ROXX CLUSTER B4 FC LED Lights User Manual

Ensure stable and compatible stands or brackets are used for installation.
Consider using the optional ROXX YOKE FLOOR EXTENSION for standing installations.

Connections

Connect the device as follows:

AC Power: Use the provided power cord with a plug suitable for EU countries.

DMX Connection: Follow the cable connection instructions provided.

Startup

To start the CLUSTER B4 FC:

Ensure proper power and DMX connections are established.
Power on the device using the designated power switch.

Control Display

The control display provides information on the current settings and configurations.

Troubleshooting

If you encounter any issues with the CLUSTER B4 FC, refer to thetroubleshooting section in the user manual for guidance.

Frequently Asked Questions

Q: Can the CLUSTER B4 FC be used outdoors?
A: The device is not recommended for use in tropical climates or outdoor environments due to potential operational issues.

View Fullscreen

SAFETY INFORMATION

1.1. General Preventive Measures 1.1.1. Please read, understand and follow the instructions. 1.1.2. Store the instructions and information in a safe place.
Best solution is the ring binder provided by ROXX. 1.1.3. Follow all safety warnings. Under no circumstances remove safety warnings
or other information from the equipment. 1.1.4. Don’t use the equipment for any other intended purpose or manner. 1.1.5. Use only stable and compatible stands and/or brackets. Especially when fix installed.
Make sure the wall brackets are properly installed and safe. Make sure the device is securely installed and cannot fall. 1.1.6. Check the safety regulations applying for your country before and during installation. 1.1.7. Keep the device away from heat! Don’t place/install near heaters, ovens or any source of heat. Make sure that the device always is efficiently cooled and cannot overheat. 1.1.8. Always guarantee that ventilation and cooling slots are clean and not blocked. 1.1.9. Item must be away minimum 20cm from anything around and above it. 1.1.10. Do not use this device close to water. 1.1.11. Do not expose this equipment to flammable materials. 1.1.12. Make sure that no objects can fall into the device. 1.1.13. Only use this device with the accessories recommended by the manufacturer. 1.1.14. Always check the equipment for housing damages, so that no water can enter the device. No containers containing liquids of any kind should be place on top of the unit. 1.1.15. Opening or modifying this device is only allowed by authorized and qualified persons. 1.1.16. All cables need to be checked after connecting the device in order to prevent damage or accidents. 1.1.17. Make sure that the device is transported safe and packed proper in order to prevent damage of any kind. 1.1.18. Once you notice improper function of your device due to damage, electric shock or anything similar, immediately unplug the unit from the mains outlet and contact our service department. 1.1.19. Clean the device with a dry cloth.
4

User Manual
1.1.20. Observe all disposal laws applicable in your country. Especially for the packaging. 1.1.21. Plastic bags are not a toy! Keep away from children! 1.1.22. Please note that changes or modifications which are not approved by the party responsible
for compliance will void the user’s authority to operate the device.
1.2 Regulations for equipment that connects to power mains 1.2.1. If an earthing contact is available in the used power cord, it must used in combination
with an power outlet, providing a protective ground. In no circustances should the protective ground be deactivated. 1.2.2. Do not switch on the device immediately after it has been in strong different temperatures, especially after transport. Let the device acclimatize to the temparature in the room of usage first to prevent moisture and condensation. 1.2.3. Verify that the correct voltage and frequency are available in the area of operation, before connecting the unit to the mains outlet. 1.2.4. If the plug doesn`t fit in your mains outlet, contact your electrician. 1.2.5. Make sure your power cord/adapter/connector does not show signs of kinks/warps or is being stepped on. 1.2.6. Allwas disconnect the unit when not in use or being cleaned. Don`t pull on the cord to disconnect. Only touch power connections with dry hands! 1.2.7. Don`t switch the unit on/off rapidly. This may cause damage. 1.2.8. If a fuse needs to be replaced, ALWAYS make sure that exact the same fuse will be used (type and rating). Repeatedly blown fuses need to be checked by an authorised service technician. 1.2.9. In the risk of lighting strike all units need to be unpluged from the mains in order to prevent damage. 1.2.10. During installation there must be a voltage free condition. 1.2.11. The device needs to be cleaned and serviced regularly and will credit this with a longer life cycle. Dust, dirt, moist, water, smoke, nicotine or anything similar inside the unit will cause damage/malfunction. 1.2.12. The unit needs to have at least 0,5m distance to anything flammable. 1.2.13. You have to make sure that any electrical installation applys to the laws of your country. Correct power cables and applying standards have to be used.

User Manual
1.3. Technical warnsigns and explanation In order to prevent the risk of an electric shock, under no circumstances remove the cover/back or open the unit in any way! No user serviceable parts are inside. Service, maintenance and repairs should only be done by qualified service personnel or the manufacturer. Dangerous uninsulated voltage inside the device can cause an electrical shock when opened by unqualified personnel.
Important operating and maintenance instructions apply!
Do not operate this device in tropical climates.
CAUTION! Intense LED light source! Risk of eye damage. Do not look into the light source The housing surface of the spotlight can heat up to temperatures as high as 70 °C in regular use. Ensure that it is not possible to come into contact with the housing unintentionally. Always allow sufficient time for the lamp to cool down before dismantling, carrying out maintenance work or charging etc..
IMPORTANT IMFORMATION! · This is a product which has been developed for professional usage
in event technology. It is not suitable as a houshold lighting. · NEVER stare, not even temporarily, directly into the light source. · Don`t use magnifiers or any other optical instrument to look at the beam. · The effects of this device, expecially the stroboscope effect, can cause
problems for sensitive people or may even cause epileptical seizures.
6

User Manual
2. INTRODUCTION

2.1. About us
The name ROXX® came easily. Combined with the concentrated knowledge and many years of experience, our three founders, who have been leaving their mark in the event and lighting industry for many years already, came together in 2020 to start this outstanding venture. Product development, sales and marketing as well as the exceptional know-how and the profound rooting in the field of the professional lighting technology belong to our core competences and therefore guarantee extremely innovative and reliable products, excellent support and professional service in every aspect.
Designed & developed in Germany ROXX® products are developed and designed in Germany. Always in tight consultation with our customers and experts who will eventually be working with these tools. This ensures innovative, easy-to-use and performanceoriented solutions, which provide added value for our customers.
Made to last Recommended for permanent outdoor use, most ROXX® products feature additional corrosion protection and enhanced IP66 equipment protection, thereby providing that crucial extra for a wider range of applications. In addition to architectural or theme park applications, even fixed installations in coastal or offshore areas with high salt exposure can be reliably implemented over long periods of time.

2.2. CLUSTER B4 FC
All CLUSTER products can be easily connected both horizontal and vertically, by using the integrated C-Lok system. The series is made to enable toolless multiple array confi gurations, scalable from a single vertical line, to massive matrix like arrays. Due IP65 rating all products are outdoor ready and protected from ingress of dust and rain. There are several mounting options Camlock mounts on top and back enable the use of Omega-Brackets, Yokes can be attached to mounting points on all sides, or the internal C-Lok system can be used for seemless interconnection. Pre-Link Magnets on top and side help to allign the fi xtures, giving an incredible user-friendly operation and save interlocking. A specially designed rigging bracket is used for seemless connection of multiple Blinders, to avoid gaps due to bracing of the truss structure by variable, sliding mounting positions. Floor extensions can be used to create vertical structures in single or double rows. The Full Color version reproduces the same look by using it´s warmwhite LED´s in combination with RGB and Amber, plus the full range of user adjustable color mixing and tunable white.
7

User Manual
3. GENERAL PRODUCT INFORMATION
3.1. Scope of delivery 1x CLUSTER B4 FC Power cord with plug (EU country specific, if not ordered differently) Pre-installed PUK
We´re offering a wide range of professional accessories (optional). Please see under menu 6 or at our website www.roxxlight.com 3.2. Control Functions · 1CH DWE, 2CH DWE, 4-1CH DWE, 4-2CH DWE, 9CH DWE+, 8CH STROBE, 12CH RGB, 10CH BASIC RGB,
14CH BASIC RGB, 21CH SECTION RGB, 21CH STANDARD RGB (default), 22CH Comp RGB, 38CH STANDARD RGB, 40CH EXTENDED RGB, 57CH EXTENDED RGB, 20CH DIRECT, 12CH DIRECT, 29CH DIRECT, 48CH DIRECT, 73CH DIRECT · RDM (Remote Device Management) · Stand Alone Functions including auto programs, LEE adjusted color macros, custom color templates and Tunable White · Master & Slave 3.3. Features
8

User Manual
4. INSTALLATION & SETUP
4.1 Physical Installation and Rigging ROXX CLUSTER B4 FC may be installed in any orientation. For this purpose the product provides several options:
Standing: The fixtures Yoke includes two M8 inner threads to install the optional ROXX YOKE FLOOR EXTENSION.

Hanging: The fixture can be installed in different ways:
1. Directly by integrated 1/4 turn Camlocks on top- or rear side

Open Closed

Omega Bracket ST

User Manual

2. By included yoke with several mounting points: B

Multiple mounting points: A: 3x Camlock with ¼ turn adapters B: 3x M12 / ½” C: 1x TV Spigot

C
A
Additional Yoke anchor points: In the delivery state, the yoke is preinstalled in such a way that the individual eyes can be rotated +/-20° in the pan. Each CLUSTER device also provides side anchor points for the yoke so that the device can then be rotated either clockwise or counterclockwise so that the individual eyes can then be adjusted +/-20° in tilt movement.
In addition, the B4 W and B4 FC models offer a third, lower anchor point that can be used to mount the optional YOKE 4.3 to optimize the center of gravity on, for example, a 6-lite or 8-lite.
Attention! This should only be used when clustering several units together, as otherwise the center of gravity of the individual unit is no longer in the middle and the unit can unintentionally tip over when the yoke is released.

User Manual

3. Using optional ROXX RIGGING BRACKET
For seemless connection of multiple Blinders, to avoid gaps due to bracing of the truss structure by variable, sliding mounting positions.
Product Clustering All CLUSTER products can be easily connected both horizontal and vertically, by using the integrated C-Lok system. The series is made to enable toolless multiple array configurations, scalable from a single vertical line, to massive matrix like arrays. To connect the devices with each other, proceed as follows in sequence:
1. Bring the devices together with the respective top and bottom side. A so-called centering puk is pre-installed on the top of every cluster device. This should always be installed when connecting the devices to each other.
2. Pre-Link Magnets on top and side help to allign the fixtures due cluster process and giving support operation for convenient and save interlocking.
Important Note: Even though the pre-link magnet system is strong enough to hold the devices together, at least one hand must always remain on the device for support during the connection.
11

User Manual

3. Make sure that the C-Lok hooks are turned counterclockwise (CCW) to the end-position first before you finally lock the C-Loks.

4. For locking all C-Lok´s, please turn them clockwise into end-position.
Note: As soon as both dot indicators are in line, the C-Lok is securely locked
Maximum Tensile and Torsion Load Before setting up Cluster configurations, be aware of the maximum tensile and torsion load, listed here below. Also make sure the mounting clamps are capable of supporting the total weight of your configuration. The different rigging options of all Cluster products result in different maximum tensile and torsion loads that must not be exceeded for a safe overhead installation.
The maximum loads listed here below take into account the 10-fold safety! 1. Rigging by integrated 1/4 turn Camlocks on top- or rear side

Max. Tension Load: 90kg Max. Torsion Load: 14.500 Nmm

Max. Tension Load: 90kg Max. Torsion Load: 6.700 Nmm
12

User Manual
2. Rigging by Yoke with multiple mounting points

a. With 1x Mounting Clamp Max. Tension Load: 41kg Max. Torsion Load: 4.280 Nmm

b. With 2x Mounting Clamp Max. Tension Load: 90kg Max. Torsion Load: 9.096 Nmm

c. With 1x Omega Bracket Max. Tension Load: 49kg Max. Torsion Load: 5.041 Nmm

d. With 2x Omega Bracket Max. Tension Load: 90kg Max. Torsion Load: 10.808 Nmm

3. Using optional ROXX RIGGING BRACKET with 2x Mounting Clamps

Max. Tension Load: 72kg Max. Torsion Load: 6.326 Nmm
13

User Manual
Important Note: Please be aware of using the centering PUK for safe RIGGING BRACKET installation to the CLUSTER device.

4.2 Connections*

A: Mains In: IP65 Power input connector with rubber sealing cap.Connect using the provided power cable (when not in use, always close with rubber sealing cap).

B: Mains Out: IP65 Power output connector with rubber sealing

D cap. Provides power to additional fixtures. Ensure that the to-

tal power consumption of all daisy-chained devices connec-

B ted do not exceed 8A (Ampere)! (when not in use, always close

with rubber sealing cap).

C: DMX IN: Male IP65 5-pin XLR connector (when not in use,

E always close with rubber sealing cap).

F D: DMX OUT: Female IP65 5-pin XLR connector

when not in use, always close with rubber sealing cap).

E: GoreTex

F: Safety Eyelet

G: IP65 USB port for firmware updates

*Note: In order to provide protection from spraying water, in accordance with protection class IP65, special IP65rated XLR connectors must be used correctly with the DMX input and output sockets, or they must be closed using the rubber sealing caps. When connected correctly, or when sealed correctly with the rubber sealing caps, the POWER IN and POWER OUT sockets are protected from spraying water, as in accordance with IP65.

User Manual

4.2.1. AC Power The CLUSTER B4 FC operates on any 100260 V, 50/60 Hz AC mains power supply with a maximum power consumption of 220W. Connect the fixture to AC power using the supplied cable or a similar one with Neutrik powerCON TRUE1 NAC3FX-W or a compatible type, to ensure the correct ingress protection (IP). For temporary installations, the mains cable must be fitted with a grounded connector intended for exterior use. The fixture must be grounded/earthed and be able to be isolated from AC power. The AC power supply must incorporate a fuse or circuit breaker for fault protection.

Wire Color (EU models) Brown Blue Yellow / Green

Wire Color (US models) Black White Green

Conductor Live Neutral Ground (earth)

Symbol L N
or

Warning! Read “Safety Informations” starting on page 3 before connecting the fixtures to AC mains power! Do not connect the fixture to an electrical dimmer system, as doing so may cause damage that is not covered by the product warranty!

4.2.2. DMX Connection The CLUSTER B4 FC is fully controllable by DMX (USITT DMX512-A standard, based on RS-485) and RDM.

4.2.2.1. Cable Connection If using a cabled DMX system, connect the DMX IN cable to the input connector (male 5-pin XLR connector) and DMX OUT cable to the output (female 5-pin XLR connectors).

For outdoor installations, use only IP65-rated XLR connectors. Use shielded twisted pair cable designed for RS-485 devices. The cables are daisy chained between the fixtures, and up to 32 fixtures can be connected to the same DMX link. Up to 300 meters (1000ft.) of cable is achievable with high quality DMX cables. All DMX links must be terminated in the last fixture by connecting a DMX termination plug to the last fixture’s 5 pin DMX out connector.

Standard microphone cable is not suitable for transmitting DMX.

DMX Termination on last fixture DMX out

XLR pin out

DATA GND

2 34

DATA –

DATA +

120 Ohm +/- 5%

DATA GND

2 34

DATA –

DATA +

User Manual
5. OPERATION
5.1 Start up* Once the fixture is connected to AC power, the boot process starts and the following information will appear on the display: “Ready to ROXX”, the product name and the current software version.
After this process, the fixture is ready for operation, and starts in the previously enabled mode.
*Note: During boot process the fan spins up quickly to blow out some possible dust from last use.
5.2 Control Display* OLED Display with Touch-Sensitive controls
ENTER Press ENTER to access the selection menu for system settings or confirm changes.
ESC Press ESC to take a step back in the menu.
Press arrows to scroll up and down inside the menu and change values, such as DMX address.
*Note: For a smooth navigation thru the menu settings, please make sure the display surface is dry and dust free.
After approximately 1 minute of inactivity inside the menu settings, the display will automatically jump back to home screen.
5.3 Display Short Cuts*
Short Cuts For some always recurring functions the fixture allows quick and user-friendly access at home screen over some display control short-cuts:
User Reset or Factory Reset*
ENTER + ESC
Pressing ESC+ENTER simultaneously a Factory Reset or User Reset can be started. By using the up/down arrows the Factory- or User Reset can be selected. For confirming press ENTER, to jump back please press ESC.
*Note: After Factory Reset all fixture settings are set back to factory default values. After User Reset all user selected reset functions and user default values will set back. Also a short self-test will start immediately while dimming in and out each single color.
16

User Manual

Display Off
ESC +
Pressing ESC + arrow down simultaneously the display backlight function will set to off and the display will turn off immediately. Once a control is pressed the display backlight will turn on.
Manual display flip function*
+
The fixture includes an auto display flip function by default. To use the manual display flip function please disable the auto flip function under Settings / Display first. Once the auto display flip function is disabled you can use the manual display flip function by pressing arrow up + arrow down simultaneously. The display will rotate 180. By pressing both arrows simultaneously again the display will flip back.
*Note: Once the display is flipped both Up / Down controls will work according to the display rotation.
5.4 Configuration
Home Screen After boot process the fixture is ready for operation and starts in the previously enabled mode. At home screen the following information will appear, depending on the current operating mode:
A DMX Adress B Operating Mode (DMX Mode, Quick Light or Standalone Mode) C Next available DMX address depending on the fixtures DMX footprint D External Data protocol (DMX). E The dot indicates the active protocol
A D

B
9 CH RGB

1
Next ( 10 )
C

·DMX
E

User Manual

5.4.1 Set DMX Start Address (Direct Access)
At Home Screen the DMX address can be changed directly by using the up and down arrows. During this process the DMX address starts blinking, once it´s confirmed by pressing ENTER it stops blinking. If the DMX address will not be confirmed by ENTER within 10 seconds, the display will jump back and show the DMX address from before and stops blinking.

