RS-PRO-logo

RS PRO RSFG-1013 Function Generator

RS-PRO-RSFG-1013-Function-Generator

Limited Warranty

This product is warranted to the original purchaser against defects in material and workmanship for 3 years from the date of purchase. During this warranty period, RS PRO will, at its option, replace or repair the defective unit, subject to verification of the defect or malfunction. This warranty does not cover fuses, disposable batteries, or damage from abuse, neglect, accident, unauthorized repair, alteration, contamination, or abnormal conditions of operation or handling. Any implied warranties arising out of the sale of this product, including but not limited to implied warranties of merchantability and fitness for a particular purpose, are limited to the above. RS PRO shall not be liable for loss of use of the instrument or other incidental or consequential damages, expenses, or economic loss, or for any claim or claims for such damage, expense or economic loss. Some states or countries laws vary, so the above limitations or exclusions may not apply to you. For full terms and conditions, refer to the RS PRO website.

This quick start guide contains proprietary information, which is protected by copyright. All rights are reserved. No part of this quick start guide may be photocopied, reproduced or translated to another language without prior written consent.

The information in this quick start guide was correct at the time of printing. However we continue to improve our products and therefore reserve the right to change the specifications, equipment, and maintenance procedures at any time without notice.

SAFETY INSTRUCTIONS

Safety Symbols
These safety symbols may appear in the user manual or on the instrument.

RS-PRO-RSFG-1013-Function-Generator-1

Main Features

Performance •   High resolution using DDS technology

•   High frequency accuracy: ±20ppm

•   Low distortion: −55dBc @ ≤200kHz

•   High resolution 100mHz

Features •   Digital user interface with 6-digit LED display

•   Various output waveforms: Sine, Square, and Triangle

•   TTL output

•   Amplitude control

•   −40dB attenuation

•   Duty control

•   Variable DC offset control

•   Output On/Off control

•   Voltage display

•   Output overload protection

Interface •   Frequency output

•   TTL output

Appearance

Front Panel Overview

RS-PRO-RSFG-1013-Function-Generator-2

Description
1. Main Display 2. Entry Keys
3. Shift Key 4. Output On/OFF key
5. Main Output 6. TTL Output
7. Amplitude Control 8. Offset Control
9. Duty Control 10. Frequency Adjustment Knob
11. Power Switch  

Rear Panel Overview

RS-PRO-RSFG-1013-Function-Generator-3

Description
1. Ground Terminal 2. AC Power Input
3. AC rating information  

START UP

Power Up

Step 1. Connect the power cord to the AC voltage input. Check the voltage level displayed on the label (1) and make sure it is identical to the AC line. Then connect the power cord (2).

RS-PRO-RSFG-1013-Function-Generator-4

  2. Push and turn on the main power switch on the front panel.

RS-PRO-RSFG-1013-Function-Generator-5

  3. The display shows the default setup: Sine wave, 1kHz

RS-PRO-RSFG-1013-Function-Generator-6

Functionality check

Step 1. Connect SFG main output to measurement device such as oscilloscope.

RS-PRO-RSFG-1013-Function-Generator-7

  2. Press the output key. The output is activated and the LED turns on.

RS-PRO-RSFG-1013-Function-Generator-8

  3. Observe the output waveform: 1kHz, sine wave.

Operation Shortcuts

Sine Wave

RS-PRO-RSFG-1013-Function-Generator-9

Triangle wave

RS-PRO-RSFG-1013-Function-Generator-10

Square Wave

RS-PRO-RSFG-1013-Function-Generator-11

TTL Output

RS-PRO-RSFG-1013-Function-Generator-12

Activate waveform

RS-PRO-RSFG-1013-Function-Generator-13

2. Press the output key. The LED turns On.
3. The waveform comes out from the main terminal.
10Vp-p (50Ω load)
20Vp-p (no load)

