Contents hide
1 Roth FG-600 QuickStop Sensor
2 Specifications
3 FAQs
4 PRODUCT INFORMATION
5 INSTALLATION AND USING INSTRUCTION
6 App setup
7 Accessories
8 CONTACT INFORMATION
9 Documents / Resources
9.1 References

Roth-LOGO

Roth FG-600 QuickStop Sensor

Roth-FG-600-QuickStop-Sensor-PRODUCT

Specifications

  • Product Name: Roth QuickStop Sensor 2
  • Model: FG-600:3
  • Installation Date: 01.11.2023

FAQs

  • Q: Can the QuickStop Sensor 2 be installed by individuals or only by authorized companies?
    • A: Installation of the QuickStop Sensor 2 should be done by authorized companies to ensure proper setup and compliance with safety standards.
  • Q: How do I reset the alarm on the QuickStop Sensor 2?
    • A: To reset the alarm, briefly turn off the unit or hold it for 2 blinks.

PRODUCT INFORMATION

  • Roth QuickStop Sensor 2 is a system that can protect against damage caused by leaks on water installations. The system‘s main advantage is evident when used with invisible or difficult to install installation parts.
  • Functionally, – if the sensor cable or the wireless sensor comes into contact with water between the two conductors, the motor valve closes within 5 seconds and the control unit starts to alarm. If the system is connected to the app, a notification will be sent.
  • The valve remains closed and the control unit continues to alarm until you manually acknowledge the alarm on the control unit or app.
  • If the sensors have become wet in connection with floor washing or the like, the alarm can be set aside for 12 hours, with the expectation that the sensor or sensor cable has become dry.
  • The wireless sensor can either be placed directly on the floor so that it detects by the cable leads or you can mount a sensor cable in the sensor so that it can cover a larger area. The sensor can also be mounted in the included wall bracket, which is attached to the wall and the sensor cable is run down to the floor. The wireless sensor has a range of approx. 30 m, depending on the location. Up to 20 sensors can be connected to a control unit.
  • The valve is made of stainless steel 316 and can be mounted in domestic water installations according to the water meter.
  • The control unit can handle up to two 230V QuickStop actuatores and two sensor cables as well as 20 wireless sensors. It comes with 1 pcs as well as a 230V QuickStop actuator included in the package.
  • The 230V plug can be used for any purpose up to 10A, e.g. electric water heaters.
  • The sensor cable is self-adhesive and should be mounted on dry, smooth and non-dusty surfaces.
  • The sensor cable is delivered in a roll of 4 m and can be cut with scissors in the desired length.
  • To prevent the valve from getting stuck, there is a built-in valve exercise program in the control unit that briefly closes the valve once a week.
  • The closing takes place automatically after 7 days +12 hours.
  • If the interruption occurs at an inconvenient time, you can briefly disconnect power to the controller 12 hours before the time you want the program to run.

Example:

  1. Device is plugged in on monday 10 am
  2. First program sequence start – monday 10 pm
  3. Subsequently starts – every monday 10 pm

