Royalcraft Kingston 6 Seat Set with Lazy Susan-Table Instructions

Kingston 6 Seat Set with Lazy Susan-Table
Assembly Instructions
Product size: D150.5*H73.5 cm
All diagrams are for assembly reference only.

This product is for Domestic use only!
IMPORTANT, RETAIN FOR FUTURE REFERENCE READ CAREFULLY

Contents hide

1 Before you start

2 Parts List

3 Documents / Resources

3.1 References

4 Related Posts

Before you start

Warnings
IMPORTANT, RETAIN FOR FUTURE REFERENCE READ CAREFULLY

See enclosed instructions for assembly, safety, and care information. Failure to follow the warnings could result in serious injury. Handle heavy parts with care. Ensure that this product is fully assembled as illustrated before use. This product should only be used on firm, level ground. Keep small parts out of reach of children. Do not stand or climb onto this product. This product is intended for domestic use only.
Furniture can be dangerous if incorrectly used. No liability will be accepted for damage or injury caused by the incorrect use of this product.

Dos
When you are ready to start, make sure that you have the right tools, plenty of space, and a clean, dry area for assembly. Removing all packaging and banding and place the components carefully on suitable surfaces to prevent damaging or scratching them. Check the pack and make sure you have all of the parts listed. Check all screws and bolts are tightened and inspect regularly. This product is suitable for all-year outdoor use. However to prolong its life we recommend that during severely bad weather and during the winter months, it is stored in a cool, dry place. Before storage, ensure that the product is clean and dry. To clean, wipe down with a sponge and warm soapy water and wipe with a clean, dry cloth. sponge and warm soapy water and wipe with a clean, dry cloth.

Don’ts
Do not use scourers, abrasives, washing powders, chemical cleaners or any other substances containing abrasives since these substances can damage the product.Do not use power tools to construct this product. Do not use this product if parts are missing, damaged or worn. Do not sit or lean on this product. Do not stand or climb onto the product and do not use it as a ladder, as this could lead to it unbalancing and overturning. Never drag furniture when moving it, always lift it.
Number of people required for assembly

Two people

Time to assemble

30 Minutes

Tools required

Tips: Do NOT fully tighten bolts/nuts before all components are connected. Only fully tighten once you are satisfied with the alignment of all components. Do not over-tighten the bolts.

Components, fixtures & fittings (not actual size)

Parts List

Part No.	Diagram	Qty.	Part No.	Diagram	Qty.
A	Table Top	1 PC	B	Table Leg	4 PCS
C	Connecting Panel	4 PCS	D	Bolt	4 PCS
F3	Flat Washer	12 PCS	F4	Spring Washer	12 PCS
G	Nut	12 PCS	F2	Bolt/Nut Cap	12 PCS
S1	Spanner	1 PC

Step by step assembly instructions
All Bolt Head/Nut Caps should not be attached before finally tightening all Bolts/Nuts with Spanner.

Step One
With the help of another person, open the packaging and place the Table Top (A) upside down on a flat, non-abrasive surface to avoid scratching the table surface or rim.

Step Two
Screw the Bolts (D) into the holes, tighten them using Screw Driver (not provided).

Step Three
Loosely attach the Table Legs (B) to the Table Top (A) using Nut Caps (F2), Nuts (G), Spring Washers (F4) and Flat Washers (F3).

Step Four
Loosely attach the Connecting Panels (C) to the Legs (B) using Nut Caps (F2), Nuts (G), Spring Washers (F4) and Flat Washers (F3).

Step Five
Once you are satisfied with the alignment of the components carefully tighten all Bolts/Nuts using Spanner (S1). Do not over-tighten. Cover each Bolt/Nut with Cap (F2). With the help of another person, carefully turn the table in the upright position. Level the table by adjustable feet screws. Your table is now ready for use.