5.4.2 Selecting DMX Mode*

At home screen please press ENTER to access to the main menu (level 1). While using UP / DOWN arrows, please select the menu item “DMX Mode” and confirm by pressing ENTER. In the following sub-menu (level 2), you can now choose between 18 different DMX operating modes while using the UP/Down arrows and confirm by pressing ENTER or jump back by pressing ESC. After confirmation the display will jump back to main menu (level 1). Press ESC for homescreen, here the selected DMX mode will be displayed.

*Note: For detailed information about the several DMX modes including channel assignment please see our DMX Control chart. .

Level 1

Level 2

DMX Mode

DMX Mode Stand Alone Slave Settings System Info

1CH DWE 2CH DWE 4-1CH DWE 4-2CH DWE 9CH DWE+ 8CH STROBE 12CH RGB 10CH BASIC RGB 14CH BASIC RGB 21CH SECTION RGB 21CH STANDARD RGB 38CH STANDARD RGB 40CH EXTENDED RGB 57CH EXTENDED RGB 20CH DIRECT 12CH DIRECT 29CH DIRECT 48CH DIRECT 73CH DIRECT

User Manual

5.4.3 Stand Alone*

Press ENTER to access to main menu (level 1). While using the UP / DOWN arrows, please select the menu item “Stand Alone” and confirm by pressing ENTER. In the following sub-menu (level 2), you can now choose between 5 different Stand Alone operating modes (Auto, Color Macro, Quick Color, Tunable White, User Color) ,Stop Stand Alone and Color Settings functions while using the UP/Down arrows and confirm by pressing ENTER or jump back by pressing ESC. To finally use Stand Alone programs please make sure DMX is disconnected to the fixture, as this protocol has priority.

Stop Stand Alone To stop a running Stand Alone mode immediately, please select “Stop Stand Alone” and confirm by pressing ENTER. The display will automatically jump back to level 1.

Level 1

Level 2

Stand Alone Mode

DMX Mode Stand Alone Slave Settings System Info

Stop Stand Alone Auto Color Macro Quick Color Tunable White User Color Color Settings Master

Auto*

Select “Auto” by using the up/down arrows and press ENTER. Here at sub-menu (level 3), you can choose between 10 different Auto Effects (Effect 1 – 10) and Stop Program. Using the Up/Down arrows you can select one of the 10 Effects and confirm by pressing ENTER or step back by ESC. After confirming your preferred Effect, you can now adjust speed and brightness at level 4.

To adjust speed, please use the UP / DOWN arrows to select the menu item “Speed”, and confirm with ENTER. After use UP / DOWN arrows to adjust the speed value between 000-100 and confirm by ENTER or jump back by ESC. To adjust brightness please select “Dim” as per the procedure previously described and confirm with ENTER. After use UP / DOWN arrows again to adjust the brightness value between 000-100 and confirm by ENTER or jump back by ESC.

Once it´s confirmed or denied the display will automatically jump back to level 3. To stop running a selected Effect please chose “Stop Program” at level 3 or “Stop Stand Alone” at level 2. For returning back to homescreen please press ESC three times. At homescreen the selected Stand Alone mode “Auto” and the selected program will be displayed.

*Note: Using arrows UP /DOWN at homescreen Auto programs can be directly changed according to the list.

User Manual
Level 1 Menu
DMX Mode Stand Alone Slave Settings System Info

Level 2
Stand Alone Mode
Stop Stand Alone Auto Color Macro Quick Color Tunable White User Color Color Settings Master

Level 3
Auto
Stop Program Effect 1 Effect 2 Effect 3 Effect 4 Effect 5 Effect 6 Effect 7 Effect 8 Effect 9 Effect 10

Level 4
Program
Speed <0-100> (Default 50)
Dim <0-100>

Auto
Effect 1

Color Macro* 46 different color macros (34x matched LEE color filters, 6 LED colors and 6 different Whites) are available as presets. For each the brightness can be adjusted separately.

Level 1
Menu
DMX Mode Stand Alone Slave Settings System Info

Level 2
Stand Alone Mode
Stop Stand Alone Auto Color Macro Quick Color Tunable White User Color Color Settings Master

Level 3
Color Macro
Color Off Color Macros Color Macro Chart Dim <0-100>

To select a color macro please press ENTER to access to main menu (level 1). While using the UP / DOWN arrows select the menu item “Stand Alone” and confirm by pressing ENTER. After please select the item “Color Macro” by using the up/down arrows and press ENTER again. Using UP and DOWN controls, select your desired color preset and confirm with ENTER. At level 3 you can adjust the brightness for the color preset between 000-100. Confirm by ENTER. For color blackout choose the item “Color Off”.
Note: Using UP / DOWN arrows at homescreen Color Macros can be changed according to the list.

User Manual

Level 4

Gels Color Macros for Standalone Mode

Pos. Gel Name

Color Number

1 Red

100% Red LED

2 Fire

LEE 019

3 Medium Red

LEE 027

4 Primary Red

LEE 106

5 Med Amber

LEE 020

6 Dark Amber

LEE 022

7 Deep Amber

LEE 104

8 Orange

LEE 105

9 Deep Golden Amber LEE 135

10 Yellow

LEE 101

11 Green

100% Green LED

12 Lime Green

LEE 088

13 Moss Green

LEE 089

14 LEE Green

LEE 121

15 Primary Green

LEE 139

16 Jas Green

LEE 738

Gels Color Macros for Standalone Mode

Pos. Gel Name

Color Number

17 jade

LEE 323

18 Blue

100% Blue LED

19 Sky Blue

LEE 068

20 Tokyo Blue

LEE 071

21 Light Blue

LEE 118

22 Marine Blue

LEE 131

23 Med Blue

LEE 132

24 Congo Blue

LEE 181

25 Mikkel Blue

LEE 716

26 Rose Pink

LEE 002

27 Med Pink

LEE 036

28 Light Lavender

LEE 052

29 Lavender

LEE 058

30 Magenta

LEE 113

31 Mauve

LEE 126

32 Smokey Pink

LEE 127

Gels Color Macros for Standalone Mode

Pos. Gel Name

Color Number

33 Special Med Lavender LEE 343

34 Ultimate Violet

LEE 707

35 Magical Magenta

LEE 795

36 Chrysalis Pink

LEE 798

37 Specia KH Lavender LEE 799

38 Bulb White

2700K

39 Halogen White

3200K

40 Neutral White

4200K

41 Daylight White

5600K

42 Cold White I

6000K

43 Cold White II

6300K

44 Amber (only if available) 100% Amber LED

45 Lime (only if available) 100% Lime LED

46 Cyan (only if available) 100% Cyan LED

Quick Color* The standalone mode “Quick Color” allows a direct adjustment of the single LED colors R, G, B, A, W, Dimmer and Shutter.

Level 1
Menu
DMX Mode Stand Alone Slave Settings System Info

Level 2
Stand Alone Mode
Stop Stand Alone Auto Color Macro Quick Color Tunable White User Color Color Settings Master

Level 3

Quick Color

Dimmer Shutter Red Green Blue Amber White

<0-100> <0-255> <0-255> <0-255> <0-255> <0-255> <0-255>

To adjust your Quick Color please press ENTER to access to main menu (level 1). While using the UP / DOWN arrows select the menu item “Stand Alone” and confirm by pressing ENTER. After please select the item “Quick Color” by using the up/down arrows and press ENTER again. Using UP and DOWN controls, select your desired color and confirm with ENTER. After you can adjust the brightness for the color between 000-255 and confirm by ENTER. Besides the individual color mix also a master dimmer can be adjusted between 000-100. For strobe effects please adjust the Shutter value between 000-255.
*Note: Please see detailed explanation for strobe effects inside DMX chart at the end of this manual. Using UP/DOWN arrows at homescreen you can change Quick Color´s dimmer value.
21

User Manual

Tunable White* The standalone mode “Tuneable White” allows the color temperature (CCT) to be adjusted from 2.000K 10.000K in 100K steps. Besides brightness and shutter also a +/- green and magenta correction is available.

Level 1
Menu
DMX Mode Stand Alone Slave Settings System Info

Level 2
Stand Alone Mode
Stop Stand Alone Auto Color Macro Quick Color Tunable White User Color Color Settings Master

Level 3

Tunable White

CCT TINT Dimmer Shutter

<2900> <000> (+/-127) <0-255> <0-255>

Starting from home screen press ENTER to access to main menu (level 1).

While using the UP / DOWN arrows select the menu item “Stand Alone” and confirm by pressing ENTER.

After please select the item “Tunable White” by using the up/down arrows and press ENTER again.

Using UP and DOWN controls to select your desired menu item, confirm by ENTER and adjust the desired value by up

and down controls and confirm all entries with ENTER.

*Note:

Tint values

000

= no function/neutral

001 – 127

= + green

-001 to – 127 = – green

*Note: Using UP/DOWN arrows at homescreen the selected CCT value can be changed in +/- 100K steps. Shutter: Please see detailed explanation for strobe effects inside DMX chart at the end of this manual.

User Color* The standalone mode “User Color” allows to store up to 5 customized color presets out of Red, Green, Blue, Amber, White, brightness and shutter.

Level 1
Menu
DMX Mode Stand Alone Slave Settings System Info

Level 2
Stand Alone Mode
Stop Stand Alone Auto Color Macro Quick Color Tunable White User Color Color Settings Master

Level 3
User Color
Color 1 Color 2 Color 3 Color 4 Color 5

Level 4
User Color
Dimmer <0-100> Shutter <0-255> Red <0-255> Green <0-255> Blue <0-255> Amber <0-255> White <0-255>

To define a User Color please press ENTER to access to main menu (level 1). While using the UP / DOWN arrows, please select the menu item “Stand Alone” and confirm by pressing ENTER.

User Manual

Select the item menu “User Color” by using the up/down controls and press ENTER. Using UP and DOWN select your desired preset number (Color 1 -5) and confirm with ENTER. Use UP and DOWN controls to select your desired color, confirm by ENTER and adjust the value by up and down controls between 000-255 and confirm all entries with ENTER. With dimmer you can adjust the allover brightness of your User Color. Shutter allows several strobe effects. Once your color mix is ready, jump back by ESC. Your individual color is stored under the selected color preset now.
*Note: All five User Colors are also available by DMX at Color Macro channel.
For detailed information please see Color Macro Chart at the end of this manual. Using UP/DOWN arrows at homescreen the Color Macros can be changed according to the list.
Shutter: Please see detailed explanation for strobe effects inside DMX chart at the end of this manual.

Color Settings* Here at “Color Settings” you can chose your preferred working color mode for all Stand Alone modes. Either Color Calibration or RAW. Chose Color Calibration if the fixture should work accroding to the settings at Color Calibration, either Full Calibration or CCT Calibration, RAW works according to the settings at RAW Balance, either RAW or User Calibrated.

Level 1

Level 2

Level 3

Stand Alone Mode

Color Settings

DMX Mode Stand Alone Slave Settings System Info

Stop Stand Alone Auto Color Macro Quick Color Tunable White User Color Color Settings Master

Color Calibration RAW

Master* If you want to set up a Master-Slave-System, select “On” at the fixture, that should be the Master and controls all connected Slaves. Keep this “Off”, if you don´t need it to prevent DMX collisions.

Level 1
Menu
DMX Mode Stand Alone Slave Settings System Info

Level 2
Stand Alone Mode
Stop Stand Alone Auto Color Macro Quick Color Tunable White User Color Color Settings Master

Level 3
On Off

Color Settings

User Manual

5.4.4 Slave Mode* Slave Mode allows same model fixtures to be controlled by the “Master” fixture via DMX). The “Master” device should run in Stand Alone mode, all “Slave” devices should set to “Slave”.

Level 1

DMX Mode Stand Alone Slave Settings System Info

To select “Slave” please press ENTER to access to main menu (level 1). While using the UP / DOWN arrows, please select the menu item “Slave” and confirm by pressing ENTER. Now this unit is set to “Slave”. Please connect the slave and the master devices (same model) with a DMX cable and enable one of your preferred standalone mode on the master device. Once the Stand Alone mode is activated all slave devices will follow the master device.
Note: All devices should use same software version. Once Stand Alone mode is disabled at Master unit the display of Slave unit starts to blink.

5.4.5 Settings
Level 1 Menu
DMX Mode Stand Alone Slave Settings System Info
Main Menu Menu level 2

Menu level 3 Display Flip

Display

Backlight

Settings

Auto Lock

Startup Mode (using last adjustments of specific Standalone Modes)

DMX Auto Color Macro Quick Color Tunable White User Color

Menu level 4 <on/off> <on/off>
<on/off>

Description On= Flip control panel display by 180° (e.g. for overhead installation) Off= normal control panel display On= controls permanent on, display itself will deactivate after 60 minues of incativity Off= controls and display deactivation after approximately 1 minute of inactivity On= Automatically locks the controls after approximately 1 minute of inactivity. After attempted input the display shows: ,,Locked!” Unlock process: press arrows up, down, up, down consecutively
Select your default operating mode when fixture is powered on
24

User Manual

Main Menu Menu level 2 DMX Fail
Dimmer Curve

Menu level 3 Hold Blackout Emergency Light Linear
Exponential
Logarithmic

S-Curve

Dimmer Response

LED Medium Halogen

Redshift

On / Off

Settings

Color Calibration (affetcs to corresponding DMX modes and Stand Alone)

Full Calibration CCT Calibration

RAW

RAW Balance (affects RAW Mode in DMX and Stand Alone Modes

User Calibration

RAW Balance (affects RAW Mode in DMX and Stand Alone Modes

User Calibration

Menu level 4
On= Activates Redshift, Off= Deactivates Redshift
Red 1 <0-255> Green 1 <0-255> Blue 1 <0-255> Amber 1 <0-255> White 1 <0-255> Red 2 <0-255> Green 2 <0-255> Blue 2 <0-255> Amber 2 <0-255> White 2 <0-255> Red 3 <0-255> Green 3 <0-255> Blue 3 <0-255> Amber 3 <0-255> White 3 <0-255> Red 4 <0-255> Green 4 <0-255> Blue 4 <0-255> Amber 4 <0-255> White 4 <0-255>

Description Hold= last command retains Blackout= Activates Blackout Emergency Light= Fixtures changes to 5600K Linear= Light intensity increases linear with DMX value Exponential= Light intensity can be set more smooth at lower DMX values and broadly at higher DMX values. Light intensity can be broadly adjusted at lower DMX values and more smooth at higher DMX values Light intensity can be adjusted smoothly at lower and higher DMX values and broadly at medium DMX values The LED responds abruptly to it´s DMX values The LED responds with medium delay to DMX value changes at brightness The LED responds similar to a halogen fixture with soft changes at brightness. Redshift function simulate traditional halogen fixtures while dimming down. Redshift affects only between 2700-3500K. CCT and RGB color calibration available for perfect color consistency from unit to unit Only CCT Calibration, but RAW colors for White color consistency from unit to unit, but maximum saturation on colors R,G,B,A,W with maximum value of brightness
individual color calibration for R,G,B,A,W
individual color calibration for R,G,B,A,W

User Manual

Main Menu Menu level 2 LED Frequency

Fan

Settings

Invert Mapping

Transfer Configuration
LED Mode

USB Update

Factory / User Reset

Menu level 3 800 Hz 1200 Hz 2000 Hz 3600 Hz 12000 Hz 25000 Hz Auto Silent Fan Off Max. Power Off CW
CCW Including DMX Address Without DMX Address Illumination Boost Yes No
Factory Reset
User Reset

Menu level 4

Description

Select preferred LED PWM frequency

Adjust fan speed relative to internal fixture temperature
Low fan speed for silent operation
Fan Off
High fan speed for maximum cooling effect
No Pixel Invert
Inverts the Pixel Layout clockwise, Pixel #3 becomes Pixel #1
Inverts the Pixel Layout counter-clockwise, Pixel #2 becomes Pixel #1

Transfer the same menu settings of this fixture to all the other in daisy chain (same model)

Normal output for constant illumination

Boost for temporarily highest output for blinder and strobe effects

Run firmware update via USB port

Do not run firmware update via USB port

Are you sure to reset? Confirm by pressing ENTER, cancel with ESC

Restores all factory defaults including User Colors, but no User defaults.