INSTALLATION AND USING INSTRUCTION

  • If you want to connect a sensor cable directly to the control unit, do so before connecting it to 230V. Before use the control unit needs to have a sensor cable connected. To do that, open the cover, by pushing it down (down towards the two connectors) and and turn it up 90 degrees.Roth-FG-600-QuickStop-Sensor-FIG- (1)
  • Pull the white protective foil off the sensor cable approx. 20 mm, so that the adhesive surface is free. The side of the sensor cable that does not have the copper conductors. If you are in doubt, you can feel with a fingernail if there are two elevations on the cable, these are the copper conductors.
  • Press sensor tape firmly into the cover, and pull approx. 20 mm of the yellow protective film of the sensor cable so that the contact surface of the cable becomes free.Roth-FG-600-QuickStop-Sensor-FIG- (2)
  • Press the cover down against the clamps and push it into place so it is locked.Roth-FG-600-QuickStop-Sensor-FIG- (3)
  • The QuickStop ball valve must be mounted on the domestic water installation after the water meter.
  • If the QuickStop only needs to secure one tap, it can be mounted on the inlet of the tap.
  • Remember that work on domestic water may only be carried out by authorized companies.Roth-FG-600-QuickStop-Sensor-FIG- (4)
  • Insert the actuator plug into the socket at the bottom. It does not matter if you use one or the other connector if you only use one actuator.
  • REMEMBER to screw the plug tight with the delivered screw.Roth-FG-600-QuickStop-Sensor-FIG- (5)
  • If only one actuator is used, the empty plug must be mounted in the free plug and screwed on.
  • Remove the white protective film and unwind the sensor cable at the place you want protection against water.Roth-FG-600-QuickStop-Sensor-FIG- (6)
  • Remove the yellow protective film from the sensor cable.
  • Use of the QuickStop Sensor 2 – Plug in the control unit in a 230V socket.Roth-FG-600-QuickStop-Sensor-FIG- (7)
  • During startup, the controller detects how many sensor cables are connected in the first three seconds, when it blinks twice.
  • After three seconds, it will flash once or twice, depending on how many sensor cables are installed. If one or more sensor cables are mounted directly to the control unit, but the control unit remains on and flashes green after start-up, the sensor cable is not mounted correctly. Check the installation if necessary. turn the sensor cable 180 degrees so that the opposite side is facing up. The side with the copper conductors must face upwards.
  • After the start-up sequence, the controller goes into normal mode and lights up green. If no sensor cables are connected to the control unit, it will stand and flash green until the first wireless sensor is registered. The installation of the sensor cable can be easily checked by placing a damp finger on the sensor cable, if the sensor cable is installed correctly, the control unit will sound an alarm and shut off the water. The alarm can be reset most easily by cutting off the power to the unit for 5 seconds. alternatively, you can hold “√” for 2 blinks to mute the alarm, then hold “Roth-FG-600-QuickStop-Sensor-FIG- (9)” for 2 blinks to open the valve.
  • If you want to connect a sensor cable at a later stage, the power to the control unit must be disconnected.Roth-FG-600-QuickStop-Sensor-FIG- (8)

Normal mode:

  • Control unit light green
  • Valve is open
  • 230V socket is turn onRoth-FG-600-QuickStop-Sensor-FIG- (10)

Light indications on the control unit:

  • Everything OK – Green
  • Wireless sensor registration – Blinks dark blue
  • Signal strength below 10% to sensor – Flashes red/purple
  • Registration for WiFi – Blinks light blue
  • Error while registering wireless sensor or WiFi – Flashing tube/blue
  • Alarm – Red
  • Alarm mute – Flashing red
  • No sensor cable detected – Flashing green (only by startup)
  • Discounted sensor cable – Flasing 4 times red, small break, and then flasing 4 times red
  • Battery alarm – Flashing purple
  • Low temperature alarm – Flashing yellow
  • Frost protection is deactivated – Flashes yellow/greenRoth-FG-600-QuickStop-Sensor-FIG- (11)

Add new wireless sensor

  • A. Insert the batteries into the wireless sensor.
  • B. Hold down the “√” button on the control unit for 5 blinks to start signing up. The registration mode is active for 60 sec. and the logo flashes blue.
  • C. Press and hold the button on the wireless sensor for 1 blinks then the LED on the sensor flashes.
  • D. When the sensor is registered to the control unit, the logo on the control unit starts to glow green.
  • E. If timeout (after 60 sec.), the logo on the control unit flashes red /blue until the user presses the “√” button on the control unit.
    • If more wireless sensors are needed, repeat the process above. 20 wireless sensors can be connected to a control unit.
    • If you want to have extra range between the wireless sensors or there are difficult send/receive conditions, a Touchline® SL repeater can be inserted between the sensors and the control unit.Roth-FG-600-QuickStop-Sensor-FIG- (12) Roth-FG-600-QuickStop-Sensor-FIG- (13) Roth-FG-600-QuickStop-Sensor-FIG- (14)

Installation of sensor cable in sensor

  • To mount a sensor cable, open the cover by sliding it down and pushing it up to 90 degrees.
  • Pull the white protective foil off the sensor cable approx. 20 mm. so that the adhesive surface is free. Press the sensor cable into the cover.
  • Pull approx. 20 mm of the yellow protective film of the sensor cable so that the contact surface of the cable becomes free.
  • Press the cover down against the clamps and slide it into place so that it is locked.
  • Please note that if the sensor cable is not correctly fitted in the sensor, this may result in a leak not being registered! The installation of the sensor cable can be easily checked by placing a damp finger on the sensor cable, if the sensor cable is installed correctly, the control unit will sound an alarm and shut off the water. The alarm is reset by briefly turning off the power to the control unit, or holding “√” down for 5 blinks and then hold down ”Roth-FG-600-QuickStop-Sensor-FIG- (9)” for 5 blinks. to open the valve.Roth-FG-600-QuickStop-Sensor-FIG- (15)

Mounting of sensor in wall bracket

  • The wireless sensor can be mounted on the wall in the included wall bracket.
  • If you choose to mount the sensor on the wall, you must first mount a sensor cable that can be pulled down to the floor in the area that you want to monitor.

