OK Series Inner Modular Frame
“
Product Specifications:
- Product Name: OK Series Inner Modular Frame (TMK)
- Components:
- 2 Vertical Uprights
- 2 Horizontal Rails
- 4 Cage Nuts
- 8 Flanged Cage Nuts
- 12 M6 Washers
- 12 M6x16 Hex Screws
- Tools Required: Driver or Screwdriver, 10mm extended
socket
Product Usage Instructions:
Step 1: Assembling Vertical Uprights and Horizontal Rails
Place each vertical upright with their channel openings facing
each other against the horizontal rails.
Secure them with the specified hardware as shown in Figure
4.
Step 2: Attaching Fasteners to Vertical Uprights
Install the M6 hex screws and washers in each of the four
corners of the left and right vertical uprights as shown in Figure
5.
FAQ:
Q: What tools are required for installation?
A: You will need a Driver or Screwdriver, and a 10mm extended
socket.
Q: How many vertical uprights and horizontal rails are included
in the package?
A: The package includes 2 vertical uprights and 2 horizontal
rails.
Q: What size are the hex screws provided?
A: The package includes M6x16 Hex Screws.
“`
OK Series Inner modular frame (TMK) Guide
OK TMK BOM Item Qty Part Description
1 2 Vertical Uprights 2 2 Horizontal Rails 3 4 Cage Nut 4 8 Flanged Cage Nut 5 12 M6 Washer 6 12 M6x16 Hex Screw
Tools Required: Driver or Screwdriver, 10mm extended socket
Installation Instructions:
1. Cage Nut Installation · Top and Bottom Horizontal Rails · Insert the flanged cage nuts (Item 4) into the vertical square slots of the top and bottom horizontal rails (Item 2). · Place four flanged cage nuts per rail from the rear (Figure 2). · OKK Modular Rails · Insert two cage nuts (Item 3) per OKK top and bottom element modular rails (Figures 3 & 6). See below note. · Important: Position each cage nut in the third slot from the door opening to mount the TMK.
2. Horizontal Rail Assembly · Attach each horizontal rail (Item 2) to the OKK top and bottom elements previously installed cage nuts (Figure 3). · Use two M6 hex screws (Item 6) and M6 washers (Item 5) per rail. · Torque Specifications: 70 in-lbs per M6 screw. · Orientation Notes: · Top Rail: Use the wider rail – matches the singular modular rail system of the OKK top element. · Bottom Rail: Use the narrower rail – matches the double modular rail system of the OKK bottom element.
3. Vertical Upright Assembly · Attach left and right vertical uprights (Item 1) using four M6 hex screws and washers per upright. · Secure the uprights to the horizontal rails through the previously installed flanged cage nuts. See Figures 4 & 5. · Torque Specifications: 70 in-lbs per M6 screw. · Orientation Note: · Ensure the channel opening of the vertical uprights face internally (Figure 4, outlined in red).
1
Figure 1
4
2 Figure 2
(Bottom Horizontal Rail)
6 5
3
Figure 3
ok-tmk.pdf
Additional Details
1 Vertical Upright Detail: Place each vertical upright with their channel openings facing each other against the horizontal rails. Secure with the specified hardware (Figure 4).
Figure 4
Vertical Upright Fastener Detail: Install the M6 hex screws and washers in each of the four corners of the left and right vertical uprights as shown (Figure 5).
Figure 6
Figure 5
Cage Nut Detail: Insert the cage nut (Item 3), non-flange side away from the rail corners, at a 45° angle. Slide flush with the rail (Figure 6).
2
ok-tmk.pdf
Documents / Resources
 |
Saginaw Control OK Series Inner Modular Frame [pdf] User Guide OK Series Inner Modular Frame, OK Series, Inner Modular Frame, Modular Frame, Frame |