Are you sure to reset? Confirm by pressing ENTER, cancel with ESC

Restores all User Reset according to the User Preset List. Timer Function and DMX adress restore to Factory default. Once User Reset is activated a fixture self test will start.

User Manual

Main Menu Menu level 2

Settings

Factory / User Reset

Menu level 3 User Reset List

Menu level 4

Menu Level 5

1CH DWE, 2CH DWE, 4-1CH DWE, 4-2CH DWE, 9CH DWE+, 8CH STROBE, 12CH RGB, 10CH BASIC RGB, 14CH BASIC RGB, 21CH SECTION RGB 21CH, 22CH Comp RGB STANDARD RGB, 38CH STANDARD RGB, 40CH EXTENDED RGB, 57CH EXTENDED RGB, 20CH DIRECT, 12CH DIRECT, 29CH DIRECT, 48CH DIRECT, 73CH DIRECT

Display Flip

Backlight

Auto Lock

Startup Mode

DMX Fail

Dimmer Curve

<Linear, Exponential, Logarithmic, S-Curve>

Dimmer Response

<LED, Medium, Halogen>

Redshift

LED Frequency

<800Hz, 1200Hz, 2000Hz, 3600Hz, 12000Hz, 25000Hz>

Color Calibration

Full Calibration / CCT Calibration

RAW Balance

RAW / User Calibration

Fan

<Auto, Silent, Studio, Fan Off, Max. Power>

Invert Mapping

<off, CW, CCW>

Transfer Configuration

LED Mode

<Illumination, Boost>

USB Update

Description
Select your User Reset defaults

User Manual

Pixel Arrangement

OFF PIXEL 1 PIXEL 3

PIXEL 2 PIXEL 4

CW PIXEL 3 PIXEL 4

PIXEL 1 PIXEL 2

CCW PIXEL 2 PIXEL 1

PIXEL 4 PIXEL 3

Dimmer Curves LINEAR

EXPONENTIAL

LOGARITHMIC

S-CURVE

5.4.6 System Info
Level 1
Menu
DMX Mode Stand Alone Slave Settings System Info

Main Menu Menu level 2 Firmware Version Serial Number RDM UID

System Info

Temperatures Power on Time

LED on Time Errors

Menu level 3
vx.xx
202xxxxxxxx
0X6a6axxxxxxxx
LED 1: Celsius/Fahrenheit : XXX°C / XXX °F LED 2: Celsius/Fahrenheit : XXX°C / XXX °F LED 3: Celsius/Fahrenheit : XXX°C / XXX °F LED 4: Celsius/Fahrenheit : XXX°C / XXX °F
Total: LED 1: xxxxxhours LED 2: xxxxxhours LED 3: xxxxxhours LED 4: xxxxxhours
Total: xxxxxhours
Errors information

Menu level 4 Display installed firmware version Display unique RDM ID for identification Display LED 1-4 temperature by celsius and fahrenheit
Display fixture total power on time
Display LED 1-4 total power on time Display error codes
28

User Manual
6. ACCESSORIES

Yoke 4.3 Art.: 13907101

Floor Extension Art.: 13907201

Rigging Bracket G2 Art.: 13907411

Omega Bracket ST Art.: 90900002

Floor Bracket Art.: 13908501

Amptown Case 4 pcs. / 8 pcs. Art.: 13907411 Amptown Case 2 pcs / 4 pcs Art.: 13907511

CS Case 5 pcs B2 / S2. Art.: 13908201 CS Case 5 pcs B4 Art.: 13908301

Line Array Fly Bar Art.: 13909501

Line Array Side Bracket Set Art.: 13909601

Line Array Backbone 4 Art.: 13909701

Line Array Backbone 2+2 Art.: 13909801

Line Array Floor Bracket Art.: 13909901

User Manual
7. TECHNICAL DATA / DIAGRAMS
7.1 Technical drawings and measurements
30

User Manual
7.2 IP Rating ROXX products conform to officially classified IP standard levels. CLUSTER B4 FC is rated to IP65 when using the covers for the housing parts. IP stands for Ingress Protection and IP65, according to classified standard, means shielded against dust and high-pressure jets of water from any side.
Ingress Protection
65

Protected against a solid object exceeding 50mm, for example,

a hand.

Protected against a solid object exceeding 12.5mm, for example,

a finger.

Protected against a solid object exceeding 2.5mm, for example,

a screwdriver.

Protected against a solid object exceeding 1mm, for example, a wire.

Dust protected. Limited ingress of dust allowed. Does not affect the

operation of the device.

Dustproof. No infiltration of dust.

Protected against vertically falling water drops. Limited infiltration is

permitted.

Protected against vertically falling water drops when the enclosure is

tilted up to 15 degrees from the ver-

tical. Limited infiltration is permitted.

Protected against water spray up to 60 degrees from the vertical. Limited

infiltration is permitted.

Protected against splashes of water from all directions. Limited infiltration

is permitted.

Protected against water jets. Limited infiltration is permitted.

Protected against strong water jets. Limited infiltration is permitted.

Protected against the impact of being immersed in water between

15cm and 1m for 30 minutes.

Protected against the impact of being immersed in water under pres-

sure for prolonged periods of time.

User Manual

7.3 Technical Data

Photometrics LED expected lifetime Lightsource Type of optical system LED PWM Frequency Beam angles (50%) Maximum Field angles (10%) Color temperature range Efficancy (max) CRI/RA Luminous flux illuminance Lux @ 1m / 3,3ft (@ 2900K) illuminance Lux @ 3m / 9,8ft (@ 2900K) illuminance Lux @ 5m / 16,4ft (@ 2900K) illuminance Lux @ 7m / 23,0ft (@ 2900K) illuminance Lux @ 10m / 32,8ft (@ 2900K) Thermal Characteristics Cooling Humidity (max.) Temperature range, Operating Temperature range, Start-up Temperature range, Storage Thermal Protection Electrical Data AC Power, max AC Power, nominal Electrical protection Max power consumption Constant power consumption Power Max. Out Power Linking @ Max Power Consumption (Boost Mode) Power Linking @ Constant Power Consumption (Illumination Mode) Power Factor Power Supply Unit

50.000 hours 4x 300W Red, Green, Royal Blue, Amber, Warm-White Reflector with Compound Eye Lens selectable 800Hz, 1200Hz, 2000Hz, 3600Hz, 12kHz, 25kHz 50° 87° 2.000-10.000K 22,62 lm/W 90 @ 5600K / 86 @ 2900K 28.300 lm 33265lx / 3090fcd 3695lx / 343fcd 1330lx / 124fcd 675lx / 63fcd 333lx / 31fcd
Active, Forced Air, Temperature-regulated 95% -40°C to 45°C -20°C to 45°C -40°C to 80°C Automatic overtemperature protection
90 285V 50/60Hz 100 240V 50/60Hz Overload protection with automatic recover 1250W 400W 9A @ 230V / 2A @ 120V
1 unit @ 230V / 0 unit @ 120V
7 units @ 230V / 2 units @ 120V
0.925 PF (230V) / 0.993 PF (120V) Inbuilt auto-ranging electronic switch-mode

User Manual
7.3 Technical Data
Operator & Controller
DMX Functions
DMX channels
DMX modes Protocol RDM ANSI E1.20 Setting and addressing Standalone mode Wireless DMX Indicator Controls Strobe DMX I/O Power In USB Firmware Update Dimensions & Weight IP class IK class Body material Lens material Net dimensions (w x h x d) Net dimensions inches Net weight (incl. Yoke) Tilt Tilt Locking System Included / Optional Included items Optional Accessories Color options Installation
Mounting point by Yoke (included)
Mounting point on fixture Mounting point with otional Rigging Bracket Orientation Rigging possibilities Safety features Minimum distance from flammable materials

Master Dimmer, Master Dimmer Fine, Shutter, Duration, Dimmer 1-4, Dimmer 1-4 Fine, Red 1-4, Red 1-4 Fine, Green 1-4, Blue 1-4, Blue Fine 1-4, Amber 1-4, WarmWhite 1-4, CTC 1-4, Tint 1-4, Color Macro 1-4, Color Macro Crossfade 1-4, Effect, Dimmer Curve, Dimmer Response, Redshift, Device Settings 1CH DWE, 2 CH DWE, 4-1CH DWE, 4-2CH DWE, 9CH DWE+, 8CH STROBE, 12CH RGB, 10CH BASIC RGB, 14CH BASIC RGB, 21CH SECTION RGB, 21CH STANDARD RGB (default), 22CH Comp RGB, 38CH STANDARD RGB, 40CH EXTENDED RGB, 57CH EXTENDED RGB, 20CH DIRECT, 12CH DIRECT, 29CH DIRECT, 48CH DIRECT, 73CH DIRECT 20 USITT DMX512A Auto Program, Editor, Color Macro, Quick Color, Tunable White, User Color, Timer OLED graphical display / 4 controls Auto Program, Editor, Color Macro, Quick Color, Tunable White, User Color, Timer n.a. OLED graphical display 4 touch sensitive, backlighted controls 0-20Hz IP65 XLR 5-pin male/female TRUE1 compatible input & link-thru sockets IP65 USB socket IP65 XLR 5-pin male/female IP65 IK08 Aluminum, Nylon Tempered glass front 400 x 400 x 191mm 15,75 x 15,75 x 7,52 inches 16,2 kg (35,71lbs) 360° Locking system with toothing and angle indicator
Yoke 4.2, 2m Power Cable, Puk Yoke 4.3, Yoke Floor Extension, Rigging Bracket, Omega Bracket ST Black RAL 9004 (Standard) / Custom color any RAL (on request)
3x 13mm / 1/2″ holes, 1x centric TV Spigot attachement, 3x integrated Camlocks for Omega Brackets 1/4 turn Omega Bracket on top and rear side 2x 13mm / 1/2″ holes for Clamp fixation Any Hanging or ceiling / pendant mount
2x rear mount for safety wire 0,3 meters (11,8 inch)
33

User Manual

7.4 DMX-Charts / Color Macro Charts / CCT Chart

1CH DWE 2CH DWE 4-1CH DWE 4-2CH DWE 9CH DWE+ 8CH STROBE 12CH RGB 10CH BASIC RGB 14CH BASIC RGB 21CH SECTION RGB 21CH STANDARD RGB (default)

22CH Comp RGB 38CH STANDARD RGB 40CH EXTENDED RGB 57CH EXTENDED RGB 20CH DIRECT 12CH DIRECT 29CH DIRECT 48CH DIRECT 73CH DIRECT

1CH DWE (Calibrated)

Dimmer

4 5 6 7 8 9

2CH DWE (Calibrated)
Dimmer 1
Dimmer 2

4-1CH DWE (Calibrated) Dimmer 1 Dimmer 2 Dimmer 3
Dimmer 4

4-2CH DWE (Calibrated) Dimmer Dimmer Curve Dimmer Response
Redshift

9CH DWE+ (Calibrated) Master Dimmer Shutter Red
Green Blue CTC Dimmer Curve Dimmer Response Redshift

8CH STROBE (Calibrated) Master Dimmer Shutter Duration
Dimmer 1 Dimmer 2 Dimmer 3 Dimmer 4 CCT

User Manual

12CH RGB (Calibrated)

Red 1

Green 1

Blue 1

Red 2

Green 2

Blue 2

Red 3

Green 3

Blue 3

10 Red 4

11 Green 4

12 Blue 4

10CH BASIC RGB (Calibrated)
Master Dimmer Shutter Red Green Blue CTC Tint Color Macro Color Macro Crossfade Device Settings

14CH BASIC RGB (Calibrated)
Master Dimmer Master Dimmer Fine Shutter Red Red Fine Green Green Fine Blue Blue Fine CTC Tint Color Macro Color Macro Crossfade Device Settings

21CH SECTION RGB (Calibrated)
Dimmer 1 Red 1 Green 1 Blue 1 CTC 1 (affects RGB 1) Dimmer 2 Red 2 Green 2 Blue 2 CTC 2 (affects RGB 2) Dimmer 3 Red 3 Green 3 Blue 3 CTC 3 (affects RGB 3) Dimmer 4 Red 4 Green 4 Blue 4 CTC 4 (affects RGB 4) Device Settings

User Manual

21CH STANDARD RGB (Calibrated / default)

22CH Comp RGB (Calibrated)

Master Dimmer

Shutter

Dimmer 1

Red 1

Green 1

Blue 1

Dimmer 2

Red 2

Green 2

10 Blue 2

11 Dimmer 3

12 Red 3

13 Green 3

14 Blue 3

15 Dimmer 4

16 Red 4

17 Green 4

18 Blue 4

19 CTC (all)

20 Tint (all)

21 Device Settings

Dimmer 1 Red 1 Green 1 Blue 1 Dimmer 2 Red 2 Green 2 Blue 2 Shutter 1+2 CTC (affects RGB 1+2) Device Settings Dimmer 3 Red 3 Green 3 Blue 3 Dimmer 4 Red 4 Green 4 Blue 4 Shutter 3+4 CTC (affects RGB 3+4) Device Settings

38 CH STANDARD RGB 40CH EXTENDED RGB

(Calibrated)

57CH EXTENDED RGB (Calibrated)

Master Dimmer Master Dimmer Fine Shutter Dimmer 1 Dimmer 1 Fine Red 1 Red 1 Fine Green 1 Green 1 Fine Blue 1 Blue 1 Fine Dimmer 2 Dimmer 2 Fine Red 2 Red 2 Fine Green 2 Green 2 Fine Blue 2 Blue 2 Fine Dimmer 3 Dimmer 3 Fine Red 3 Red 3 Fine Green 3 Green 3 Fine Blue 3 Blue 3 Fine Dimmer 4 Dimmer 4 Fine Red 4 Red 4 Fine Green 4 Green 4 Fine Blue 4 Blue 4 Fine CTC (all) Tint (all) Device Settings

Master Dimmer Shutter Duration Dimmer 1 Red 1 Green 1 Blue 1 CTC 1 Tint 1 Color Macro 1 Color Macro Crossfade 1 Dimmer 2 Red 2 Green 2 Blue 2 CTC 2 Tint 2 Color Macro 2 Color Macro Crossfade 2 Dimmer 3 Red 3 Green 3 Blue 3 CTC 3 Tint 3 Color Macro 3 Color Macro Crossfade 3 Dimmer 4 Red 4 Green 4 Blue 4 CTC 4 Tint 4 Color Macro 4 Color Macro Crossfade 4 Effect Dimmer Curve Dimmer Response Redshift

Master Dimmer Master Dimmer Fine Shutter Duration Dimmer 1 Dimmer 1 Fine Red 1 Red 1 Fine Green 1 Green 1 Fine Blue 1 Blue 1 Fine CTC 1 Tint 1 Color Macro 1 Color Macro Crossfade 1 Dimmer 2 Dimmer 2 Fine Red 2 Red 2 Fine Green 2 Green 2 Fine Blue 2 Blue 2 Fine CTC 2 Tint 2 Color Macro 2 Color Macro Crossfade 2 Dimmer 3 Dimmer 3 Fine Red 3 Red 3 Fine Green 3 Green 3 Fine Blue 3 Blue 3 Fine CTC 3 Tint 3 Color Macro 3

User Manual
CH 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57

38CH STANDARD RGB (Calibrated)

40CH EXTENDED RGB (Calibrated)
Device Settings

57CH EXTENDED RGB (Calibrated) Color Macro Crossfade 3 Dimmer 4 Dimmer 4 Fine Red 4 Red 4 Fine Green 4 Green 4 Fine Blue 4 Blue 4 Fine CTC 4 Tint 4 Color Macro 4 Color Macro Crossfade 4 Effect Dimmer Curve Dimmer Response Redshift Device Settings

User Manual

20CH DIRECT (RAW)

1 Red 1 2 Green 1 3 Blue 1 4 Amber 1 5 White 1 6 Red 2 7 Green 2 8 Blue 2 9 Amber 2 10 White 2 11 Red 3 12 Green 3

13 Blue 3

14 Amber 3 15 White 3 16 Red 4 17 Green 4 18 Blue 4 19 Amber 4 20 White 4 21 22

24 25 26 27 28 29 30 31 32

34 35 36 37

12CH DIRECT (RAW)

29CH DIRECT (RAW)

Master Dimmer

Shutter

Red

Dimmer 1

Green

Red 1

Blue

Green 1

Amber

Blue 1

White

Amber 1

CTC

White 1

Tint

Dimmer 2

Color Macro

Red 2

Color Macro Crossfade Green 2

Device Settings

Blue 2

Amber 2

White 2 Dimmer 3 Red 3 Green 3 Blue 3 Amber 3 White 3 Dimmer 4 Red 4

Green 4

Blue 4 Amber 4 White 4 CTC (all) Tint (all) Device Settings

48CH DIRECT (RAW) Master Dimmer Shutter Duration Dimmer 1 Red 1 Green 1 Blue 1 Amber 1 White 1 CTC 1 Tint 1 Color Macro 1 Color Macro Crossfade 1 Dimmer 2 Red 2 Green 2 Blue 2 Amber 2 White 2 CTC 2 Tint 2 Color Macro 2 Color Macro Crossfade 2 Dimmer 3 Red 3 Green 3 Blue 3 Amber 3 White 3 CTC 3 Tint 3 Color Macro 3 Color Macro Crossfade 3 Dimmer 4 Red 4 Green 4 Blue 4

