1. Меры предосторожности
ПРЕДУПРЕЖДЕНИЕ:
- Do not disassemble, short-circuit, charge, or heat the battery. Battery content may leak and come into contact with the eye, or cause battery heating or explosion.
- При проглатывании батареи немедленно обратитесь к врачу.
Экологическая утилизация:
This product should not be treated as household waste. Please reuse and recycle to reduce environmental impact. Contact your local dealer or distributors for proper disposal information.
2. Продукт закончилсяview и компоненты
The SHAHE IP54 Digital Vernier Caliper is designed for precise measurements in various applications. Below is a diagram illustrating its main components.
- Outside measuring faces
- Ступенчатое измерение граней
- Inside measuring faces
- переключатель дюймов/мм
- Clamp винт
- ЖК-дисплей
- Connector cap (for external output type only)
- Основная шкала
- Depth bar
- Thumb roller
- Крышка батарейного отсека
- Нулевой ключ
- Переключатель питания ВКЛ/ВЫКЛ
- Слайдер
3. Настройка
3.1 Установка аккумулятора
The caliper uses one 3V CR2032 environmental lithium battery (not included). To install or replace the battery:
- Locate the battery compartment lid (11) on the caliper.
- Use the provided mini screw or a suitable tool to gently rotate the battery cover counter-clockwise to open it.
- Insert the 3V CR2032 battery with the positive (+) side facing up.
- Close the battery cover by rotating it clockwise until it is securely locked.
4. Инструкция по эксплуатации
4.1 Основные операции
- Power ON/OFF (13): Press the "ON/OFF" button to turn the caliper on or off. The caliper also features automatic power-off after 5 minutes of inactivity.
- Unit Conversion (4): Press the "in/mm" button to switch between millimeter (mm) and inch (in) measurement systems. When in inch system, the LCD will display "in".
- Zero Setting (12): The "ZERO" key allows you to set the display to zero at any position within the measuring range. This is useful for relative measurements.
4.2 Подготовка к измерению
- Before use, loosen the fastening screw (5) on the caliper frame.
- Gently pull the caliper frame open.
- Use a clean, soft cloth to wipe the measuring surfaces and the guiding surface clean.
- Check Zero Position: Gently push the caliper frame until the two measuring jaw surfaces are completely closed. The LCD readout should display "zero". If it does not, press the "ZERO" key to set it to zero.
4.3 Методы измерения
The caliper supports four-way measurement: outside diameter, inside diameter, depth, and step measurement.
- Outside Diameter Measurement: Fix the outside measuring faces (1) close to the workpiece to be measured.
- Inside Diameter Measurement: Place the inside measuring jaws (3) into the object and expand them to measure the internal diameter. Ensure the jaws are in the diameter direction and not leaning.
- Измерение глубины: Place the depth measuring blade (9) vertically with the workpiece's bottom surface.
- Измерение шага: Use the step measuring faces (2) to measure the height difference between two surfaces.
Direct Measurement: Use the caliper to measure the workpiece directly. The LCD readout will display the measured value directly.
Относительное измерение: Set "zero" when measuring a standard workpiece or sample. Then, measure the new workpiece; the LCD will display the relative measuring value compared to the standard.
4.4 Вывод данных
The caliper features a data output interface (7). Data can be outputted to a printer or computer for processing and printing, but requires a separate SHAHE Data Output Device (sold separately).
Video 1: Demonstration of SHAHE Digital Caliper in use, showing various measurements and unit conversion.
5. Техническое обслуживание
- Avoid exposing the caliper to areas with high dust, direct sunlight, ultraviolet radiation, or high temperatures.
- Handle the caliper gently; do not drop or crash it.
- Clean the measuring surface with gasoline or alcohol, ensuring no liquid comes into contact with electronic components or the upper surface of the measuring blade.
- The recommended usage and test environmental relative humidity is ≤80%.
6. Поиск Неисправностей
| Общая неисправность | Возможная причина | Поиск неисправностей |
|---|---|---|
| Readouts jump or no readouts | Poor battery contacts or dead battery | 1. Check the inner battery contact. 2. Замените аккумулятор. |
| Readouts display irregularly | Caliper under damp and moisture situation | Clean the measuring blade upper surface with gauze or open it and clean. |
7. Технические характеристики
| Особенность | Описание |
|---|---|
| Название бренда | Шахе |
| Номер модели | 5110-150 (also available in 5110-200, 5110-300) |
| Товары для самостоятельного изготовления | Металлообработка |
| Материал | Закаленная нержавеющая сталь |
| Диапазон измерения | 0-150 mm / 0-6 inch (depending on model) |
| Разрешение | 0.01 мм / 0.0005 дюйма |
| Точность | ±0.02 mm (for 0-150 mm model) |
| Caliper Type | Цифровые штангенциркули |
| Защита | Водонепроницаемость IP54 |
| Емкостный сетчатый преобразователь | Стеклянная фиксированная сетка |
| Функции измерения | Four-way (Outside Diameter, Inside Diameter, Step, Depth) |
| Вывод данных | Yes (requires separate SHAHE Data Output Device) |
| Тип батареи | 3V CR2032 Environmental Lithium Battery |
| Срок службы батареи | >1 year (under normal use) |
| Автоматическое отключение питания | После 5 минут бездействия |
| Скорость отклика | 3 метра/секунду |
| Рабочая среда | Temperature 0-40℃, Relative Humidity ≤80% |
8. Советы пользователю
- Срок службы батареи: The CR2032 battery can last for a year or more, even with frequent use, making it a reliable tool for extended periods.
- Прочность: The hardened stainless steel construction is robust and resistant to scratches, maintaining accuracy over time.
- Быстрый старт: The caliper often powers on automatically when the slider is moved, allowing for immediate use without pressing the ON/OFF button.
9. Гарантия и поддержка
This SHAHE Digital Vernier Caliper comes with a one-year warranty from the date of purchase.
For detailed information, additional instructions, or support, please refer to the official user manual PDF available at: SHAHE Digital Caliper User Manual (PDF).