230V adapter for sensor

  • It is possible to connect a 230V adapter to a wireless sensor if you do not want to be dependent on having to change batteries in between.
  • Use adapter No. AMA5ER4-050100Y.
  • Remove the rubber stopper at the top of the sensor and connect the adapter to the sensor.
  • Connect the adapter to 230V.

Roth-FG-600-QuickStop-Sensor-FIG- (16)

Remove a wireless sensor

  • A. Hold down the “√” button on the control unit for 5 blinks to begin deleting the sensor.Roth-FG-600-QuickStop-Sensor-FIG- (17)
    • The delete mode is active for 60 sec. and the logo flashes blue.
  • B. Press for 10 blinks or press the button on the wireless sensor 10 times.Roth-FG-600-QuickStop-Sensor-FIG- (19)
  • C. If the sensor is correctly erased, the logo on the control unit lights up blue for 10 sec. and then changes to green.
  • D. If timeout (after 60 sec.), the logo on the control unit flashes red/blue until the user clicks the “√” button on the control unit. If more sensors need to be removed, repeat the process above.Roth-FG-600-QuickStop-Sensor-FIG- (18)

Link test for wireless sensor – Check if a sensor is registered to the control unit

  • a. Press the button on the sensor 2 blinks
  • b. If the sensor is paired with the controller, the logo on the controller flashes blue.

Alarms

  • Leakage register
    • Water is detected on either a fixed sensor or a wireless sensor.
    • Investigate why there is water on the sensor before you possibly interrupts the alarm.
    • Indicator – The logo on the control unit lights red – The control unit sounds.
    • Solution – Mute the alarm, either directly on the control unit by holding down “√” for 2 blinks or via the app. If you want to open the water, do so by holding down “Roth-FG-600-QuickStop-Sensor-FIG- (9)” for 2 blinks.
    • By muting the alarm, the QuickStop is deactivated, ie it no longer monitors the system for the next 12 hours, which can lead to water damage.

Sensor cable is unplugged on control unit

  • One or more sensor cables are unplugged and can no longer detect leaks.
  • Examine why the sensor cable is no longer properly mounted in the socket.
  • Indicator – The logo on the control unit flashes red 4 times, pauses and flashes 4 times, etc. The control unit sounds.
  • Solution – Remove the control unit from the power supply and install the sensor cable correctly, according to.

Wireless sensor has lost connection to the control unit

  • One or more wireless sensors have not been connected to the control unit for 24 hours and can no longer detect leaks.
  • Investigate why the wireless sensor is no longer connected to the control unit, if necessary. using “link test”.
  • Indicator – The logo on the control unit flashes red 4 times, pauses and flashes 4 times, etc. The control unit sounds.
  • Solution – Check the connection with “link test”, see page 10.
  • Replace the batteries and do the “link test” again.
  • Examine whether the transmission conditions are limited by e.g. iron between the sensor and the control unit, possibly. move the sensor to another location.
  • If it is not possible to connect from the desired location, you may need one repeater.

Low battery on a wireless sensor

  • A wireless sensor sends information to the control unit that the battery is low at a level below 10%.
  • Indicator – The logo on the control unit flashes purple.
  • The control unit beeps every 20 seconds.
  • Solution – Replace the batteries.
  • It is possible to mute the alarm, for 12 hours, by pressing the “√” button on the control unit 2 blinks.

Low temperature warning (below 5 degrees)

Roth-FG-600-QuickStop-Sensor-FIG- (21) Roth-FG-600-QuickStop-Sensor-FIG- (22) Roth-FG-600-QuickStop-Sensor-FIG- (23)

  • If a sensor detects a temperature below 5 degrees, it sends a frost risk alarm.
    • A. The logo on the control unit flashes yellow – The valve closes.
    • B. The control unit sounds/ alarms/ tick button.
  • It is possible to deactivate the frost protection of the system by holding the “√” down for 20 blinks. The freeze function is manually disabled until you manually enable the function again by holding down the “√” for 20 blinks.
  • When the frost protection is switched off, the display will flash yellow/ green.

Manual opening/closing of the valve

  • If you want to operate the valve manually, it is possible.
    • A. Pull up the small adjustable pinhead (approx. 5 mm)
    • B. Turn clockwise to close the valve – turn counterclockwise to open
  • REMEMBER to push the impeller down again after manual operation, as otherwise the valve will not be able to shut off the water afterwards and there is a risk of water damage.

