Standalone Access Control
User Manual
Introduction
The series of product is a new generation of multi-functional standalone access control. It adopts new ARM core 32-bit microprocessor design, which is powerful, stable and reliable. It contains reader mode and standalone access control mode etc.. It’s widely applied to different occasions, such as office, residential communities, villa etc..
Features
| Feature | Specification |
| Card Type | Read 125KHz EM Card and HID Card (Optional) |
| Read 13.56MHz Mifare card and CPU card (Optional) | |
| Keypad Characteristic | Operate by infrared remote |
| Output Way | Contain reader mode, the transmission format could be adjusted by users. |
| Access Way | Support multi access ways: Card, multi cards |
| Admin Card | Support admin card |
| User Capacity | 10,000 card users |
| Unlocking Signal | Relay NO/NC/COM output |
Technical Specifications
| Operating Voltage: DC 12-24V | Standby Current: 5. 35mA |
| Operating Current: 5100mA | Operating Temperature: -35°C-60°C |
| Operating Humidity: 0%-95% | Electric lock signal relay contact current: 51A |
| Alarm signal MOS tube output current: 51A | Unlocking time: 0-300s adjustable |
Installation
- Remove the back cover from the keypad using the supplied special screw driver
- Drill 2 holes on the wall for the self-tapping screws and hole for the cable
- Put the supplied rubber bungs to into the two holes
- Fix the back cover firmly on the wall with 2 self-tapping screws
- Thread the cable through the cable hole
- Attach the keypad to the back cover. (as following illustration)
Wiring
| No. | Color | Marks | Description |
| 1 | Green | DO | Wiegand input (Wiegand output as reader mode) |
| 2 | White | D1 | Wiegand input (Wiegand output as reader mode) |
| 3 | Yellow | OPEN! BEEP | Exit button input end (Beeper input as reader mode) |
| 4 | Red | +12V | Positive power supply |
| 5 | Black | GND | Negative power supply |
| 6 | Blue | NO | Relay NO end |
| 7 | Purple | COM | Relay COM end |
| 8 | Orange | NC | Relay NC end |
Diagram
6.1 Common Power Supply
6.2 Special Power Supply
6.3 Reader Mode
Sound and Light Indication
| Operation Status | Light indicator | Buzzer |
| Stand by | Red | |
| Operation successful | Green | Beep— |
| Operation failed | Beep-Beep-Beep | |
| Admin card enter programming | Beep-Beep | |
| Admin card exit programming | Beep— | |
| Press digital key | Beep | |
| Press * key | Beep— | |
| On process of reading multi user card | Red indicator flash slowly | |
| Enter programming mode | Red indicator flash slowly | |
| Enter setting status | Orange | |
| Unlocking | Green | |
| Buzzer alarm | Red indicator flash quickly | Alarm |
8.1 Standalone Mode Settings
Device Management
| Enter programming | Menu | Operation steps | Description | Default value |
| Press * Admin code # (Default admin code is “999999”) |
0 | New admin code # new admin code # | Change admin code | 999999 |
| 1 | 10001# Read card* | Set admin add card | ||
| 10002# Read card * | Set admin delete card | |||
| 2 | 10001# * | Delete admin add card | ||
| 10002# * | Delete admin delete card | |||
| 3 | 11 # | Standalone access control mode | 11 | |
| 12 # | Relay toggle mode | |||
| 13 # | Reader mode | |||
| ( 26-58 )# | Wiegand 26-58 bits output |
Add and Delete Users
| Enter programming | Menu | Operation steps | Description | Default value |
| Press * Admin code # (Default admin code is “999999”) |
1 | Read card … * | Add card users continuously | , `…” means repeating the previous operation, Press * key to exit. |
| Press 8 or 10 digits card number # … * | Add card users by card number | |||
| Press ID number # Read card … * | Add card users by specific ID number | |||
| Press ID number # Press 8 or 10 digits card number # | Add card users by specific ID number and card number | |||
| Delete users | ||||
| 2 | Read card… * | Delete card users by reading card | “…” means repeating the previous operation, Press * key to exit. | |
| Press 8 or 10 digits card number #… * | Delete card users by card number | |||
| Press ID number # … * | Delete users by ID number | |||
| 0000# | Delete ALL users | |||
Access Ways
| Enter programming | Menu | Operation steps | Description | Default value |
| Press *Admin code # (Default admin code is “999999”) | 3 | 0 # | Entry by card | 0 |
| 2-10 # | Entry by multi-card |
Advanced Settings
| Enter programming | Menu | Operation steps | Description | Default value |
| Press * Admin code # (Default admin code is “999999”) | 4 | (0-300) # | Door opening time range: 0-300S 0 equals to 50mS | 5 |
| 5 | (0-99) # | Alarming time range: 0-99 min. | 0 | |
| 7 | Press ID number # press 8 or 10 digits card number # input card quantity # | Add conductive number card | ||
| 8 | 0# | Normal working mode | 0 | |
| 1# | The external alarm and built-in buzzer will work if wrong operations are over 5 times. | |||
| 2# | The device will be locked out for 10 min if wrong operations are over 5 times. | |||
| 3# | Disable light indicator | 4 | ||
| 4# | Enable light indicator | |||
| 5# | Disable buzzer | 6 | ||
| 6# | Enable buzzer |
8.2 Reader Mode Settings
| Enter programming | Menu | Operation steps | Description | Default value |
| Press * Admin code # (Default admin code is “999999”) |
0 | New admin code # Repeat new admin code # | Change admin code | 999999 |
| 3 | (13) # | Reader Mode | ||
| (26-58) # | Wiegand 26-58 bits output | 26 |
Admin Operation
9.1 Add Users
Read admin add card | Read the 1″ usercard Read the 2“ usercard | Read admin add card
Note: The admin add card is used to add card continuously and quickly. When you read the admin add card at the first time, you will hear short “BEEP” sounds twice and the indicator light turns orange, it means you have entered into add user programming, when you read the admin add card at the second time, you will hear long “BEEP” sound once and the indicator light turns red, it means you have exited the add user programming.
9.2 Delete Users
Read admin delete card | Read the 1″ usercard Read the 2“ user card …. Read admin delete card
Note: The admin delete card is used to delete card continuously and quickly. When you read the admin delete card at the first time, you will hear short “BEEP” sounds twice and the indicator light turns orange, it means you have entered into delete user programming, when you read the admin delete card at the second time, you will hear long “BEEP” sound once, the indicator light turns red, it means you have exited the delete user programming.
Other Operation
10.1 Remove Alarm
Read valid card or Press admin code#
Note: When the alarm is activated, users can remove the alarm by reading a valid card or pressing valid admin code.
10.2 Reset to Factory Default
Users can reset to the factory default when the admin code is forgotten, or the default settings have been modified disorderedly, operations as below:
Power off, press and hold the exit button continuously, power on, release the exit button until hearing beep sound twice, the admin code has been reset to 999999, factory default settings are successful.
Note: Registered user data won’t be deleted when reset to factory default.
Documents / Resources
 |
safire AC105MF Standalone Access Control [pdf] User Manual AC105MF Standalone Access Control, AC105MF, Standalone Access Control, Access Control, Control |
