Ruko U11MINI Drones With Camera
Battery Features
- Balance Protection: Automatically balance the internal battery cell voltage to protect the battery.
- Overcharge Protection: Overcharge will seriously damage the battery.
- When the battery is full, remove the charger device in time.
- Over-discharge Protection: Over-discharge will seriously damage the battery. When the battery is not used for flight, the battery will automatically discharge to protect the battery life.
- Short Circuit Protection: When the battery detects a short circuit, the output will be cut off to protect the battery.
- Easy Charging: Use a standard 5V USB charger (Android-compatible) and avoid any charger exceeding 12V output.
- Please read carefully and strictly abide by Veeniix’s Requirements in this User Manual, Quick Start Guide. The stickers on the battery surface before using the battery.
- The user shall bear the consequences caused by failure to use it as required.
Install the intelligent flight battery into the battery compartment and push it down until you hear a “click” from the battery buckle, indicating that it pops up and locks. Make sure the battery is in place. To remove the battery, press the buckles on both sides of the battery and pull it out of the battery compartment.
Do not install the battery into the aircraft or remove the battery from the aircraft when the battery power is turned on. Otherwise, the poor contact of the battery interface during the operation may cause the battery to short-circuit and burn the aircraft. The battery must be installed or removed with the battery power turned off.
Powering Off
• Press and hold the power button until all lights are off and release
the power button. After closing, the indicators are off.
• Note: The drone has an automatic shutdown function. If there is
no operation (not being taken off), the drone will automatically
shut down after 10 minutes of being turned on.
Charging the Battery
• Before using the intelligent flight battery, be sure to fully charge it.
1. Please use a 5V/2A or 5V/3A USB charging plug.
2. In the charging state, the battery power indicator will flash and
indicate the current charge level; when the fourth indicator light is
always on, it indicates that the charging is complete.
3. After charging is complete, please remove the charger in time.3.8 Camera Overview
• The camera features an upgraded 5GHz Wi-Fi FPV real-time
transmission function, equipped with an 85° FOV lens, a 90°
adjustable camera, and a three-axis brushless gimbal for
stabilization. This setup allows for stable shooting of 4K HD video
and 8K ultra-clear images, providing you with a wide field of view
to fully enjoy unforgettable moments.
To
-90°
• The gimbal features a three-axis mechanical stabilization system,
EIS electronic stabilization, and axes for roll and pitch. The yaw
axis uses a brushless motor combined with ElS technology.
Roll Axis
Tilt Axis
Yaw Axis
• The gimbal will not operate and will remain tilted when it is
powered off or during compass calibration, which is normal. Once
powered on and calibration is complete, the gimbal will
automatically perform a self-check and enter working mode, taking
approximately 20 seconds to stabilize in a level position. Be careful
not to touch the drone during calibration.• The drone’s gimbal is a movable mechanical structure, and it
is normal for the gimbal to appear tilted when powered off.
• If the drone takes off from grass, the gimbal may fail the
self-check if it comes into contact with the grass. To avoid
this, use a launch pad or cardboard to prevent the gimbal from
hitting foreign objects.
• Taking off from a floor, roadside, or table may cause
vibrations that lead to gimbal self-check failures. Avoid using
the drone in areas that produce significant vibrations.
• External force interference or lifting the drone during
thecalibration process can cause the gimbal to fail the
self-check.The self-check takes about 20 seconds,so avoid
touching the drone during calibration.
• The gimbal will not work during compass calibration. Once the
calibration is complete, place the drone on a level surface, and
it will automatically enter working mode.
Storing Photos and Videos
• V11MINI 4K is equipped with a micro SD card slot for storage space
expansion.
1. Card speed: 10M/s.
2.File format: support FAT32 format.
3. Memory capacity: a memory card with a memory capacity of
256G or less.
• The mobile phone and the memory card store photos and videos at
the same time. If you want clearer videos, please download the
video file on the memory card.1. Check whether the capacity of the memory card is sufficient.
If the capacity of the memory card is insufficient, videos and
pictures cannot be stored.
2. If you cannot save pictures or videos, try formatting the
memory card.
3. After installing the memory card, all photo and video files will
be stored on the card instead of your mobile phone.
4. You must turn on the aircraft and connect App to copy or
download the photos or videos stored in the aircraft memory
card to the phone.
5. Please turn off the aircraft correctly, otherwise the camera
parameters will not be saved and the video being recorded will
be damaged. Veeniix is not responsible for any damage
caused by the inability to read videos and photos.
6. Do not touch the SD card slot directly with your hand during
use, and be cautious of high temperatures.
4 Remote Controller
4.1 Remote Controller Profile
• V11MINI 4K remote controller uses the 5 GHz frequency band. The
folding handle can stably place the mobile phone, and the
maximum adjustable width is 3.15 inches.
• Remote controller built-in 1500mAh capacity battery, charging time
is 80 minutes.• Note: Equipped with 3 different models of data cable, please
choose the data cable suitable for your phone to connect.
(The USB-C data cable is in the remote control, and the other two
are in the packaging box)
Please correctly set the USB Settings option that pops up. Select
“Transterring tiles” for Android phones, and “Trust” for iPhones.
Some USB Settings of Android phones are hidden in the “Developer
options”, you need to change the “Default USB configuration” to”
Transferring files” after opening the developer mode.
Powering On/Off
• Turn on the remote control: Press the power button for 3 seconds to
turn it on.
• Turn off the remote control: Press the power button for another 3
seconds to turn it off.
Charging the Controller Battery
• Connect the remote controller Micro USB interface to the charger
for charging. Do not use a fast charger that exceeds the rated
power. A 5V/2A or 5V/3A charger is recommended.
1. Charging: The four lights flash in turn.
2. Charging is completed: 4 indicators are on.
PD/QC 3.0
(Not Including)3. Ine drone and remote control will automatically complete the
requency pair, and the frequency alignment time is about 30
seconds.
4. Connect the mobile phone with the remote control to enter the
App control interface; The phone displays information such as the
power signal of the remote control and the camera screen indicates
that the frequency is successfully matched.
• The remote controller pairs with aircraft successfully:
1. The drone lights will change from red to green,
2. The green light of the remote control changes from blinking to
steady on.
• The drone and the remote control will automatically connect, the
connection time is about 30 seconds. Please check the remote
control power before each flight. The remote control will sound a
tone when the battery is low.
• The remote control will automatically shut down after being idle
for 10 minutes, and the remote control can be restored to normal
working state by flipping the joystick or pressing any key.
We suret press tighte to avoid the mobile de vice sile device.
• Keep the battery at around 7.8-7.9V, and recharge it every month
or so to keep the battery active.
Documents / Resources
 |
Ruko U11MINI Drones With Camera [pdf] User Manual 2BBLM-V11MINI4K, 2BBLMV11MINI4K, v11mini4k, U11MINI Drones With Camera, U11MINI, Drones With Camera, Camera |