App setup

Roth-FG-600-QuickStop-Sensor-FIG- (24)

  • QuickStop Sensor 2 can be monitored via the app, where the water can also be opened and closed. If you connect your control to the app, you will also receive notifications if there are alarms on the system.
  • Multiple systems can be connected on the same app.
  • There can be multiple users on the same app. This is done by the first user sharing his phone and sending the password to the new user.
  • Note that the phone’s WiFi must be switched on and set to 2.4 GHz in order to connect to the control unit.
  • During the setup of the app, you have to press the “ ” button and hold it down until the logo has flashed white 5 times, when you release the logo starts to flash light blue. When the controller is connected to the app, it will check for firmware updates. When the connection between the app and the controller is complete, the logo will start to glow light blue. After approx. 10 sec. the controller returns to normal mode and lights up solid green in the logo.
  • If an error occurs during the setup for the app, e.g. if the password is incorrect or you are not on the 2.4 GHz connection, the logo will flash light blue/red.
  • To avoid signal interference between the control unit and the wireless sensors, the WiFi router should be placed at least 3 meters from both the control unit and the sensors.

Update firmware on QuickStop Sensor 2

  • If the control unit is connected to the app and WiFi, you can update the firmware on the control unit.
  • If there is a new firmware, it will appear on Roth’s website.
    • A. Hold down “Roth-FG-600-QuickStop-Sensor-FIG- (9)” for 10 blinks.
    • B. After 10 sec. the logo quickly starts flashing white
    • C. If a newer version of the firmware is on the portal, the logo flashes 2 x blue and the controller starts downloading the new firmware.
    • D. The controller will reboot several times while updating the firmware.
    • E. After completing the firmware update, the logo will flash white/green, after which the control unit reboots and returns to normal operation (logo lights up green).
  • If an error occurs during the update or the controller is not online, the logo will flash red/light blue.
  • In the event of an error in the update, the power to the control unit must be briefly interrupted so that the control unit reboots, then you can try to carry out an update again according to the above procedure.Roth-FG-600-QuickStop-Sensor-FIG- (25)

Accessories

Accessories til Roth QuickStop Sensor 2

  • Wireless sensor HVAC No. 7TE1000005
  • 4 m sensor cable HVAC No. 7TE1000006
  • ½” actuator HVAC No. 7TO1000000
  • ¾” actuator HVAC No. 7TO1000001
  • 230V adapter HVAC No. 7TE1000007
  • Roth Touchline® SL repeater HVAC No. 466397.400
  • Roth plate floor sensor for QSS2 HVAC No. 7TE1000015Roth-FG-600-QuickStop-Sensor-FIG- (26)

Tear off this page and place it on the control unit

  • Light indications on the control unit:
    • Everything OK – Green
    • Wireless sensor registration – Blinks dark blue
    • Signal strength below 10% to sensor – Flashes red/purple
    • Registration for WiFi – Blinks light blue
    • Error while registering wireless sensor or WiFi – Flashing red/blue
    • Alarm – Red
    • Alarm mute – Flashing red
    • No sensor cable detected – Flashing green (only by startup)
    • Discounted sensor cable – Flasing 4 times red, small break, and then flasing 4 times red
    • Battery alarm – Flashing purple
    • Low temperature alarm – Flashing yellow
    • Frost protection is deactivated – Flashes yellow/green
  • Operation of the control unit
    • Mute alarms – Hold down the “√” for 2 blinks.
    • Open/close the valve manually – Hold down “Roth-FG-600-QuickStop-Sensor-FIG- (9)” for 2 blinks.
    • Registration of wireless sensor – Hold down the “√” for 5 blinks.
    • Setup for WiFi – Hold down “Roth-FG-600-QuickStop-Sensor-FIG- (9)” for 5 blinks.
    • Deactivate/activate frost protection – Hold down the “√” for 20 blinks.
    • Firmware update – Hold down “Roth-FG-600-QuickStop-Sensor-FIG- (9)” for 10 blinks.
    • Restore factory settings – Hold “Roth-FG-600-QuickStop-Sensor-FIG- (9)” for 15 blinks.
  • Restoring factory settings
    • It is possible to reset a controller to factory settings by holding down “Roth-FG-600-QuickStop-Sensor-FIG- (9)” for 15 blinks.

CONTACT INFORMATION

Documents / Resources

Roth FG-600 QuickStop Sensor [pdf] Instruction Manual
FG-600 3, FG-600 QuickStop Sensor, FG-600, QuickStop Sensor, Sensor

References

Leave a comment

Your email address will not be published. Required fields are marked *