73CH DIRECT (RAW)
Master Dimmer Master Dimmer Fine Shutter Duration Dimmer 1 Dimmer 1 Fine Red 1 Red Fine 1 Green 1 Green Fine 1 Blue 1 Blue Fine 1
Amber 1
Amber Fine 1 White 1 White Fine 1 CTC 1 Tint 1 Color Macro 1 Color Macro Crossfade 1 Dimmer 2 Dimmer 2 Fine
Red 2
Red Fine 2 Green 2 Green Fine 2 Blue 2 Blue Fine 2 Amber 2 Amber Fine 2 White 2 White Fine 2
CTC 2
Tint 2 Color Macro 2 Color Macro Crossfade 2 Dimmer 3

User Manual

20CH DIRECT (RAW)

44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73

12CH DIRECT (RAW)

29CH DIRECT (RAW)

48CH DIRECT (RAW) Amber 4 White 4 CTC 4 Tint 4 Color Macro 4 Color Macro Crossfade 4 Effect Dimmer Curve Dimmer Response Redshift Device Settings

73CH DIRECT (RAW) Dimmer 3 Fine Red 3 Red Fine 3 Green 3 Green Fine 3
Blue 3
Blue Fine 3 Amber 3 Amber Fine 3 White 3 White Fine 3 CTC 3 Tint 3 Color Macro 3 Color Macro Crossfade 3 Dimmer 4 Dimmer 4 Fine Red 4 Red Fine 4 Green 4 Green Fine 4 Blue 4 Blue Fine 4 Amber 4 Amber Fine 4 White 4 White Fine 4 CTC 4 Tint 4 Color Macro 4 Color Macro Crossfade 4 Effect Dimmer Curve Dimmer Response Redshift Device Settings

User Manual

1CH DWE (Calibrated / according to selected Tunable White settings at Stand Alone Mode, default 2900K)

CH Function

Value

Setting

Remark

1 Dimmer

000-255

0 – 100%

Default 0

2CH DWE (Calibrated / according to selected Tunable White settings at Stand Alone Mode, default 2900K)

CH Function

Value

Setting

Remark

Dimmer 1 (affects eye 1 + 3)

000-255

0 – 100%

Dimmer 2 (affects eye 2 + 4)

000-255

0 – 100%

Default 0 0

4-1CH DWE (Calibrated / according to selected Tunable White settings at Stand Alone Mode, default 2900K)

CH Function

Value

Setting

Remark

Default

1 Dimmer 1

000-255

0 – 100%

2 Dimmer 2

000-255

0 – 100%

3 Dimmer 3

000-255

0 – 100%

4 Dimmer 4

000-255

0 – 100%

4-2CH DWE (Calibrated / according to selected Tunable White settings at Stand Alone Mode, default 2900K)

CH Function

Value

Setting

Remark

Default

1 Dimmer

000-255

0 – 100%

000-51

No Function – Current Preset from Menu Settings

052-101

Linear Dimmer Curve

2 Dimmer Curve

102-152

Exponential Dimmer Curve

153-203

Logarithmic Dimmer Curve

204-255

S-Curve Dimmer Curve

000-063

No Function – Current Preset from Menu Settings

3 Dimmer Response 064-127

LED / fast

128-191

Medium

192-255

Halogen / slow

4 Redshift

000-84 085-170 171-255

No Function – Current Preset from Menu

Settings

Redshift affects only

Redshift Off

between CCT 2700- 0 3500K

Redshift On

9CH DWE+ (Calibrated) CH Function 1 Master Dimmer
2 Shutter

Value 000-255 000 – 019 020 – 024 025 – 064 065 – 069 070 – 084

Setting 0 – 100% Shutter close Shutter open Strobe 1 (fast slow) Shutter open Strobe 2: opening pulse (fast slow)

Remark

Default 0
20
40

User Manual

085 – 089 090 – 104 105 – 109 110 – 124 125 – 129

130 – 144

145 – 149

2 Shutter

150 – 164
165 – 169 170 – 184 185 – 189

190 – 204

3 Red 4 Green 5 Blue

205 – 209 210 – 224 225 – 229 230 – 244 245 – 255 000-255 000-255 000-255 000 – 004

005-226

6 CTC (affects RGB) 182-182 226-226

227-255

000-51

7 Dimmer Curve

052-101 102-152 153-203 204-255

000-063

8 Dimmer Response 064-127 128-191 192-255

9 Redshift

000-84 085-170 171-255

Shutter open

Strobe 3: closing pulse (fast slow)

Shutter open

Strobe 4: random strobe (fast slow)

Shutter open

Strobe 5: random opening pulse (fast slow)

Shutter open

Strobe 6:random closing pulse (fast slow)
20 Shutter open

Strobe 7: burst pulse (fast slow)

Shutter open

Strobe 8: random burst pulse (fast slow)

Shutter open

Strobe 9:sine wave (fast slow)

Shutter open

Strobe 10: burst (fast slow)

Shutter open

0 – 100%

255

0 – 100%

255

0 – 100%

255

2900K

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

according to CTC chart 0

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

No Function – Current Preset from Menu Settings

Linear Dimmer Curve

Exponential Dimmer Curve

Logarithmic Dimmer Curve

S-Curve Dimmer Curve

No Function – Current Preset from Menu Settings

LED / fast

Medium

Halogen / slow

No Function – Current Preset from Menu

Settings

Redshift affects only

Redshift Off

between CCT 2700- 0 3500K.

Redshift On

User Manual

8CH STROBE MODE (Calibrated)

CH Function

Value

1 Master Dimmer

000-255

000 – 019

020 – 024

025 – 064

065 – 069

070 – 084

085 – 089

090 – 104

105 – 109

110 – 124

125 – 129

2 Shutter

130 – 144 145 – 149

150 – 164

165 – 169

170 – 184

185 – 189

190 – 204

205 – 209

210 – 224

225 – 229 230 – 244 245 – 255

3 Duration

000-255

4 Dimmer 1 5 Dimmer 2 6 Dimmer 3 7 Dimmer 4

000-255 000-255 000-255 000-255 000 – 004

005-226

8 CCT

182-182 226-226

227-255

Setting

Remark

Default

0 – 100%

Shutter close

Shutter open

Strobe 1 (fast slow)

Shutter open

Strobe 2: opening pulse (fast slow)

Shutter open

Strobe 3: closing pulse (fast slow)

Shutter open

Strobe 4: random strobe (fast slow)

Shutter open

Strobe 5: random opening pulse (fast slow)
20 Shutter open

Strobe 6: random closing pulse (fast slow)

Shutter open

Strobe 7: burst pulse (fast slow)

Shutter open

Strobe 8: random burst pulse (fast slow)

Shutter open

Strobe 9:sine wave (fast slow)

Shutter open

Strobe 10: burst (fast slow)

Shutter open

0 – 100% (0ms – 510ms)

only affects to channel 2 – Strobe 1 025-064

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

5600K

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

according to CTC chart 0

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

User Manual

12CH RGB (Calibrated) CH Function 1 Red 1 2 Green 1 3 Blue 1 4 Red 2 5 Green 2 6 Blue 2 7 Red 3 8 Green 3 9 Blue 3 10 Red 4 11 Green 4 12 Blue 4

Value 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255

10CH BASIC RGB (Calibrated)

CH Function

Value

1 Master Dimmer

000-255

000 – 019

020 – 024

025 – 064

065 – 069

070 – 084

2 Shutter

085 – 089 090 – 104

105 – 109

110 – 124

125 – 129

130 – 144

145 – 149

150 – 164

2 Shutter

165 – 169 170 – 184 185 – 189 190 – 204 205 – 209 210 – 224 225 – 229 230 – 244 245 – 255

Setting 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100%

Remark

Setting

Remark

0 – 100%

Shutter close

Shutter open

Strobe 1 (fast slow)

Shutter open

Strobe 2: opening pulse (fast slow)

Shutter open

Strobe 3: closing pulse (fast slow)

Shutter open

Strobe 4: random strobe (fast slow)

Shutter open

Strobe 5: random opening pulse (fast slow)

Shutter open

Strobe 6: random closing pulse (fast slow)

Shutter open

Strobe 7: burst pulse (fast slow)

Shutter open

Strobe 8: random burst pulse (fast slow)

Shutter open

Strobe 9: sine wave (fast slow)

Shutter open

Strobe 10: burst (fast slow)

Shutter open

Default 0 0 0 0 0 0 0 0 0 0 0 0
Default 0
20
20
43

User Manual

3 Red 4 Green 5 Blue

000-255 000-255 000-255 000 – 004

005-226

6 CTC (affects RGB) 182-182 226-226

227-255

Tint 7 (affects CTC and
RGB)

001-127 128-128 129-255

Color Macro (override RGB/CTC)

000 – 005

Color Macro Cross- 006-105

fade (Transition Time between

106-214

Color Macros)

215-244

245-255

000-029

030-034 035-039 040-044 045-049 050-054

055-059

Device Settings 10 (please see
remark *1)

060-064 065-069 070-074

075-079 080-084 085-089 090-094 095-099

100-104 105-109

0 – 100%

255

0 – 100%

255

0 – 100%

255

5600K

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

according to CTC chart 0

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

Tint (affects CTC and RGB)

no function

Magenta -> Neutral

Neutral

Neutral -> Green

Please see ROXX color macro chart

No function

0,1s – 10s (0,1s steps)

11s – 119s (1s steps)

2m – 4m50s (10s steps)

5m – 15m (1m steps)

No function

Display Backlight On (hold 3s)
Display Backlight Off (hold 3s)
No function
DMX Fail Blackout (hold 3s)
DMX Fail Hold (hold 3s)
DMX Fail – Emergency Light (hold 3s)
No function
Linear Dimmer Curve (hold 1,5s) 0
Exponential Dimmer Curve (hold 1,5s)
Logarithmic Dimmer Curve (hold 1,5s)
S-Curve Dimmer Curve (hold 1,5s)
No function
LED (Fast) Dimmer Response (hold 1,5s)
Medium Dimmer Response (hold 1,5s)
Halogen (Slow) Dimmer Response (hold 1,5s)
No function

User Manual

Device Settings 10 (please see
remark *1)

110-114
115-119 120-124 125-129 130-134 135-139 140-144 145-149 150-154 155-159 160-164 165-169 170-174 175-179 180-184 185-189 190-194 195-199 200-204 205-209 210-214 215-219 220-224 225-229 230-234
235-239

240-244 245-255

Redshift On (hold 1,5s / affects only between 2700-3500K )

Redshift Off (hold 1,5s)

No function

Full Calibration (Colors & CCT / hold 3s)

CCT Calibration (RAW Colors / hold 3s)

No function

LED Frequency 800Hz (hold 3s)

LED Frequency 1200Hz (hold 3s)

LED Frequency 2000Hz (hold 3s)

LED Frequency 3600Hz (hold 3s)

LED Frequency 12kHz (hold 3s)

LED Frequency 25kHz (hold 3s)

No function

Fan Auto (hold 3s)

Fan Silent (hold 3s)

Fan Off (hold 3s)

Fan High Power (hold 3s)

No function

Invert Mapping Off (hold 3s)

Invert Mapping CW (hold 3s)

Invert Mapping CCW (hold 3s)

No function

LED Mode – Illumination (hold 1,5s)

LED Mode – Boost (hold 1,5s)

No function

Factory Reset (hold 3s)

Reset only starts if Shutter channel is set to DMX 250

User Reset (hold 3s)

Reset only starts if Shutter channel is set to DMX 250 / no selftest by DMX

No function

User Manual

14CH BASIC RGB (Calibrated)

CH Function

Value

1 Master Dimmer

000-255

2 Master Dimmer Fine 000-255

000 – 019

020 – 024

025 – 064

065 – 069

070 – 084

085 – 089

090 – 104

105 – 109

110 – 124

125 – 129

3 Shutter

130 – 144 145 – 149

150 – 164

165 – 169 170 – 184 185 – 189

190 – 204

4 Red 5 Red Fine 6 Green 7 Green Fine 8 Blue 9 Blue Fine

205 – 209 210 – 224 225 – 229 230 – 244 245 – 255 000-255 000-255 000-255 000-255 000-255 000-255 000 – 004

005-226

10 CTC (affects RGB)

182-182 226-226

227-255

Setting

Remark

Default

0 – 100%

Shutter close

Shutter open

Strobe 1 (fast slow)

Shutter open

Strobe 2: opening pulse (fast slow)

Shutter open

Strobe 3: closing pulse (fast slow)

Shutter open

Strobe 4: random strobe (fast slow)

Shutter open

Strobe 5: random opening pulse (fast slow)

Shutter open

Strobe 6: random closing pulse (fast slow)

Shutter open

Strobe 7: burst pulse (fast slow)

Shutter open

Strobe 8: random burst pulse (fast slow)

Shutter open

Strobe 9: sine wave (fast slow)

Shutter open

Strobe 10: burst (fast slow)

Shutter open

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

5600K

according to CTC chart

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

User Manual

Tint 11 (affects CTC and
RGB)

0 001-127 128-128 129-255

Color Macro (override RGB/CTC)

000 – 005

Color Macro Cross- 006-105

fade (Transition Time between Color

106-214

Macros)

215-244

245-255

000-029

030-034

035-039

040-044

045-049

050-054

055-059

060-064

065-069

070-074

075-079

080-084

085-089

090-094

Device Settings 14 (please see
remark *1)

095-099 100-104 105-109

110-114

115-119 120-124 125-129 130-134 135-139 140-144 145-149 150-154 155-159 160-164 165-169 170-174

no function Magenta -> Neutral Neutral Neutral -> Green
Please see ROXX color macro chart
no function 0,1s – 10s (0,1s steps) 11s – 119s (1s steps) 2m – 4m50s (10s steps) 5m – 15m (1m steps) No function Display Backlight On (hold 3s) Display Backlight Off (hold 3s) No function DMX Fail Blackout (hold 3s) DMX Fail Hold (hold 3s) DMX Fail – Emergency Light (hold 3s) No function Linear Dimmer Curve (hold 1,5s) Exponential Dimmer Curve (hold 1,5s) Logarithmic Dimmer Curve (hold 1,5s) S-Curve Dimmer Curve (hold 1,5s) No function LED (Fast) Dimmer Response (hold 1,5s) Medium Dimmer Response (hold 1,5s) Halogen(Slow) Dimmer Response (hold 1,5s) No function Redshift On (hold 1,5s / affects only between 2700-3500K ) Redshift Off (hold 1,5s) No function Full Calibration (Colors & CCT / hold 3s) CCT Calibration (RAW Colors / hold 3s) No function LED Frequency 800Hz (hold 3s) LED Frequency 1200Hz (hold 3s) LED Frequency 2000Hz (hold 3s) LED Frequency 3600Hz (hold 3s) LED Frequency 12kHz (hold 3s) LED Frequency 25kHz (hold 3s) No function

0 0 0
0
47

User Manual

Device Settings 14 (please see
remark *1)

175-179 180-184 185-189 190-194 195-199 200-204 205-209 210-214 215-219 220-224 225-229 230-234
235-239

240-244

245-255

21CH SECTION RGB (Calibrated)

CH Function

Value

1 Dimmer 1

000-255

2 Red 1

000-255

3 Green 1

000-255

4 Blue 1

000-255

000 – 004

CTC 1 (affects RGB 1)

005-226 182-182 226-226

227-255

6 Dimmer 2 7 Red 2 8 Green 2 9 Blue 2

000-255 000-255 000-255 000-255 000 – 004

CTC 2 (affects RGB 2)

005-226 182-182 226-226

227-255

11 Dimmer 3

000-255

Fan Auto (hold 3s) Fan Silent (hold 3s) Fan Off (hold 3s) Fan High Power (hold 3s) No function Invert Mapping Off (hold 3s) Invert Mapping CW (hold 3s) Invert Mapping CCW (hold 3s) No function LED Mode – Illumination (hold 1,5s) LED Mode – Boost (hold 1,5s) No function
Factory Reset (hold 3s)
User Reset (hold 3s)
No function

0
Reset only starts if Shutter channel is set to DMX 250 Reset only starts if Shutter channel is set to DMX 250 / no selftest by DMX

Setting

Remark

Default

0 – 100%

255

0 – 100%

5600K

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

according to CTC chart 0

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

0 – 100%

255

0 – 100%

5600K

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

according to CTC chart 0

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

0 – 100%

255

User Manual

12 Red 3 13 Green 3 14 Blue 3

CTC 3 (affects RGB 3)

16 Dimmer 4 17 Red 4 18 Green 4 19 Blue 4

CTC 4 (affects RGB 4)

Device Settings 21 (please see
remark *1)

000-255 000-255 000-255 000 – 004
005-226
182-182 226-226
227-255
000-255 000-255 000-255 000-255 000 – 004
005-226
182-182 226-226
227-255
000-029 030-034 035-039 040-044 045-049 050-054 055-059 060-064 065-069 070-074 075-079 080-084 085-089 090-094 095-099
100-104
105-109
110-114
115-119 120-124 125-129

