced menu – Factory Reset
Installation in Online mode – using Bluetooth
Power on the device then follow these steps to gain control via the Salus Premium Lite app.
- This product must be used with the SALUS Premium Lite application on mobile or web by accessing the following link: eu.premium.salusconnect.io
Head Office:
- ALUS Controls
- Units 8-10, Northfield Business
- ark, Forge Way, Parkgate otherham, S60 ISD
- mail: sales@salus-tech.com
SALUS CONTROLS GMB,
Dieselstrasse 34, 63165
Mühlheim am Main,
Email: info@salus-controls.de
www.saluscontrols.com
SALUS Controls is a member of the Computime Group
Maintaining a policy of continuous product development SALUS Controls plc reserve the right to change specification, design and materials of products listed in this brochure without prior notice.
Frequently Asked Questions
- Q: How do I perform a factory reset on the IT800 thermostat?
A: To perform a factory reset, press and hold the ZigBee and WiFi buttons simultaneously for 10 seconds. - Q: What should I do if I lose the internet connection?
A: Ensure your internet connection is stable and try reconnecting the device to the network. - Q: Can I disable the Manual Mode via the App?
A: Yes, you can disable Manual Mode through the App settings.
Documents / Resources
 |
SALUS CONTROLS IT800 WIFI Smart Thermostat [pdf] Instruction Manual IT800, WZ600, IT800 WIFI Smart Thermostat, IT800, WIFI Smart Thermostat, Smart Thermostat, Thermostat |