1 Важная информация по безопасности
ПРЕДУПРЕЖДЕНИЕ: Failure to follow these safety instructions could result in serious injury or death. Always read and understand the full manual before operating the sprayer.
- Обеспечьте надлежащее электрическое заземление.
- Avoid contact with pressurized liquids.
- Use appropriate personal protective equipment (PPE) when handling chemicals, including eye protection, gloves, and respiratory protection.
- Maintain the device as instructed to prevent mechanical failure or injury.
- Никогда не направляйте распылитель на себя или других.
- Always relieve pressure before cleaning, servicing, or storing the unit.
2. Продукт закончилсяview
The Graco Ultra Max II 495 PC Pro is a professional-grade electric airless paint sprayer designed for high-performance painting applications. This Hi-Boy model offers enhanced portability and stability for various job sites.
Figure 1: Graco Ultra Max II 495 PC Pro Electric Airless Paint Sprayer. This image shows the complete sprayer unit, including the main pump, motor, hose, and spray gun, set up for operation.
Основные характеристики:
- SmartControl 3.0: Monitors performance, adjusts motor speed, measures sprayer gallons, hours, and pressure, and provides diagnostic support.
- BlueLink Job and Sprayer Management System: Enables tracking of sprayer usage, job progress, and maximizes uptime.
- MaxPower Brushless DC Motor: Delivers high torque and maintenance-free performance.
- FastFlush High-Flow Cleaning System: Allows for 4X faster cleaning with half the water.
- Hi-Boy Design: Provides easy transport and stability with a kickstand for convenient bucket changes.
3. Настройка и сборка
Before operating your Graco Ultra Max II 495 PC Pro, ensure all components are correctly assembled and connected.
3.1 Распаковка и осмотр
- Аккуратно извлеките все компоненты из упаковки.
- Проверьте товар на наличие повреждений при транспортировке. При обнаружении повреждений немедленно свяжитесь с вашим дилером.
- Убедитесь в наличии всех деталей, указанных в упаковочном листе.
3.2 Assembly (Hi-Boy Model)
- Attach the handle to the main unit using the provided hardware.
- Secure the hose and spray gun to the designated connections. Ensure all connections are tight to prevent leaks.
- Position the unit on a stable, level surface. The Hi-Boy design includes a kickstand for stability during bucket changes.
3.3 Подключение питания
- Connect the power cord to a properly grounded electrical outlet. Refer to local electrical codes for requirements.
- Ensure the power switch on the sprayer is in the "OFF" position before connecting to power.
3.4 Подготовка опрыскивателя к работе
- Place the suction tube into the paint container.
- Turn the prime valve to the "PRIME" position.
- Turn on the sprayer. Allow the unit to run until paint flows smoothly from the prime hose, indicating air has been purged from the system.
- Turn off the sprayer and return the prime valve to the "SPRAY" position.
4. Инструкция по эксплуатации
Proper operation ensures efficient and consistent paint application.
4.1 SmartControl 3.0 System
The SmartControl 3.0 system continuously monitors the sprayer's performance and adjusts the motor speed to match your spraying needs. This ensures a consistent spray pattern and finish. The display provides real-time information on:
- Sprayer gallons used
- Часы работы
- Current pressure settings
- Diagnostic support messages
4.2 BlueLink Job and Sprayer Management System
Utilize the BlueLink system to track your sprayer's activity and manage job progress. This feature helps maximize uptime by providing insights into usage and maintenance schedules.
4.3 Техника распыления
- Держите краскопульт перпендикулярно поверхности, поддерживая постоянное расстояние (обычно 10-12 дюймов).
- Begin moving your arm before pulling the trigger and release the trigger before stopping your arm movement.
- Для обеспечения равномерного покрытия перекрывайте каждый проход примерно на 50%.
- Adjust pressure settings on the SmartControl 3.0 as needed for different materials and desired finishes.
5. Техническое обслуживание и чистка
Regular maintenance and thorough cleaning are essential for extending the life of your Graco Ultra Max II 495 PC Pro and ensuring optimal performance.
5.1 FastFlush High-Flow Cleaning System
The FastFlush system allows for quick and efficient cleaning. Follow these steps:
- Relieve pressure from the system.
- Remove the suction tube from the paint and place it into a bucket of appropriate cleaning solution (water for latex, mineral spirits for oil-based paints).
- Turn the prime valve to the "CLEAN" or "FLUSH" position (refer to specific model instructions for exact valve position).
- Turn on the sprayer and allow the cleaning solution to circulate until it runs clear from the prime hose and spray gun.
- Turn off the sprayer and relieve pressure.
- Remove and clean the spray tip and guard separately.
5.2 Общее обслуживание
- Inspect hoses and connections regularly for wear or damage. Replace as needed.
- Check the spray tip for wear. A worn tip will result in a poor spray pattern and increased material consumption.
- The MaxPower Brushless DC Motor is designed for maintenance-free performance, but ensure it remains free of debris.
- Store the sprayer in a clean, dry environment, protected from freezing temperatures.
6. Поиск Неисправностей
This section provides solutions to common issues you may encounter during operation. For more complex problems, consult the full Graco service manual or contact customer support.
| Проблема | Возможная причина | Решение |
|---|---|---|
| Отсутствие распыления или низкое давление | Clogged tip, clogged filter, air in system, worn pump packings. | Clean tip/filters, re-prime unit, inspect/replace packings. |
| Пульсирующая струя | Air in system, loose suction tube, worn inlet valve. | Re-prime, tighten connections, inspect/replace inlet valve. |
| Poor spray pattern (tails) | Worn spray tip, incorrect pressure setting, material too thick. | Replace tip, adjust pressure, thin material if necessary (follow paint manufacturer guidelines). |
| Motor runs but no pressure builds | Inlet valve stuck open, prime valve in wrong position. | Clean/free inlet valve, ensure prime valve is in "SPRAY" position. |
The SmartControl 3.0 display may also provide specific diagnostic codes or messages to assist in troubleshooting.
7. Технические характеристики
| Особенность | Деталь |
|---|---|
| Бренд | Грако |
| Название модели | Ультра Макс II |
| Номер модели | 17E857 (ULTRA MAX II-495 PC PRO) |
| Источник питания | Электрический |
| Рекомендуемое использование | Рисование |
| Материал | Нержавеющая сталь |
| Цвет | Синий |
| Вес товара | 83.8 фунта |
| Размеры упаковки | 32.5 x 24.5 x 22 дюйма |
| Особые возможности | Безвоздушный |
| Батарейки в комплекте | Нет |
| Требуются батареи | Нет |
| Производитель | ГРАКО |
| СКП | 755652818694 |
8. Гарантия и поддержка клиентов
For detailed warranty information, please refer to the documentation included with your product or visit the official Graco website. Graco provides comprehensive customer support for all its products.
If you require assistance with setup, operation, maintenance, or troubleshooting beyond the scope of this manual, please contact Graco Customer Support directly. Contact information can typically be found on the product packaging or the manufacturer's webсайт.