0 – 100%

5600K

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

according to CTC chart 0

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

0 – 100%

255

0 – 100%

5600K

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

according to CTC chart 0

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

No function

Display Backlight On (hold 3s)

Display Backlight Off (hold 3s)

No function

DMX Fail Blackout (hold 3s)

DMX Fail Hold (hold 3s)

DMX Fail – Emergency Light (hold 3s)

No function

Linear Dimmer Curve (hold 1,5s)

Exponential Dimmer Curve (hold 1,5s)

Logarithmic Dimmer Curve (hold 1,5s) 0
S-Curve Dimmer Curve (hold 1,5s)

No function

LED (Fast) Dimmer Response (hold 1,5s)

Medium Dimmer Response (hold 1,5s)

Halogen(Slow) Dimmer Response (hold 1,5s)

No function

Redshift On (hold 1,5s / affects only between 2700-3500K )

Redshift Off (hold 1,5s)

No function

Full Calibration (Colors & CCT / hold 3s)

User Manual

Device Settings 21 (please see
remark *1)

130-134 135-139 140-144 145-149 150-154 155-159 160-164 165-169 170-174 175-179 180-184 185-189 190-194 195-199 200-204 205-209 210-214 215-219 220-224 225-229 230-234 235-239 240-255

CCT Calibration (RAW Colors / hold 3s)

No function

LED Frequency 800Hz (hold 3s)

LED Frequency 1200Hz (hold 3s)

LED Frequency 2000Hz (hold 3s)

LED Frequency 3600Hz (hold 3s)

LED Frequency 12kHz (hold 3s)

LED Frequency 25kHz (hold 3s)

No function

Fan Auto (hold 3s)

Fan Silent (hold 3s)

Fan Off (hold 3s)

Fan High Power (hold 3s)

No function

Invert Mapping Off (hold 3s)

Invert Mapping On (hold 3s)

No function

LED Mode – Illumination (hold 1,5s)

LED Mode – Boost (hold 1,5s)

No function

Factory Reset (hold 3s)

User Reset (hold 3s)

no self-test by DMX

No function

21CH STANDARD RGB (Calibrated / default)

CH Function

Value

1 Master Dimmer

000-255

000 – 019

020 – 024

025 – 064

065 – 069

070 – 084

085 – 089

090 – 104

2 Shutter

105 – 109 110 – 124

125 – 129

130 – 144

145 – 149

150 – 164

165 – 169

Remark

Default 0
20
50

User Manual

2 Shutter

3 Dimmer 1 4 Red 1 5 Green 1 6 Blue 1 7 Dimmer 2 8 Red 2 9 Green 2 10 Blue 2 11 Dimmer 3 12 Red 3 13 Green 3 14 Blue 3 15 Dimmer 4 16 Red 4 17 Green 4 18 Blue 4

CTC (affects RGB 1-4)

Tint (affects CTC and RGB 1-4)

Device Settings

(please see remark *1)

170 – 184 185 – 189
190 – 204
205 – 209 210 – 224 225 – 229 230 – 244 245 – 255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000 – 004
005-226
182-182 226-226
227-255
0 001-127 128-128 129-255 000-029 030-034 035-039 040-044 045-049 050-054
055-059

Strobe 7: burst pulse (fast slow)

Shutter open

Strobe 8: random burst pulse (fast slow)

Shutter open

Strobe 9: sine wave (fast slow)

Shutter open

Strobe 10: burst (fast slow)

Shutter open

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

5600K

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

according to CTC chart 0

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

no function

Magenta -> Neutral 0
Neutral

Neutral -> Green

No function

Display Backlight On (hold 3s)

Display Backlight Off (hold 3s)

No function

DMX Fail Blackout (hold 3s)

DMX Fail Hold (hold 3s)

DMX Fail – Emergency Light (hold 3s)

User Manual

Device Settings 21 (please see
remark *1)

060-064 065-069 070-074 075-079 080-084 085-089 090-094 095-099
100-104
105-109
110-114
115-119 120-124 125-129 130-134 135-139 140-144 145-149 150-154 155-159 160-164 165-169 170-174 175-179 180-184 185-189 190-194 195-199 200-204 205-209 210-214 215-219 220-224 225-229 230-234
235-239

240-244 245-255

No function

Linear Dimmer Curve (hold 1,5s)

Exponential Dimmer Curve (hold 1,5s)

Logarithmic Dimmer Curve (hold 1,5s)

S-Curve Dimmer Curve (hold 1,5s)

No function

LED (Fast) Dimmer Response (hold 1,5s)

Medium Dimmer Response (hold 1,5s)

Halogen(Slow) Dimmer Response (hold 1,5s)

No function

Redshift On (hold 1,5s / affects only between 2700-3500K )

Redshift Off (hold 1,5s)

No function

Full Calibration (Colors & CCT / hold 3s)

CCT Calibration (RAW Colors / hold 3s)

No function

LED Frequency 800Hz (hold 3s)

LED Frequency 1200Hz (hold 3s)

LED Frequency 2000Hz (hold 3s)

LED Frequency 3600Hz (hold 3s) 0
LED Frequency 12kHz (hold 3s)

LED Frequency 25kHz (hold 3s)

No function

Fan Auto (hold 3s)

Fan Silent (hold 3s)

Fan Off (hold 3s)

Fan High Power (hold 3s)

No function

Invert Mapping Off (hold 3s)

Invert Mapping CW (hold 3s)

Invert Mapping CCW (hold 3s)

No function

LED Mode – Illumination (hold 1,5s)

LED Mode – Boost (hold 1,5s)

No function

Factory Reset (hold 3s)

Reset only starts if Shutter channel is set to DMX 250

User Reset (hold 3s)

Reset only starts if Shutter channel is set to DMX 250 / no selftest by DMX

No function

User Manual

22CH Comp RGB (Calibrated)

CH Function

Value

Dimmer 1

000-255

Red 1

000-255

Green 1

000-255

Blue 1

000-255

Dimmer 2

000-255

Red 2

000-255

Green 2

000-255

Blue 2

000-255

000 – 019

020 – 024

025 – 064

065 – 069

070 – 084

085 – 089

090 – 104

105 – 109

110 – 124

125 – 129

Shutter 1+2

130 – 144 145 – 149

150 – 164

165 – 169

170 – 184

185 – 189

190 – 204

205 – 209

210 – 224

225 – 229

230 – 244

245 – 255

000 – 004

005-226

10 CTC (affects RGB 1+2) 182-182 226-226

227-255

000-029

030-034

035-039

Device Settings (please see remark *1)

040-044

045-049

050-054

055-059

Setting 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% Shutter close Shutter open Strobe 1 (fast slow) Shutter open Strobe 2: opening pulse (fast slow) Shutter open Strobe 3: closing pulse (fast slow) Shutter open Strobe 4: random strobe (fast slow) Shutter open Strobe 5: random opening pulse (fast slow) Shutter open Strobe 6:random closing pulse (fast slow) Shutter open Strobe 7: burst pulse (fast slow) Shutter open Strobe 8: random burst pulse (fast slow) Shutter open Strobe 9:sine wave (fast slow) Shutter open Strobe 10: burst (fast slow) Shutter open 5600K 2000K-6500K linear in 20-21K steps (please see detailed CTC chart) 5600K 6500K 6621K-10.000K linear in 120-121K steps (please see detailed CTC chart) No function Display Backlight On (hold 3s) Display Backlight Off (hold 3s) No function DMX Fail Blackout (hold 3s) DMX Fail Hold (hold 3s) DMX Fail – Emergency Light (hold 3s)

Remark according to CTC chart

Default 255 0 0 0 255 0 0 0
20
0
0
53

User Manual

060-064 065-069 070-074 075-079 080-084 085-089 090-094 095-099 100-104 105-109

110-114

115-119

120-124

125-129

130-134

135-139

140-144

145-149

Device Settings (please see remark *1) 150-154

155-159

160-164

165-169

170-174

175-179

180-184

185-189

190-194

195-199

200-204

205-209

210-214

215-219

220-224

225-229

230-234

235-239

240-255

12 Dimmer 3

000-255

13 Red 3

000-255

14 Green 3

000-255

15 Blue 3

000-255

16 Dimmer 4

000-255

17 Red 4

000-255

18 Green 4

000-255

19 Blue 4

000-255

No function

Linear Dimmer Curve (hold 1,5s)

Exponential Dimmer Curve (hold 1,5s)

Logarithmic Dimmer Curve (hold 1,5s)

S-Curve Dimmer Curve (hold 1,5s)

No function

LED (Fast) Dimmer Response (hold 1,5s)

Medium Dimmer Response (hold 1,5s)

Halogen(Slow) Dimmer Response (hold 1,5s)

No function

Redshift On (hold 1,5s / affects only between 2700-3500K )

Redshift Off (hold 1,5s)

No function

Full Calibration (Colors & CCT / hold 3s)

CCT Calibration (RAW Colors / hold 3s)

No function

LED Frequency 800Hz (hold 3s)

LED Frequency 1200Hz (hold 3s)

LED Frequency 2000Hz (hold 3s)

LED Frequency 3600Hz (hold 3s)

LED Frequency 12kHz (hold 3s)

LED Frequency 25kHz (hold 3s)

No function

Fan Auto (hold 3s)

Fan Silent (hold 3s)

Fan Off (hold 3s)

Fan High Power (hold 3s)

No function

Invert Mapping Off (hold 3s)

Invert Mapping On (hold 3s)

No function

LED Mode – Illumination (hold 1,5s)

LED Mode – Boost (hold 1,5s)

No function

Factory Reset (hold 3s)

User Reset (hold 3s)

no self-test by DMX

No function

0 – 100%

255

0 – 100%

255

0 – 100%

User Manual

20 Shutter 3+4

000 – 019 020 – 024 025 – 064 065 – 069 070 – 084 085 – 089 090 – 104 105 – 109 110 – 124 125 – 129 130 – 144 145 – 149 150 – 164 165 – 169 170 – 184 185 – 189 190 – 204 205 – 209 210 – 224 225 – 229 230 – 244 245 – 255 000 – 004

005-226

21 CTC (affects RGB 3+4) 182-182 226-226

227-255

000-029

030-034

035-039

040-044

045-049

050-054

055-059

060-064

Device Settings (please see remark *1)

065-069

070-074

075-079

080-084

085-089

090-094

095-099

100-104

105-109

Shutter close Shutter open

Strobe 1 (fast slow) Shutter open

Strobe 2: opening pulse (fast slow) Shutter open

Strobe 3: closing pulse (fast slow) Shutter open

Strobe 4: random strobe (fast slow) Shutter open

Strobe 5: random opening pulse (fast slow) 20
Shutter open

Strobe 6:random closing pulse (fast slow) Shutter open

Strobe 7: burst pulse (fast slow) Shutter open

Strobe 8: random burst pulse (fast slow) Shutter open

Strobe 9:sine wave (fast slow) Shutter open

Strobe 10: burst (fast slow)

Shutter open

5600K

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

according to CTC chart

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

No function

Display Backlight On (hold 3s)

Display Backlight Off (hold 3s)

No function

DMX Fail Blackout (hold 3s)

DMX Fail Hold (hold 3s)

DMX Fail – Emergency Light (hold 3s)

No function

Linear Dimmer Curve (hold 1,5s)

Exponential Dimmer Curve (hold 1,5s)

Logarithmic Dimmer Curve (hold 1,5s)

S-Curve Dimmer Curve (hold 1,5s)

No function

LED (Fast) Dimmer Response (hold 1,5s)

Medium Dimmer Response (hold 1,5s)

Halogen(Slow) Dimmer Response (hold 1,5s)

No function

User Manual

110-114

115-119

120-124

125-129

130-134

135-139

140-144

145-149

150-154

155-159

160-164

165-169

170-174

Device Settings (please see remark *1) 175-179

180-184

185-189

190-194

195-199

200-204

205-209

210-214

215-219

220-224

225-229

230-234

235-239

240-255

38CH STANDARD RGB (Calibrated)

CH Function

Value

1 Master Dimmer

000-255

2 Master Dimmer Fine 000-255

000 – 019

020 – 024

025 – 064

065 – 069

3 Shutter

070 – 084 085 – 089

090 – 104

105 – 109

110 – 124

Redshift On (hold 1,5s / affects only between 2700-3500K )

Redshift Off (hold 1,5s)

No function

Full Calibration (Colors & CCT / hold 3s)

CCT Calibration (RAW Colors / hold 3s)

No function

LED Frequency 800Hz (hold 3s)

LED Frequency 1200Hz (hold 3s)

LED Frequency 2000Hz (hold 3s)

LED Frequency 3600Hz (hold 3s)

LED Frequency 12kHz (hold 3s)

LED Frequency 25kHz (hold 3s)

No function

Fan Auto (hold 3s)

Fan Silent (hold 3s)

Fan Off (hold 3s)

Fan High Power (hold 3s)

No function

Invert Mapping Off (hold 3s)

Invert Mapping On (hold 3s)

No function

LED Mode – Illumination (hold 1,5s)

LED Mode – Boost (hold 1,5s)

No function

Factory Reset (hold 3s)

User Reset (hold 3s)

no self-test by DMX

No function

Remark

Default 0 0

User Manual

3 Shutter
4 Dimmer 1 5 Dimmer 1 Fine 6 Red 1 7 Red Fine 1 8 Green 1 9 Green Fine 1 10 Blue 1 11 Blue Fine 1 12 Dimmer 2 13 Dimmer 2 Fine 14 Red 2 15 Red Fine 2 16 Green 2 17 Green Fine 2 18 Blue 2 19 Blue Fine 2 20 Dimmer 3 21 Dimmer 3 Fine 22 Red 3 23 Red Fine 3 24 Green 3 25 Green Fine 3 26 Blue 3 27 Blue Fine 3 28 Dimmer 4 29 Dimmer 4 Fine 30 Red 4 31 Red Fine 4

125 – 129
130 – 144
145 – 149
150 – 164
165 – 169 170 – 184 185 – 189
190 – 204
205 – 209 210 – 224 225 – 229 230 – 244 245 – 255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255

Shutter open Strobe 5: random opening pulse (fast slow) Shutter open Strobe 6:random closing pulse (fast slow) Shutter open Strobe 7: burst pulse (fast slow) Shutter open Strobe 8: random burst pulse (fast slow) Shutter open Strobe 9:sine wave (fast slow) Shutter open Strobe 10: burst (fast slow) Shutter open 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100%

20
255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255
57

User Manual

32 Green 4 33 Green Fine 4 34 Blue 4 35 Blue Fine 4

CTC (affects RGB 1-4)

Tint (affects CTC and RGB 1-4)

Device Settings 38 (please see
remark *1)

000-255 000-255 000-255 000-255 000 – 004
005-226
182-182 226-226
227-255
0 001-127 128-128 129-255 000-029 030-034 035-039 040-044 045-049 050-054 055-059 060-064 065-069 070-074 075-079 080-084 085-089 090-094 095-099
100-104
105-109
110-114
115-119 120-124 125-129 130-134 135-139 140-144 145-149 150-154 155-159

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

5600K

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

according to CTC chart 0

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

no function

Magenta -> Neutral 0
Neutral

Neutral -> Green

No function

Display Backlight On (hold 3s)

Display Backlight Off (hold 3s)

No function

DMX Fail Blackout (hold 3s)

DMX Fail Hold (hold 3s)

DMX Fail – Emergency Light (hold 3s)

No function

Linear Dimmer Curve (hold 1,5s)

Exponential Dimmer Curve (hold 1,5s)

Logarithmic Dimmer Curve (hold 1,5s)

S-Curve Dimmer Curve (hold 1,5s)

No function

LED (Fast) Dimmer Response (hold 1,5s) 0
Medium Dimmer Response (hold 1,5s)

Halogen (Slow) Dimmer Response (hold 1,5s)

No function

Redshift On (hold 1,5s / affects only between 2700-3500K )

Redshift Off (hold 1,5s)

No function

Full Calibration (Colors & CCT / hold 3s)

CCT Calibration (RAW Colors / hold 3s)

No function

LED Frequency 800Hz (hold 3s)

LED Frequency 1200Hz (hold 3s)

LED Frequency 2000Hz (hold 3s)

LED Frequency 3600Hz (hold 3s)

User Manual

Device Settings 38 (please see
remark *1)

160-164 165-169 170-174 175-179 180-184 185-189 190-194 195-199 200-204 205-209 210-214 215-219 220-224 225-229 230-234
235-239

240-244

245-255

40CH EXTENDED RGB (Calibrated)

CH Function

Value

1 Master Dimmer

000-255

000 – 019

020 – 024

2 Shutter

025 – 064

065 – 069

070 – 084

085 – 089

090 – 104

105 – 109

110 – 124

125 – 129

2 Shutter

130 – 144

145 – 149

150 – 164

165 – 169 170 – 184

LED Frequency 12kHz (hold 3s) LED Frequency 25kHz (hold 3s) No function Fan Auto (hold 3s) Fan Silent (hold 3s) Fan Off (hold 3s) Fan High Power (hold 3s) No function Invert Mapping Off (hold 3s) Invert Mapping CW (hold 3s) Invert Mapping CCW (hold 3s) No function LED Mode – Illumination (hold 1,5s) LED Mode – Boost (hold 1,5s) No function
Factory Reset (hold 3s)
User Reset (hold 3s)
No function