RS-PRO-RSFG-1013-Function-Generator-14

Set Frequency

RS-PRO-RSFG-1013-Function-Generator-15

RS-PRO-RSFG-1013-Function-Generator-16

Set Duty Cycle

RS-PRO-RSFG-1013-Function-Generator-17

SPECIFICATIONS

RSFG-1013 must be powered for at least 30 minutes within the ambient temperature 18˚C ~ 28˚C to meet this spec.
Main

Output Function Sine, Square, Triangle
Amplitude Range 10Vpp (50Ω load)
Amplitude Accuracy ±20% at maximum position
Impedance 50Ω ± 10%
Attenuator −40dB ± 1dB x1
DC Offset < −5V ~ >+5V (50Ω load)
Duty Range 25% ~ 75%, ≤1MHz (Square Wave)
Display 6 digits LED display

Frequency 

Sine/Square Waveform Range 0.1Hz ~ 3MHz
Triangle Waveform Range 0.1Hz ~ 1MHz
Resolution 0.1Hz maximum
Stability ±20ppm
Accuracy ±20ppm
Aging ±5ppm/year
Sine/Square Waveform Range 0.1Hz ~ 3MHz
Triangle Waveform Range 0.1Hz ~ 1MHz

Sine Wave 

Harmonic Distortion ≥ -55dBc, 0.1Hz ~ 200kHz

≥ -40dBc, 0.2MHz ~ 2MHz

≥ -35dBc, 2MHz ~ 3MHz

(At maximum position without any attenuation to 1/10 of any combination setting, TTL Off)

Flatness < ± 0.3dB, 0.1Hz ~ 1MHz

< ± 0.5dB, 1MHz ~ 2MHz

< ± 1dB, 2MHz ~ 3MHz

(At the max amplitude relating to 1kHz)

Triangle Wave 

Linearity ≥ 98%, 0.1Hz ~ 100kHz

≥ 95%, 100kHz ~ 1MHz

Square Wave 

Symmetry ±5% of period + 4ns, 0.1Hz ~ 100kHz
Rise/ Fall Time ≤ 100ns at maximum output, 50Ω load

TTL 

Level ≥ 3Vpp
Fan Out 20 TTL Load
Rise/ Fall Time ≤ 25ns

General 

Power Source AC110/220/240V ±10%, 50/ 60Hz (Line voltage setting is factory installed)
 

Operation Environment

Indoor Use, Altitude Up to 2000m Ambient Temperature 0 ~ 40°C Relative Humidity ≤ 80%, 0 ~ 40°C

Install Category II / Pollution Degree 2

Storage Environment Temperature -10 ~ 70°C Humidity ≤ 70%
Accessories Instruction Manual x 1 GTL-101 x 1
Dimension 251 (W) x 91 (H) x 291 (D)
Weight Approx. 2.1kg

Africa
RS Components SA
P.O. Box 12182, Vorna Valley 1686
20 Indianapolis Street, Kyalami Business Park
Kyalami, Midrand, South Africa

Asia
RS Components Ltd.
Suite 1601, Level 16, Tower 1, Kowloon Commerce Centre, 51 Kwai Cheong Road, Kwai Chung, Hong Kong

China
RS Components Ltd.
Suite 23 A-C, East Sea Business Centre Phase 2
NO. 618 Yan’an Eastern Road, Shanghai, 200001, China

Europe
RS Components Ltd.
PO Box 99, Corby, Northants NN17 9RS
United Kingdom

Japan
RS Components Ltd.
West Tower (12th Floor), Yokohama Business Park,
134 Godocho, Hodogaya, Yokohama,
Kanagawa 240-0005 Japan

North America
Allied Electronics
7151 Jack Newell Blvd. S. Fort Worth, Texas 76118
U.S.A.

South America
RS Componentes Electrónicos Limitada
Av. Pdte. Eduardo Frei M. 6001-71, Centro Empresas El Cortijo Conchali, Santiago, Chile

RS-PRO-RSFG-1013-Function-Generator-18

Documents / Resources

RS PRO RSFG-1013 Function Generator [pdf] User Guide
RSFG-1013, 2889873, RSFG-1013 Function Generator, RSFG-1013, Function Generator, Generator

References

Leave a comment

Your email address will not be published. Required fields are marked *