INSTALLATION AND APPLICATION INSTRUCTIONS –
CONFIGURATION
- COVER TAPA COUVERCLE
- RSL-LMS
RSL-LMB
RSL-LMM
RSL-LM-RGB - RSL-SM
RSL-SMM - RSL-WML
RSL-WMLM
RSL-WMH
RSL-WMHM - RSL BASE FLAT
- RSL BASE WALL
- RSL BASE EXTENDED
- RSL BASE POLE
- RSL BASE TUBE
- GASKET
JUNTA
JOINT - GASKET
JUNTA
JOINT
DIMENSIONS
INSTALLATION
For installation of the item according to Type 4X, use PA 6.6 washers and AISI 304 steel screws.
ELECTRICAL WIRING
Wiring diagram
ENSURE THAT THE POWER SUPPLY VOLTAGE OF THE MODULE IS THE SAME AS THAT OF THE NETWORK!
– INSTALLATION MUST BE MADE BY TRAINED PERSONNEL.
ON THE POWER SUPPLY LINE USE APPROPRIATE TIME-LAG FUSES ACCORDING TO THE VOLTAGE.
– IT IS POSSIBLE TO CONNECT TOGETHER UP TO MAX 5 WIRING BASES
The recommended section of the power supply cable is 0,5 mm
AWG range: 14 – 30 SOL and STR or equivalent
For devices rated 12-24 Vac/Vdc only: Power supply shall be connected to a “Class 2” or “Limited Voltage Limited Current (LVLC)” source only
RSL-WML – 24V ACDC
*Not available for the RSL-LM-RGB version
RSL-WMLM – 24V ACDC 
BL: Flashing Light – Only for RSL-LMS, RSL-LMB and RSL-LM- RGB set to Steady-ON
N/C: Continuous light – Acoustic module
*Not available for the RSL-LM-RGB version
RSL-WMH – 120/240V AC
The recommended section of the power supply cable is 0,5 mm 
RSL-WMHM – 120/240V AC 
BL: Flashing Light – Only for RSL-LMS, RSL-LMB and RSL-LM- RGB set to Steady-ON
C: Continuous light – Acoustic module
RSL-LM-RGB
ATTENTION: The RSL-LM-RGB module occupies 3 of the 7 channels on the terminal of the RSL base
| Red | Green | Blue | Violet | Yellow | Cyan | White | |
| CH1 | X | X | X | X | |||
| CH2 | X | X | X | X | |||
| CH3 | X | X | X | X |
ATTENTION: RSL-LM-RGB with RSL-WML and RSL-WMLM works only in NPN mode
INDICATIONS TO CHANGE THE FLASHING MODE
DISCONNECTED POWER SUPPLY BEFORE MAKING ANY INTERVENTION ON THE DEVICE 
 |
 |
 |
 |
|
| OFF-OFF | ON-OFF | OFF-ON | ON-ON | |
| RSL-WMLM | 1 FLASH | 2 FLASH | 3 FLASH | 5 FLASH |
| RSL-WMHM | 1 FLASH | 2 FLASH | 3 FLASH | 5 FLASH |
| RSL-LMM | 2 FLASH | 3 FLASH | 5 FLASH | RANDOM |
| RSL-LM-RGB | STEADY | 1 FLASH | 3FLASH | RANDOM |
CURRENT CONSUMPTION
RSL-LMS
24V |
24V |
120V |
240V |
|
| RSL-WM* (mA) | 35 | 75 | 30 | 25 |
| RSL-WM*M (mA) | 50 | 110 | 30 | 25 |
RSL-LMB
| 24V |
24V |
120V |
240V |
|
| RSL-WM* (mA) | 50 | 60 | 35 | 25 |
| RSL-WM*M (mA) | 70 | 100 | 35 | 25 |
RSL-LMM
| 24V |
24V |
120V |
240V |
|
| RSL-WM* (mA) | 60 | 100 | 35 | 25 |
RSL-LM-RGB
| 24V |
24V |
120V |
240V |
|
| RSL-WM* (mA) | 220 | 400 | 90 | 50 |
* indicates voltage: (L) 12.24VAC/DC, (H) 120-240VAC
ATTENTION
| ATTENTION | To facilitate assembly, use only silicone lubricants |
| ATTENTION | The possibility exists that rapid flashing lights, under certain circumstances, might induce photosensitive epilepsy |
NOT TO BE DISPOSED OF AS COMMON WASTE
2645 Federal Signal Drive University
Park, IL 60484 United States
Phone: 708-534-4756
Fax: 708-534-4852
www.fedsig.com
signalsupport@fedsig.com
Ref. 25500318 REV A4
Documents / Resources
 |
RSL RSL Series Radiant Stack Light [pdf] Installation Guide RSL-WML, RSL-WMLM, RSL-WMH, RSL-WMHM, RSL Series Radiant Stack Light, RSL Series, Radiant Stack Light, Stack Light, Light |