0
Reset only starts if Shutter channel is set to DMX 250 Reset only starts if Shutter channel is set to DMX 250 / no selftest by DMX

Remark

Default 0 20
20
59

User Manual

2 Shutter

3 Duration
4 Dimmer 1 5 Red 1 6 Green 1 7 Blue 1

CTC 1 (affects RGB 1)

Tint 1 9 (affects CTC 1
and RGB 1)
Color Macro 1 10 (override RGB 1/
CTC 1)
Color Macro Crossfade 1 11 (Transition Time between Color Macros 1)
12 Dimmer 2 13 Red 2 14 Green 2 15 Blue 2

CTC 2 (affects RGB 2)

185 – 189 190 – 204 205 – 209 210 – 224 225 – 229 230 – 244 245 – 255 000-255 000-255 000-255 000-255 000-255 000 – 004 005-226 182-182 226-226 227-255 0 001-127 128-128 129-255
000 – 005 006-105 106-214 215-244 245-255 000-255 000-255 000-255 000-255 000 – 004 005-226 182-182 226-226 227-255

Shutter open

Strobe 8: random burst pulse (fast slow)

Shutter open

Strobe 9:sine wave (fast slow)

Shutter open

Strobe 10: burst (fast slow)

Shutter open

0 – 100% (0ms – 510ms)

only affects to channel 2 – Strobe 1 025-064

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

5600K

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

according to CTC chart 0

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

no function

Magenta -> Neutral 0
Neutral

Neutral -> Green

Please see ROXX color macro chart

no function

0,1s – 10s (0,1s steps)

11s – 119s (1s steps)

2m – 4m50s (10s steps)

5m – 15m (1m steps)

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

5600K

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

according to CTC chart 0

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

User Manual

Tint 2 (affects CTC 2 and RGB 2)

001-127 128-128

129-255

Color Macro 2 (override RGB 2 / CTC 2)

Color Macro Crossfade 2 19 (Transition Time between Color Macros 2)
20 Dimmer 3 21 Red 3 22 Green 3 23 Blue 3

000 – 005
006-105 106-214 215-244 245-255 000-255 000-255 000-255 000-255 000 – 004

CTC 3 (affects RGB 3)

005-226 182-182 226-226

227-255

Tint 3 25 (affects CTC 3 and
RGB 3)
Color Macro 3 26 (override RGB 3/
CTC 3)
Color Macro Crossfade 3 27 (Transition Time between Color Macros 3)
28 Dimmer 4 29 Red 4 30 Green 4 31 Blue 4

0 001-127 128-128 129-255
000 – 005 006-105 106-214 215-244 245-255 000-255 000-255 000-255 000-255 000 – 004

CTC 4 (affects RGB 4)

005-226 182-182 226-226

227-255

no function Magenta -> Neutral
0 Neutral Neutral -> Green
Please see ROXX color macro chart

no function

0,1s – 10s (0,1s steps)

11s – 119s (1s steps)

2m – 4m50s (10s steps)

5m – 15m (1m steps)

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

5600K

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

according to CTC chart 0

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

no function

Magenta -> Neutral 0
Neutral

Neutral -> Green

Please see ROXX color macro chart

no function

0,1s – 10s (0,1s steps)

11s – 119s (1s steps)

2m – 4m50s (10s steps)

5m – 15m (1m steps)

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

5600K

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

according to CTC chart 0

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

User Manual

Tint 4 33 (affects CTC 4
and RGB 4)
Color Macro 4 34 (override RGB 4 /
CTC 4)

0 001-127 128-128 129-255

Color Macro Crossfade 4 35 (Transition Time between Color Macros 4)

000 – 005 006-105 106-214 215-244 245-255

016-039

040-063

064-87

88-111

Effect override RGB 112-135

36 1-4 / CTC 1-4, Color

Macro 1-4

136-159

160-183

184-207

208-231

232-255

000-51

37 Dimmer Curve

052-101 102-152 153-203 204-255

000-063

38 Dimmer Response

064-127 128-191 192-255

000-84

39 Redshift

085-170

171-255

000-029

030-034

Device Settings

035-039

40 (please see remark 040-044

*1) 045-049

050-054

055-059

no function Magenta -> Neutral
0 Neutral Neutral -> Green

Please see ROXX color macro chart

no function

0,1s – 10s (0,1s steps)

11s – 119s (1s steps)

2m – 4m50s (10s steps)

5m – 15m (1m steps)

Effect 1 (slow to fast)

Effect 2 (slow to fast)

Effect 3 (slow to fast)

Effect 4 (slow to fast)

Effect 5 (slow to fast) 0
Effect 6 (slow to fast)

Effect 7 (slow to fast)

Effect 8 (slow to fast)

Effect 9 (slow to fast)

Effect 10 (slow to fast)

No Function – Current Preset from Menu Settings

Linear Dimmer Curve

Exponential Dimmer Curve

Logarithmic Dimmer Curve

S-Curve Dimmer Curve

No Function – Current Preset from Menu Settings

LED / fast

Medium

Halogen / slow

No Function – Current Preset from Menu

Settings

Redshift affects only

Redshift Off

between CCT 2700- 0 3500K.

Redshift On

No function

Display Backlight On (hold 3s)

Display Backlight Off (hold 3s)

No function

DMX Fail Blackout (hold 3s)

DMX Fail Hold (hold 3s)

DMX Fail – Emergency Light (hold 3s)

User Manual

060-124

125-129

130-134

135-139

140-144

145-149

150-154

155-159

160-164

165-169

170-174

175-179

180-184

185-189

Device Settings

190-194

(please see remark *1)

195-199

200-204

205-209

210-214

215-219

220-224

225-229

230-234

235-239

240-244 245-255

No function

Full Calibration (Colors & CCT / hold 3s)

CCT Calibration (RAW Colors / hold 3s)

No function

LED Frequency 800Hz (hold 3s)

LED Frequency 1200Hz (hold 3s)

LED Frequency 2000Hz (hold 3s)

LED Frequency 3600Hz (hold 3s)

LED Frequency 12kHz (hold 3s)

LED Frequency 25kHz (hold 3s)

No function

Fan Auto (hold 3s)

Fan Silent (hold 3s)

Fan Off (hold 3s)

Fan High Power (hold 3s)

No function

Invert Mapping Off (hold 3s)

Invert Mapping CW (hold 3s)

Invert Mapping CCW (hold 3s)

No function

LED Mode – Illumination (hold 1,5s)

LED Mode – Boost (hold 1,5s)

No function

Factory Reset (hold 3s)

Reset only starts if Shutter channel is set to DMX 250

User Reset (hold 3s)

Reset only starts if Shutter channel is set to DMX 250 / no selftest by DMX

No function

User Manual

57CH EXTENDED RGB (Calibrated)

CH Function

Value

1 Master Dimmer

000-255

2 Master Dimmer Fine 000-255

000 – 019

020 – 024

025 – 064

065 – 069

070 – 084

085 – 089

090 – 104

105 – 109

110 – 124

125 – 129

3 Shutter

130 – 144 145 – 149

150 – 164

165 – 169 170 – 184 185 – 189

190 – 204

205 – 209 210 – 224 225 – 229 230 – 244 245 – 255

4 Duration

000-255

5 Dimmer 1 6 Dimmer 1 Fine 7 Red 1 8 Red Fine 1 9 Green 1 10 Green Fine 1 11 Blue 1 12 Blue Fine 1

000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255

Setting 0 – 100% 0 – 100% Shutter close Shutter open Strobe 1 (fast slow) Shutter open Strobe 2: opening pulse (fast slow) Shutter open Strobe 3: closing pulse (fast slow) Shutter open Strobe 4: random strobe (fast slow) Shutter open Strobe 5: random opening pulse (fast slow) Shutter open Strobe 6:random closing pulse (fast slow) Shutter open Strobe 7: burst pulse (fast slow) Shutter open Strobe 8: random burst pulse (fast slow) Shutter open Strobe 9:sine wave (fast slow) Shutter open Strobe 10: burst (fast slow) Shutter open
0 – 100% (0ms – 510ms)
0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100%

Remark

Default 0 0

only affects to channel 2 – Strobe 1 025-064

255

User Manual

000 – 004

CTC 1 (affects RGB 1)

005-226 182-182 226-226

227-255

Tint 1 14 (affects CTC 1
and RGB 1)
Color Macro 1 15 (override RGB 1/
CTC 1)
Color Macro Crossfade 1 16 (Transition Time between Color Macros 1)
17 Dimmer 2 18 Dimmer 2 Fine 19 Red 2 20 Red Fine 2 21 Green 2 22 Green Fine 2 23 Blue 2 24 Blue Fine 2

0 001-127 128-128 129-255
000 – 005 006-105 106-214 215-244 245-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000 – 004

CTC 2 (affects RGB 2)

005-226 182-182 226-226

227-255

Tint 2 26 (affects CTC 2 and
RGB 2)
Color Macro 2 27 (override RGB 2 /
CTC 2)
Color Macro Crossfade 2 28 (Transition Time between Color Macros 2)

0 001-127 128-128 129-255
000 – 005 006-105 106-214 215-244 245-255

5600K

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

according to CTC chart 0

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

no function

Magenta -> Neutral 0
Neutral

Neutral -> Green

Please see ROXX color macro chart

no function

0,1s – 10s (0,1s steps)

11s – 119s (1s steps)

2m – 4m50s (10s steps)

5m – 15m (1m steps)

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

5600K

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

according to CTC chart 0

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

no function

Magenta -> Neutral 0
Neutral

Neutral -> Green

Please see ROXX color macro chart

no function 0,1s – 10s (0,1s steps) 11s – 119s (1s steps) 2m – 4m50s (10s steps) 5m – 15m (1m steps)

0
65

User Manual

29 Dimmer 3 30 Dimmer 3 Fine 31 Red 3 32 Red Fine 3 33 Green 3 34 Green Fine 3 35 Blue 3 36 Blue Fine 3

CTC 3 (affects RGB 3)

Tint 3 38 (affects CTC 3
and RGB 3)
Color Macro 3 39 (override RGB 3/
CTC 3)
Color Macro Crossfade 3 40 (Transition Time between Color Macros 3)
41 Dimmer 4 42 Dimmer 4 Fine 43 Red 4 44 Red Fine 4 45 Green 4 46 Green Fine 4 47 Blue 4 48 Blue Fine 4

CTC 4 (affects RGB 4)

000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000 – 004
005-226
182-182 226-226
227-255
0 001-127 128-128 129-255
000 – 005 006-105 106-214 215-244 245-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000 – 004
005-226
182-182 226-226
227-255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

5600K

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

according to CTC chart 0

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

no function

Magenta -> Neutral 0
Neutral

Neutral -> Green

Please see ROXX color macro chart

no function

0,1s – 10s (0,1s steps)

11s – 119s (1s steps)

2m – 4m50s (10s steps)

5m – 15m (1m steps)

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

5600K

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

according to CTC chart 0

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

User Manual

Tint 4 50 (affects CTC 4
and RGB 4)

0 001-127 128-128 129-255

Color Macro 4 51 (override RGB 4 /
CTC 4)

Color Macro Crossfade 4 52 (Transition Time between Color Macros 4)

000 – 005 006-105 106-214 215-244 245-255

000-15

016-039

040-063

064-87

88-111 Effect override RGB

53 1-4 / CTC 1-4, Color 112-135

Macro 1-4

136-159

160-183

184-207

208-231

232-255

000-51

54 Dimmer Curve

052-101 102-152 153-203 204-255

000-063

55 Dimmer Response

064-127 128-191 192-255

56 Redshift

000-84 085-170 171-255

no function Magenta -> Neutral
0 Neutral Neutral -> Green

Please see ROXX color macro chart

no function

0,1s – 10s (0,1s steps)

11s – 119s (1s steps)

2m – 4m50s (10s steps)

5m – 15m (1m steps)

No Function

Effect 1 (slow to fast)

Effect 2 (slow to fast)

Effect 3 (slow to fast)

Effect 4 (slow to fast)

Effect 5 (slow to fast)

Effect 6 (slow to fast)

Effect 7 (slow to fast)

Effect 8 (slow to fast)

Effect 9 (slow to fast)

Effect 10 (slow to fast)

No Function – Current Preset from Menu Settings

Linear Dimmer Curve

Exponential Dimmer Curve

Logarithmic Dimmer Curve

S-Curve Dimmer Curve

No Function – Current Preset from Menu Settings

LED / fast

Medium

Halogen / slow

No Function – Current Preset from Menu

Settings

Redshift affects only

Redshift Off

between CCT 2700- 0 3500K.

Redshift On

User Manual

Device Settings 57 (please see
remark *1)

000-029 030-034 035-039 040-044 045-049 050-054 055-059 060-124 125-129 130-134 135-139 140-144 145-149 150-154 155-159 160-164 165-169 170-174 175-179 180-184 185-189 190-194 195-199 200-204 205-209 210-214 215-219 220-224 225-229 230-234
235-239

240-244 245-255

No function

Display Backlight On (hold 3s)

Display Backlight Off (hold 3s)

No function

DMX Fail Blackout (hold 3s)

DMX Fail Hold (hold 3s)

DMX Fail – Emergency Light (hold 3s)

No function

Full Calibration (Colors & CCT / hold 3s)

CCT Calibration (RAW Colors / hold 3s)

No function

LED Frequency 800Hz (hold 3s)

LED Frequency 1200Hz (hold 3s)

LED Frequency 2000Hz (hold 3s)

LED Frequency 3600Hz (hold 3s)

LED Frequency 12kHz (hold 3s)

LED Frequency 25kHz (hold 3s)

No function

Fan Auto (hold 3s)

Fan Silent (hold 3s)

Fan Off (hold 3s)

Fan High Power (hold 3s)

No function

Invert Mapping Off (hold 3s)

Invert Mapping CW (hold 3s)

Invert Mapping CCW (hold 3s)

No function

LED Mode – Illumination (hold 1,5s)

LED Mode – Boost (hold 1,5s)

No function

Factory Reset (hold 3s)

Reset only starts if Shutter channel is set to DMX 250

User Reset (hold 3s)

Reset only starts if Shutter channel is set to DMX 250 / no selftest by DMX

No function

User Manual

20CH DIRECT (RAW) CH Function 1 Red 1 2 Green 1 3 Blue 1 4 Amber 1 5 White 1 6 Red 2 7 Green 2 8 Blue 2 9 Amber 2 10 White 2 11 Red 3 12 Green 3 13 Blue 3 14 Amber 3 15 White 3 16 Red 4 17 Green 4 18 Blue 4 19 Amber 4 20 White 4

Value 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255

12CH DIRECT (RAW) CH Function 1 Master Dimmer
2 Shutter

Value 000-255 000 – 019 020 – 024 025 – 064 065 – 069 070 – 084 085 – 089 090 – 104 105 – 109 110 – 124 125 – 129
130 – 144
145 – 149
150 – 164

Setting 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100%

Remark

Default 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Default 0
20
69

User Manual

165 – 169 170 – 184 185 – 189

2 Shutter
3 Red 4 Green 5 Blue 6 Amber 7 White

190 – 204
205 – 209 210 – 224 225 – 229 230 – 244 245 – 255 000-255 000-255 000-255 000-255 000-255 000 – 004

CTC (affects RGBAW)

005-226 182-182 226-226

227-255

Tint 9 (affects CTC and
RGBAW)

0 001-127 128-128 129-255

Color Macro 10 (override RGBAW/
CTC)

000 – 005

Color Macro Cross- 006-105

fade (Transition Time between Color

106-214

Macros)

215-244

245-255

000-029

030-034

035-039

Device Settings 12 (please see
remark *1)

040-044 045-049 050-054 055-059

060-064

065-069

070-074

Shutter open

Strobe 7: burst pulse (fast slow)

Shutter open

Strobe 8: random burst pulse

(fast slow)

Shutter open

Strobe 9:sine wave (fast slow)

Shutter open

Strobe 10: burst (fast slow)

Shutter open

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

5600K

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

according to CTC chart 0

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

no function

Magenta -> Neutral 0
Neutral

Neutral -> Green

Please see ROXX color macro chart

no function

0,1s – 10s (0,1s steps)

11s – 119s (1s steps)

2m – 4m50s (10s steps)

5m – 15m (1m steps)

No function

Display Backlight On (hold 3s)

Display Backlight Off (hold 3s)

No function

DMX Fail Blackout (hold 3s) 0
DMX Fail Hold (hold 3s)

DMX Fail – Emergency Light (hold 3s)

No function

Linear Dimmer Curve (hold 1,5s)

Exponential Dimmer Curve (hold 1,5s)

User Manual

Device Settings 12 (please see
remark *1)

