RW9-SSxx or RW9-DSxx Wireless Switch, RW9-5C-B 5A Receiver

“

Product Information

Specifications

Product: Kinetic On/Off Wireless Switch
Kits
Wireless Switch Models: RW9-SSxx or
RW9-DSxx

Range: 50-150 ft (typical)
Frequency: 902 MHz

Power Supply: Self-Generated when switch is
pressed
Output Channels: Link to any number of
receivers in range

Buttons: 2 Buttons – 1 Rocker (RW9-SSxx) or 4
Buttons – 2 Rockers (RW9-DSxx)
Addressing: Factory set unique ID (1 of 4
Billion)

Dimensions: 2.75(W) x 4.5(H) x 0.62(D)
inches
Radio Certification: FCC (United States)

Product Usage Instructions

Installing Receiver

Turn breaker OFF for the circuit you will be working on.
Access wires by removing the original switch or fixture.

Connect receiver wires:
- Black wire connects to Power In / Line wire
- Blue wire connects to Power Out / Load wire
- White wire connects to Neutral wire

Turn breaker ON to test the sensor, then back OFF prior to
tucking wires and receiver back into the junction box.

Mounting Wireless Switch

Option 1: Mount on Flat Surface / Remote

Use small screws to attach the switch to the backplate.

Press faceplate onto the switch, click into place.
Use command strips to mount on any flat surface, or use as a
remote.

Option 2: Mount at Wall Switch Location

Use large screws to attach the switch to the junction box.
Press faceplate onto the switch, or screw on
standard/multi-gang faceplate.

Backplate not needed.

Troubleshooting

Confirm Receiver is Wired Correctly: Test the
status light on the receiver by pressing the CTRL button. Green
means the output should be ON, no light means the output should be
OFF. If the status light is not working, that indicates the power
is not ON, wiring is incorrect, or the receiver has been damaged.
Try tapping the button a few times to get the light to turn on. If
the status light turns ON, but the light…

Frequently Asked Questions (FAQ)

Q: Can this product be used outdoors?

A: No, this product is intended for indoor use only.

Q: How many switches can be linked to a single receiver?

A: You can link up to 10 switches to a single receiver.

“`

View Fullscreen

INSTALLATION GUIDE
KINETIC ON/OFF WIRELESS SWITCH KITS

SPECIFICATIONS

WIRELESS SWITCH (RW9-SSxx of RW9-DSxx)

RANGE

50-150 ft (typical)

FREQUENCY

902 MHz

POWER SUPPLY

Self-Generated when switch is pressed

OUTPUT CHANNELS

Link to any number of receivers in range

BUTTONS

2 Buttons – 1 Rocker(RW9-SSxx) OR 4 Buttons – 2 Rockers (RW9-DSxx)

ADDRESSING

Factory set unique ID (1 of 4 Billion)

DIMENSIONS

2.75(W) x 4.5(H) x 0.62(D) inches

RADIO CERTIFICATION

FCC (United States)

INSTALLING RECEIVER
The receiver can be installed at the original switch location (if neutral wire is present) or light fixture. 1. Turn breaker OFF for circuit you will be working on
2. Access wires by removing original switch or fixture:

Wireless Switch

5A Receiver

RW9-SSxx or RW9-DSxx RW9-5C-B

5 AMP RECEIVER (RW9-5C-B)

RANGE

50-150 ft (typical)

SCAN FOR DIGITAL GUIDE & EXTRA TIPS/INFO Or Visit: runlesswire.com/install

PACKAGE CONTENTS

EQUIPMENT NEEDED

5A Receiver

Screw driver

Wireless Light Switch

Screwless Faceplate & Backplate

Hardware Kit: Mounting Screws & Wire Nuts

FREQUENCY

902 MHz

POWER SUPPLY INPUT RATING 100-240 VAC 50/60 Hz

RELAY OUTPUT

1 Form A Relay 5A

MAX LOADS / CONTACT RATINGS

Resistive Load 5A Tungsten 600W Fluorescent 600W LED Lamp 200W

MEMORY

Link up to 10 Switches

OPERATING TEMP

-40°F – 104° F (-40°C – 60°C)

SWITCH LOCATION

FIXTURE LOCATION

3. Connect receiver wires: a. Black wire connects to Power In / Line wire b. Blue wire connects to Power Out / Load wire c. White wire connects to Neutral wire

CAUTION This product is intended for use indoors and in dry
locations only. Install and use in accordance with these
instructions, electrical codes, and regulations. If you feel unsure or uncomfortable with any part
of these instructions, consult an electrician.

DIMENSIONS RADIO CERTIFICATION

1.6(W) x 3.3(H) x 1.1(L) inches FCC (United States)

1 of 2

AHD0729C

4. Turn breaker ON to test sensor, then back OFF prior to tucking wires and receiver back into junction box.
INSTALL AT SWITCH LOCATION: Cover with a blank faceplate, or mount wireless switch (see option 2 below). INSTALL AT FIXTURE LOCATION: Re-attach light fixture. Turn breaker back ON to use, and enjoy!

OPTION 2: MOUNT AT WALL SWITCH LOCATION 1. Use large screws to attach switch to junction box 2. Press faceplate onto switch, or screw on standard/multi-gang faceplace 3. Backplate not needed

TIPS FOR INSTALLATION: Neutral wires are normally white and will not be connected to
original switch, they are sometimes tucked back in the box. If neutral wires are not present at switch location, install receiver at fixture location. Ground wires are green or copper and not needed to install receiver. If present, leave alone or cap off with a wire nut. The line wire brings power from the breaker The load wire brings power from the fixture
MOUNTING WIRELESS SWITCH
OPTION 1: MOUNT ON FLAT SURFACE / REMOTE 1. Use small screws to attach switch to backplate 2. Press faceplate onto switch, click into place 3. Use command strips to mount on any flat surface, or use as a remote

FOR STANDARD OR MULTI-GANG FACEPLATES:

TROUBLESHOOTING
CONFIRM RECEIVER IS WIRED CORRECTLY: Test the status light on the receiver by pressing the CTRL button. Green means the output should be ON, no light means the output should be OFF. If the status light is not working, that indicates the power is not ON, wiring is incorrect, or the receiver has been damaged. Try tapping the button a few times to get the light to turn on. If the status light turns ON, but the light

doesn’t turn ON, the wiring could be incorrect or it could be a bulb failure. CONFIRM SWITCH IS FUNCTIONAL: Press the top of the switch to turn the receiver ON and the bottom of the switch to turn it OFF. If the receiver doesn’t respond, the switch may not be linked.
LINK/UNLINK SWITCH TO RECEIVER: ALL KITS COME PRE-LINKED, ONLY DO THIS TO ADD OR REMOVE SWITCHES OR RECEIVERS 1. Press button on receiver for 3 seconds until
receiver begins to toggle on/off. 2. Press TOP of switch 3 times quickly to link
switch to receiver, or BOTTOM of switch 3 times to unlink. 3. The LED and output will pause ON for 3 seconds if linked, or OFF for 3 seconds if unlinked. 4. Wait for linking mode to time out (30 seconds). 5. Test switch to ensure it’s linked properly.
FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for
compliance. Such modifications could void the user’s authority to operate the equipment.
Contact Us for Questions or Help:
support@runlesswire.com
866.600.2111

2 of 2