075-079 080-084 085-089 090-094
095-099
100-104
105-109
110-114
115-119 120-124 125-129 130-134 135-139 140-144 145-149 150-154 155-159 160-164 165-169 170-174 175-179 180-184 185-189 190-194 195-199 200-204 205-209 210-214 215-219 220-224 225-229 230-234
235-239

240-244 245-255

Logarithmic Dimmer Curve (hold 1,5s)

S-Curve Dimmer Curve (hold 1,5s)

No function

LED (Fast) Dimmer Response (hold 1,5s)

Medium Dimmer Response (hold 1,5s)

Halogen (Slow) Dimmer Response (hold 1,5s)

No function

Redshift On (hold 1,5s / affects only between 2700-3500K )

Redshift Off (hold 1,5s)

No function

RAW (hold 3s)

User Calibration (hold 3s)

No function

LED Frequency 800Hz (hold 3s)

LED Frequency 1200Hz (hold 3s)

LED Frequency 2000Hz (hold 3s)

LED Frequency 3600Hz (hold 3s)

LED Frequency 12kHz (hold 3s) 0
LED Frequency 25kHz (hold 3s)

No function

Fan Auto (hold 3s)

Fan Silent (hold 3s)

Fan Off (hold 3s)

Fan High Power (hold 3s)

No function

Invert Mapping Off (hold 3s)

Invert Mapping CW (hold 3s)

Invert Mapping CCW (hold 3s)

No function

LED Mode – Illumination (hold 1,5s)

LED Mode – Boost (hold 1,5s)

No function

Factory Reset (hold 3s)

Reset only starts if Shutter channel is set to DMX 250

User Reset (hold 3s)

Reset only starts if Shutter channel is set to DMX 250 / no selftest by DMX

No function

User Manual

29CH DIRECT (RAW) CH Function 1 Master Dimmer
2 Shutter
3 Dimmer 1 4 Red 1 5 Green 1 6 Blue 1 7 Amber 1 8 White 1 9 Dimmer 2 10 Red 2 11 Green 2 12 Blue 2 13 Amber 2 14 White 2 15 Dimmer 3 16 Red 3 17 Green 3 18 Blue 3

Value 000-255 000 – 019 020 – 024 025 – 064 065 – 069 070 – 084 085 – 089 090 – 104 105 – 109 110 – 124 125 – 129
130 – 144
145 – 149
150 – 164
165 – 169 170 – 184 185 – 189
190 – 204
205 – 209 210 – 224 225 – 229 230 – 244 245 – 255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255

Setting 0 – 100% Shutter close Shutter open Strobe 1 (fast slow) Shutter open Strobe 2: opening pulse (fast slow) Shutter open Strobe 3: closing pulse (fast slow) Shutter open Strobe 4: random strobe (fast slow) Shutter open Strobe 5: random opening pulse (fast slow) Shutter open Strobe 6:random closing pulse (fast slow) Shutter open Strobe 7: burst pulse (fast slow) Shutter open Strobe 8: random burst pulse (fast slow) Shutter open Strobe 9:sine wave (fast slow) Shutter open Strobe 10: burst (fast slow) Shutter open 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100% 0 – 100%

Remark

Default 0
20
255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255
72

User Manual

19 Amber 3 20 White 3 21 Dimmer 4 22 Red 4 23 Green 4 24 Blue 4 25 Amber 4 26 White 4

000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000 – 004

CTC 27 (affects RGBAW
1-4)

005-226 182-182 226-226

227-255

Tint 28 (affects CTC and
RGBAW 1-4)

0 001-127 128-128 129-255

000-029

030-034

035-039

040-044

045-049

050-054

055-059

060-064

065-069

070-074

075-079

Device Settings

080-084

29 (please see remark 085-089

*1) 090-094

095-099

100-104
105-109
110-114
115-119 120-124 125-129 130-134 135-139

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

5600K

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

according to CTC chart 0

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

no function

Magenta -> Neutral 0
Neutral

Neutral -> Green

No function

Display Backlight On (hold 3s)

Display Backlight Off (hold 3s)

No function

DMX Fail Blackout (hold 3s)

DMX Fail Hold (hold 3s)

DMX Fail – Emergency Light (hold 3s)

No function

Linear Dimmer Curve (hold 1,5s)

Exponential Dimmer Curve (hold 1,5s)

Logarithmic Dimmer Curve (hold 1,5s)

S-Curve Dimmer Curve (hold 1,5s)

No function

LED (Fast) Dimmer Response (hold 1,5s)

Medium Dimmer Response (hold 1,5s)

Halogen(Slow) Dimmer Response (hold 1,5s)

No function

Redshift On (hold 1,5s / affects only between 2700-3500K)

Redshift Off (hold 1,5s)

No function

RAW (hold 3s)

User Calibration (hold 3s)

No function

User Manual

140-144

145-149

150-154

155-159

160-164

165-169

170-174

175-179

180-184

185-189

190-194

Device Settings

195-199

29 (please see remark 200-204

*1)

205-209

210-214

215-219

220-224

225-229

230-234

235-239

240-244

245-255

48CH DIRECT (RAW) CH Function 1 Master Dimmer
2 Shutter

Value 000-255 000 – 019 020 – 024 025 – 064 065 – 069 070 – 084 085 – 089 090 – 104 105 – 109 110 – 124 125 – 129
130 – 144
145 – 149

LED Frequency 800Hz (hold 3s) LED Frequency 1200Hz (hold 3s) LED Frequency 2000Hz (hold 3s) LED Frequency 3600Hz (hold 3s) LED Frequency 12kHz (hold 3s) LED Frequency 25kHz (hold 3s) No function Fan Auto (hold 3s) Fan Silent (hold 3s) Fan Off (hold 3s) Fan High Power (hold 3s) No function Invert Mapping Off (hold 3s) Invert Mapping CW (hold 3s) Invert Mapping CCW (hold 3s) No function LED Mode – Illumination (hold 1,5s) LED Mode – Boost (hold 1,5s) No function
Factory Reset (hold 3s)
User Reset (hold 3s)
No function

0
Reset only starts if Shutter channel is set to DMX 250 Reset only starts if Shutter channel is set to DMX 250 / no selftest by DMX

Remark

Default 0
20
74

User Manual

2 Shutter

3 Duration
4 Dimmer 1 5 Red 1 6 Green 1 7 Blue 1 8 Amber 1 9 White 1

CTC 1 (affects RGB 1)

Tint 1 11 (affects CTC 1
and RGB 1)
Color Macro 1 12 (override RGB 1/
CTC 1)
Color Macro Crossfade 1 13 (Transition Time between Color Macros 1)
14 Dimmer 2 15 Red 2 16 Green 2 17 Blue 2 18 Amber 2 19 White 2

150 – 164
165 – 169 170 – 184 185 – 189 190 – 204 205 – 209 210 – 224 225 – 229 230 – 244 245 – 255
000-255
000-255 000-255 000-255 000-255 000-255 000-255 000 – 004
005-226
182-182 226-226
227-255
0 001-127 128-128 129-255
000 – 005 006-105 106-214 215-244 245-255 000-255 000-255 000-255 000-255 000-255 000-255

Strobe 6: random closing pulse (fast slow)

Shutter open

Strobe 7: burst pulse (fast slow)

Shutter open

Strobe 8: random burst pulse (fast slow)

Shutter open

Strobe 9: sine wave (fast slow)

Shutter open

Strobe 10: burst (fast slow)

Shutter open

0 – 100% (0ms – 510ms)

only affects to channel 2 – Strobe 1 025-064

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

5600K

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

according to CTC chart 0

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

no function

Magenta -> Neutral 0
Neutral

Neutral -> Green

Please see ROXX color macro chart

no function

0,1s – 10s (0,1s steps)

11s – 119s (1s steps)

2m – 4m50s (10s steps)

5m – 15m (1m steps)

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

User Manual

CTC 2 (affects RGB 2)

Tint 2 21 (affects CTC 2
and RGB 2)
Color Macro 2 22 (override RGB 2 /
CTC 2)
Color Macro Crossfade 2 23 (Transition Time between Color Macros 2)
24 Dimmer 3 25 Red 3 26 Green 3 27 Blue 3 28 Amber 3 29 White 3

CTC 3 (affects RGB 3)

Tint 3 31 (affects CTC 3
and RGB 3)
Color Macro 3 32 (override RGB 3/
CTC 3)
Color Macro Crossfade 3 33 (Transition Time between Color Macros 3)
34 Dimmer 4 35 Red 4

000 – 004 005-226 182-182 226-226 227-255 0 001-127 128-128 129-255
000 – 005 006-105 106-214 215-244 245-255 000-255 000-255 000-255 000-255 000-255 000-255 000 – 004 005-226 182-182 226-226 227-255 0 001-127 128-128 129-255
000 – 005 006-105 106-214 215-244 245-255 000-255 000-255

5600K

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

according to CTC chart 0

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

no function

Magenta -> Neutral 0
Neutral

Neutral -> Green

Please see ROXX color macro chart

no function

0,1s – 10s (0,1s steps)

11s – 119s (1s steps)

2m – 4m50s (10s steps)

5m – 15m (1m steps)

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

5600K

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

according to CTC chart 0

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

no function

Magenta -> Neutral 0
Neutral

Neutral -> Green

Please see ROXX color macro chart

no function 0,1s – 10s (0,1s steps) 11s – 119s (1s steps) 2m – 4m50s (10s steps) 5m – 15m (1m steps) 0 – 100% 0 – 100%

0
255 255
76

User Manual

36 Green 4 37 Blue 4 38 Amber 4 39 White 4

000-255 000-255 000-255 000-255 000 – 004

CTC 4 (affects RGB 4)

005-226 182-182 226-226

227-255

Tint 4 41 (affects CTC 4
and RGB 4)

0 001-127 128-128 129-255

Color Macro 4 42 (override RGB 4 /
CTC 4)

Color Macro Crossfade 4 43 (Transition Time between Color Macros 4)

000 – 005 006-105 106-214 215-244 245-255

000-15

016-039

040-063

Effect override

064-87

44 RGBAW 1-4 / CTC

1-4, Color Macro 1-4 88-111

112-135

136-159

160-183

Effect override

184-207

44 RGBAW 1-4 / CTC 208-231

1-4, Color Macro 1-4 232-255

000-51

45 Dimmer Curve

052-101 102-152 153-203 204-255

000-063

46 Dimmer Response

064-127 128-191 192-255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

5600K

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

according to CTC chart 0

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

no function

Magenta -> Neutral 0
Neutral

Neutral -> Green

Please see ROXX color macro chart

no function 0,1s – 10s (0,1s steps) 11s – 119s (1s steps) 2m – 4m50s (10s steps) 5m – 15m (1m steps) No Function Effect 1 (slow to fast) Effect 2 (slow to fast) Effect 3 (slow to fast) Effect 4 (slow to fast) Effect 5 (slow to fast) Effect 6 (slow to fast) Effect 7 (slow to fast) Effect 8 (slow to fast) Effect 9 (slow to fast) Effect 10 (slow to fast) No Function – Current Preset from Menu Settings Linear Dimmer Curve Exponential Dimmer Curve Logarithmic Dimmer Curve S-Curve Dimmer Curve No Function – Current Preset from Menu Settings LED / fast Medium Halogen / slow

0
0 0 0 0
77

User Manual

47 Redshift
Device Settings 48 (please see
remark *1)

000-84
085-170 171-255 000-029 030-034 035-039 040-044 045-049 050-054 055-059 060-122 123-127 128-132 133-139 140-144 145-149 150-154 155-159 160-164 165-169 170-174 175-179 180-184 185-189 190-194 195-199 200-204 205-209 210-214 215-219 220-224 225-229 230-234
235-239

240-244 245-255

No Function – Current Preset from Menu

Settings

Redshift affects only

Redshift Off

between CCT 2700- 0 3500K.

Redshift On

No function

Display Backlight On (hold 3s)

Display Backlight Off (hold 3s)

No function

DMX Fail Blackout (hold 3s)

DMX Fail Hold (hold 3s)

DMX Fail – Emergency Light (hold 3s)

No function

RAW (hold 3s)

User Calibration (hold 3s)

No function

LED Frequency 800Hz (hold 3s)

LED Frequency 1200Hz (hold 3s)

LED Frequency 2000Hz (hold 3s)

LED Frequency 3600Hz (hold 3s)

LED Frequency 12kHz (hold 3s)

LED Frequency 25kHz (hold 3s)

No function 0
Fan Auto (hold 3s)

Fan Silent (hold 3s)

Fan Off (hold 3s)

Fan High Power (hold 3s)

No function

Invert Mapping Off (hold 3s)

Invert Mapping CW (hold 3s)

Invert Mapping CCW (hold 3s)

No function

LED Mode – Illumination (hold 1,5s)

LED Mode – Boost (hold 1,5s)

No function

Factory Reset (hold 3s)

Reset only starts if Shutter channel is set to DMX 250

User Reset (hold 3s)

Reset only starts if Shutter channel is set to DMX 250 / no selftest by DMX

No function

User Manual

73CH DIRECT (RAW)

CH Function

Value

1 Master Dimmer

000-255

2 Master Dimmer Fine 000-255

000 – 019

020 – 024

025 – 064

065 – 069

070 – 084

085 – 089

090 – 104

105 – 109

110 – 124

125 – 129

3 Shutter

130 – 144 145 – 149

150 – 164

165 – 169 170 – 184 185 – 189

190 – 204

205 – 209 210 – 224 225 – 229 230 – 244 245 – 255

4 Duration

000-255

5 Dimmer 1 6 Dimmer 1 Fine 7 Red 1 8 Red Fine 1 9 Green 1 10 Green Fine 1 11 Blue 1 12 Blue Fine 1 13 Amber 1 14 Amber Fine 1 15 White 1 16 White Fine 1

000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255

Remark

Default 0 0

only affects to channel 2 – Strobe 1 025-064

255

User Manual

CTC 1 (affects RGB 1)

Tint 1 18 (affects CTC 1
and RGB 1)
Color Macro 1 19 (override RGB 1/
CTC 1)
Color Macro Crossfade 1 20 (Transition Time between Color Macros 1)
21 Dimmer 2 22 Dimmer 2 Fine 23 Red 2 24 Red Fine 2 25 Green 2 26 Green Fine 2 27 Blue 2 28 Blue Fine 2 29 Amber 2 30 Amber Fine 2 31 White 2 32 White Fine 2

CTC 2 (affects RGB 2)

Tint 2 34 (affects CTC 2
and RGB 2)
Color Macro 2 35 (override RGB 2 /
CTC 2)

000 – 004
005-226
182-182 226-226
227-255
0 001-127 128-128 129-255
000 – 005 006-105 106-214 215-244 245-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000 – 004
005-226
182-182 226-226
227-255
0 001-127 128-128 129-255

5600K

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

according to CTC chart 0

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

no function

Magenta -> Neutral 0
Neutral

Neutral -> Green

please use color macros from ROXX color macro chart

no function

0,1s – 10s (0,1s steps)

11s – 119s (1s steps)

2m – 4m50s (10s steps)

5m – 15m (1m steps)

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

5600K

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

according to CTC chart 0

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

no function

Magenta -> Neutral 0
Neutral

Neutral -> Green

Please see ROXX color macro chart

User Manual

Color Macro Crossfade 2 ( 36 Transition Time between Color Macros 2)
37 Dimmer 3 38 Dimmer 3 Fine 39 Red 3 40 Red Fine 3 41 Green 3 42 Green Fine 3 43 Blue 3 44 Blue Fine 3 45 Amber 3 46 Amber Fine 3 47 White 3 48 White Fine 3

CTC 3 (affects RGB 3)

Tint 3 50 (affects CTC 3
and RGB 3)
Color Macro 3 51 (override RGB 3/
CTC 3)
Color Macro Crossfade 3 52 (Transition Time between Color Macros 3)
53 Dimmer 4 54 Dimmer 4 Fine 55 Red 4 56 Red Fine 4 57 Green 4 58 Green Fine 4

000 – 005
006-105 106-214 215-244 245-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000 – 004
005-226
182-182 226-226
227-255
0 001-127 128-128 129-255
000 – 005 006-105 106-214 215-244 245-255 000-255 000-255 000-255 000-255 000-255 000-255

no function

0,1s – 10s (0,1s steps)

11s – 119s (1s steps)

2m – 4m50s (10s steps)

5m – 15m (1m steps)

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

5600K

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

according to CTC chart 0

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

no function

Magenta -> Neutral 0
Neutral

Neutral -> Green

Please see ROXX color macro chart

no function

0,1s – 10s (0,1s steps)

11s – 119s (1s steps)

2m – 4m50s (10s steps)

5m – 15m (1m steps)

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

User Manual

59 Blue 4 60 Blue Fine 4 61 Amber 4 62 Amber Fine 4 63 White 4 64 White Fine 4

000-255 000-255 000-255 000-255 000-255 000-255 000 – 004

CTC 4 (affects RGB 4)

005-226 182-182 226-226

227-255

Tint 4 66 (affects CTC 4
and RGB 4)

0 001-127 128-128 129-255

Color Macro 4 67 (override RGB 4 /
CTC 4)

Color Macro Crossfade 4 68 (Transition Time between Color Macros 4)

000 – 005 006-105 106-214 215-244 245-255

000-15

016-039

040-063

064-87

Effect override

88-111

69 RGBAW 1-4 / CTC 112-135

1-4, Color Macro 1-4 136-159

160-183

184-207

208-231

232-255

000-51

70 Dimmer Curve

052-101 102-152 153-203 204-255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

0 – 100%

255

5600K

2000K-6500K linear in 20-21K steps (please see detailed CTC chart)

5600K

according to CTC chart 0

6500K

6621K-10.000K linear in 120-121K steps (please see detailed CTC chart)

no function

Magenta -> Neutral 0
Neutral

Neutral -> Green

Please see ROXX color macro chart

no function

0,1s – 10s (0,1s steps)

11s – 119s (1s steps)

2m – 4m50s (10s steps)

5m – 15m (1m steps)

No Function

Effect 1 (slow to fast)

Effect 2 (slow to fast)

Effect 3 (slow to fast)

Effect 4 (slow to fast)

Effect 5 (slow to fast)

Effect 6 (slow to fast)

Effect 7 (slow to fast)

Effect 8 (slow to fast)

Effect 9 (slow to fast)

Effect 10 (slow to fast)

No Function – Current Preset from Menu Settings

Linear Dimmer Curve

Exponential Dimmer Curve

Logarithmic Dimmer Curve

S-Curve Dimmer Curve

User Manual

71 Dimmer Response 72 Redshift
Device Settings 73 (please see
remark *1)

000-063
064-127 128-191 192-255
000-84
085-170 171-255 000-029 030-034 035-039 040-044 045-049 050-054 055-059 060-122 123-127 128-132 133-139 140-144 145-149 150-154 155-159 160-164 165-169 170-174 175-179 180-184 185-189 190-194 195-199 200-204 205-209 210-214 215-219 220-224

No Function – Current Preset from Menu Settings

LED / fast

Medium

Halogen / slow

No Function – Current Preset from Menu

Settings

Redshift affects only

Redshift Off

between CCT 2700- 0 3500K.

Redshift On

No function

Display Backlight On (hold 3s)

Display Backlight Off (hold 3s)

No function

DMX Fail Blackout (hold 3s)

DMX Fail Hold (hold 3s)

DMX Fail – Emergency Light (hold 3s)

No function

RAW (hold 3s)

User Calibration (hold 3s)

No function

LED Frequency 800Hz (hold 3s)

LED Frequency 1200Hz (hold 3s)

LED Frequency 2000Hz (hold 3s) 0
LED Frequency 3600Hz (hold 3s)

LED Frequency 12kHz (hold 3s)

LED Frequency 25kHz (hold 3s)

No function

Fan Auto (hold 3s)

Fan Silent (hold 3s)

Fan Off (hold 3s)

Fan High Power (hold 3s)

No function

Invert Mapping Off (hold 3s)

Invert Mapping CW (hold 3s)

Invert Mapping CCW (hold 3s)

No function

LED Mode – Illumination (hold 1,5s)

User Manual

Device Settings 73 (please see
remark *1)
remark *1

225-229

LED Mode – Boost (hold 1,5s)

230-234

No function

235-239 240-244

Factory Reset (hold 3s) User Reset (hold 3s)

Reset only starts if

Shutter channel is set

to DMX 250

Reset only starts if

Shutter channel is set

to DMX 250 / no self-

test by DMX

245-255

No function

After adjustments please set the value back to 000 to avoid any disturbance by endless function call.

User DMMXaCnHuaAlRT

Color Macro Chart for DMX

Gels – Color Macros for DMX

DMX value Gel Name

000-005 no function

006-008 Red

009-011 Fire

012-014

Medium Red

015-017

Primary Red

018-020 Med Amber

021-023

Dark Amber

024-026 Deep Amber

027-029

Orange

030-032 Deep Golden Amber

033-035 Yellow

036-038 Green

039-041 Lime Green

042-044 Moss Green

045-047 LEE Green

048-050 Primary Green

051-053 Jas Green

054-056 Jade

057-059 Blue

060-062 Sky Blue

063-065 Tokyo Blue

066-068 Light Blue

069-071 Marine Blue

072-074

Med Blue

075-077 Congo Blue

078-080 Mikkel Blue

081-083 Rose Pink

084-086 Med Pink

087-089 Light Lavender

090-092 Lavender

Color Number
100% Red LED LEE 019 LEE 027 LEE 106 LEE 020 LEE 022 LEE 104 LEE 105 LEE 135 LEE 101 100% Green LED LEE 088 LEE 089 LEE 121 LEE 139 LEE 738 LEE 323 100% Blue LED LEE 068 LEE 071 LEE 118 LEE 131 LEE 132 LEE 181 LEE 716 LEE 002 LEE 036 LEE 052 LEE 058

Gels – Color Macros for DMX

093-095 Magenta

096-098 Mauve

099-101

Smokey Pink

102-104

Special Med Lavender

105-107

Ultimate Violet

108-110

Magical Magenta

111-113

Chrysalis Pink

114-116

Specia KH Lavender

117-119

Bulb White

120-122

Halogen White

123-125

Neutral White

126-128

Daylight White

129-131

Cold White I

132-134

Cold White II

135-137

White (only if available)

LEE 113 LEE 126 LEE 127 LEE 343 LEE 707 LEE 795 LEE 798 LEE 799 2700K 3200K 4200K 5600K 6000K 6300K
100% White LED

138-140

Amber (only if available) 100% Amber LED

141-143

Lime (only if available)

100% Lime LED

144-146 147-149 150-152 153-155 156-158 159-161 162-164 165-209
210-255

Cyan (only if available)
User Color 1 User Color 2 User Color 3 User Color 4 User Color 5 Color Jumping stop Color Jumping speed slow fast Color fading speed slow fast

100% Cyan LED
color 1-37 color 1-37

User Manual

Color Macro Chart for Stand Alone

Gels – Color Macros for Standalone Mode

Position Gel Name

Color Number

Red

100% Red LED

Fire

LEE 019

Medium Red

LEE 027

Primary Red

LEE 106

Med Amber

LEE 020

Dark Amber

LEE 022

Deep Amber

LEE 104

Orange

LEE 105

Deep Golden Amber

LEE 135

Yellow

LEE 101

Green

100% Green LED

Lime Green

LEE 088

Moss Green

LEE 089

LEE Green

LEE 121

Primary Green

LEE 139

Jas Green

LEE 738

Jade

LEE 323

Blue

100% Blue LED

Sky Blue

LEE 068

Tokyo Blue

LEE 071

Light Blue

LEE 118

Marine Blue

LEE 131

Med Blue

LEE 132

Congo Blue

LEE 181

Mikkel Blue

LEE 716

Rose Pink

LEE 002

Med Pink

LEE 036

Light Lavender

LEE 052

Gels – Color Macros for Standalone Mode

Position Gel Name

Color Number

Lavender

LEE 058

Magenta

LEE 113

Mauve

LEE 126

Smokey Pink

LEE 127

Special Med Lavender

LEE 343

Ultimate Violet

LEE 707

Magical Magenta

LEE 795

Chrysalis Pink

LEE 798

Specia KH Lavender

LEE 799

Bulb White

2700K

Halogen White

3200K

Neutral White

4200K

Daylight White

5600K

Cold White I

6000K

Cold White II

6300K

Amber (only if available) 100% Amber LED

Lime (only if available)

100% Lime LED

Cyan (only if available)

100% Cyan LED

User Manual
CTC channel DMX / Color temperature
10.000 9.500 9.000 8.500 8.000 7.500 7.000 6.500 6.000 5.500 5.000 4.500 4.000 3.500 3.000 2.500 2.000

Color temperature (°K)

100

105

110

DMX (step)

115

120

125

130

135

140

145

150

155

160

165

170

175

180

185

190

195

200

205

210

215

220

225

230

235

240

245

250

255

User Manual

CCT-Chart

DMX (Step)
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

Color Temp (°K) 5600 5600 5600 5600 5600 2000 2020 2041 2061 2081 2102 2122 2143 2163 2183 2204 2224 2244 2265 2285 2305 2326 2346 2367 2387 2407 2428 2448 2468 2489 2509 2529 2550 2570 2590 2611 2631 2652 2672 2692 2713 2733 2753

DMX (Step)
43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85

Color Temp (°K) 2774 2794 2814 2835 2855 2876 2896 2916 2937 2957 2977 2998 3018 3038 3059 3079 3100 3120 3140 3161 3181 3201 3222 3242 3262 3283 3303 3324 3344 3364 3385 3405 3425 3446 3466 3486 3507 3527 3548 3568 3588 3609 3629

DMX (Step)
86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128

Color Temp (°K) 3649 3670 3690 3710 3731 3751 3771 3792 3812 3833 3853 3873 3894 3914 3934 3955 3975 3995 4016 4036 4057 4077 4097 4118 4138 4158 4179 4199 4219 4240 4260 4281 4301 4301 4342 4362 4382 4403 4423 4443 4464 4484 4505

DMX (Step)
129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171

Color Temp (°K) 4525 4545 4566 4586 4606 4627 4647 4667 4688 4708 4729 4749 4769 4790 4810 4830 4851 4871 4891 4912 4932 4952 4973 4993 5014 5034 5054 5075 5095 5115 5136 5156 5176 5197 5217 5238 5258 5278 5299 5319 5339 5360 5380

DMX (Step)
172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214

Color Temp (°K) 5400 5421 5441 5462 5482 5502 5523 5543 5563 5584 5604 5624 5645 5665 5686 5706 5726 5747 5767 5787 5808 5828 5848 5869 5889 5910 5930 5950 5971 5991 6011 6032 6052 6072 6093 6113 6133 6154 6174 6195 6215 6235 6256

DMX (Step)
215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255

Color Temp (°K) 6276 6296 6317 6337 6357 6378 6398 6419 6439 6459 6480 6500 6621 6741 6862 6983 7103 7224 7345 7466 7586 7707 7828 7948 8069 8190 8310 8431 8552 8672 8793 8914 9034 9155 9276 9397 9517 9638 9759 9879 10000

User Manual

7.5 RDM Templates* The ROXX Show series features support for various RDM functions. RDM (Remote Device Management) is a protocol enhancement to USITT DMX512 that allows bi-directional communication between the fixtures and the controller over a standard DMX line. This protocol will allow configuration, status monitoring and management. You will need a RDM controller to get control over the supported parameters. See the tables below for supported RDM features.

Label: Model: Manufacturer: ID: Device ID:

ROXX CLUSTER B4 FC CLUSTER B4 FC ROXX 6A6Ah 203 xxxx

*Note: During RDM identifying process CLUSTER B4 FC flashes white to blue color alternately.

RDM functions For easy identifying ROXX CLUSTER B4 FC during RDM process the unit will jump from white color to blue color every second.

PID 0x00F0 0x00E0 0x00E1
0x8001
0x8002 0x8003 0x8050 0x0500 0x8051 0x8052
0x8053
0x8060 0x8054 0x8055 0x8056 0x8057 0x8061 0x8058 0x8020 0x8021 0x8022 0x8023 0x8024 0x8025

Function DMX Start Adress DMX Personality DMX Slots

Action Set Set Read

Effect

Set

Effect Dimmer

Set

Effect Speed

Set

Master / Slave

Set

Display Flip

Set

Display Backlight

Set

Display Lock

Set

Startup Mode

Set

Color Settings

Set

DMX Fail

Set

Dimmer Curve

Set

Dimmer Response

Set

Redshift

Set

Color Calibration

Set

RAW Balance

Set

User Calibration- Red 1

Set

User Calibration- Green 1 Set

User Calibration- Blue 1

Set

User Calibration- Amber 1 Set

User Calibration- White 1 Set

User Calibration- Red 2

Set

Values 001-512 17x DMX modes n.a. 0= Stop Program / 1= Effect 1 / 2= Effect 2 / 3= Effect 3 / 4= Effect 4 / 5= Effect 5 / 6= Effect 6 / 7= Effect 7 / 8= Effect 8 / 9= Effect 9 / 10= Effect 10
0= Master / 1= Slave 0= Off / 1= On 0= Off / 1= On 0= Off / 1= On 0= DMX / 1= AUTO / 2= Color Macro / 3= Quick Color / 4= Tunable White / 5=User Color 0= Color Calibration / 1= RAW 1= Hold / 2= Blackout / 3= Emergency 1= Linear / 2= Exponential / 3= Logarithmic / 4= S-Curve 1= LED / 2= Medium / 3= Halogen 0= Off / 1= On 0=CCT Calibration / 1= Full Calibration 0= RAW / 1= User Calibration

User Manual

0x8026 0x8027 0x8028 0x8029 0x802A 0x802B 0x802C 0x802D 0x802E 0x802F 0x8030 0x8031 0x8032 0x8033
0x8059
0x805A 0x805B 0x805C 0x805E 0x805F 0x00C0 0x8700 0x0400 0x8701 0x8702 0x8703 0x8704 0x8705 0x8706 0x8707 0x8708

User Calibration- Green 2 Set

User Calibration- Blue 2

Set

User Calibration- Amber 2 Set

User Calibration- White 2 Set

User Calibration- Red 3

Set

User Calibration- Green 3 Set

User Calibration- Blue 3

Set

User Calibration- Amber 3 Set

User Calibration- White 3 Set

User Calibration- Red 4

Set

User Calibration- Green 4 Set

User Calibration- Blue 4

Set

User Calibration- Amber 4 Set

User Calibration- White 4 Set

LED Frequency (PWM)

Set

Fan Invert Mapping LED Mode Factory Reset User Reset Firmware Version Serial Number Device Power on Time Temperature LED 1 Temperature LED 2 Temperature LED 3 Temperature LED 4 LED 1 on Time LED 2 on Time LED 3 on Time LED 4 on Time

Set Set Set Yes/No Yes/No read Read Read Read Read Read Read Read Read Read Read

1= 800Hz / 2= 1200Hz / 3= 2000Hz / 4= 3600Hz / 5= 12kHz / 6= 25kHz 0= Auto / 1= Silent / 2= Fan Off / 3= Max. Power 0= Off / 1= CW / 2= CCW 0= Illumination / 1= Boost 0= No / 1= Yes 0= No / 1= Yes n.a. n.a. n.a. n.a. n.a. n.a. n.a. n.a. n.a. n.a. n.a.

User Manual

Sensors RDM enables various readouts for remote device monitoring. See the table below for sensors and sensor types. Please note: The RDM controller communicates with the fixtures to show only the available sensors for this fixture. The table is subject to change without notice.

Name Temperature Software Version Errors

xx°C / xxx°F SW-Version

8. TROUBLESHOOTING
Did you try turning the device off and on again?

Problem Device is not responding.
Device has turned off. Device has stopped responding. Device operates strangely.

Reason
No power.
Fuse defect. Power failure or power was turned off. DMX cable correct? DMX cable inverted (pins correct?) DMX cable terminated? Stand Alone program running?

Solution
Check cable connections and conform that power is switched on.
Contact your qualified service technician / manufacturer.
Check power supply, fuse, connections, switches.
Check cables. Use a phase inverter or different cables. If not, install DMX termination at the end of the cable. Stop internal Stand Alone.

User Manual
9. MANUFACTURER´S DECLARATION
Manufacturer´s Warranty & Limitations of Liability Please find our warranty conditions and limitations of liability inside our manufacturer´s declaration at www.roxxlight.com/support
Requesting Warranty-Service To request warranty service for your product, please contact: ROXX GmbH, Hansestr. 91 51149 Köln Email: info@roxxlight.com or the ROXX authorized reseller in your country, from where you purchased your product.
Correct Disposal of this product
This is for the European Union and European countries with electrical waste collection systems. When this label is shown on the product or brochure it means that the item cannot be disposed with household waste. In order to prevent damage to the environment or human health please do not dispose this product uncontrolled. Make sure to act responsible, recycle this product separately from other types of waste to enable lasting reuse of resources. Private users please contact the retailer where you purchased this product or your local authorities to find out where and how proper recycling of this item is possible. Business users please contact your supplier or check the terms and conditions of your purchasing contract. Make sure not to mix this product with other commercial waste.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help.
92

User Manual
CE Compliance
The equipment marketed by ROXX GmbH complies (where applicable) with the essential requirements and other specifications of the following Directives: · 2014/30/EU (EMC) · 2014/35/EU (LVD) · 2011/65/EU (RoHS)
The complete EU- and UK-Declaration of Conformity can be found at www.roxxlight.com/support, or you can also request it at info@roxxlight.com

ROXX GmbH | Hansestr. 91 | 51149 Köln | www.roxxlight.com Tel: +49 (0) 2203 20371-0 | Fax: +49 (0) 2203 20371-20

REV: 01

Documents / Resources

ROXX CLUSTER B4 FC LED Lights [pdf] User Manual
B4-FC, CLUSTER B4 FC LED Lights, CLUSTER B4 FC, LED Lights, Lights

References

User Manual

ROXX CLUSTER B4 FC LED Lights

Specifications

Physical Installation and Rigging

Connections

Startup

Control Display

Troubleshooting

Frequently Asked Questions

Documents / Resources

References

Leave a comment

Cancel reply