ROADSAFE Isuzu D-Max Series Recovery Points
Product Information
| Product | Product Code | Note |
|---|---|---|
| Recovery Point | RPCOL02V2 | Do not tighten bolts until fitting is complete. WLL: 5000kg |
Product Usage Instructions
- For ease of fitting, we recommend following these steps:
- Read the fitting instructions in their entirety.
- Elevate the vehicle and support it on axle stands.
- Remove both front wheels.
- Remove the front plastic lip.
- Remove the front section of the factory skid plate and loosen the bolts of the adjacent skid plate.
- Partially remove the plastic inner guard.
- Loosen the factory tie-down support, loosen 3 bolts at the rear, and remove 2 bolts at the front.
To begin installation, identify the following parts:
| Driver Side | Passenger Side |
|---|---|
|
|
Follow these steps for installation:
- Install the M12 x 100mm bolt, the recovery point, and the required shim to the chassis. Only tighten enough to support the recovery point plate and shim.
- Install the M16 bolt, M16 X 4mm shim washer, and captive nut. Do not completely tighten both bolts to allow for alignment of the other bolts to be installed.
- Install the 2x M10 bolts and spacers as shown in the picture. To make installation easier, install the bolt towards the front bumper and then the rear bolt. Note: Strip packer 4mm or 8mm thick may not be needed with some bull bars.
- Install the M12 X 60mm bolt with dimpled washer in the factory tie-down point.
- Tighten the 2x M10 bolts to position the recovery bracket, then tighten the M12 x 100mm bolts on both sides to their rated torque. There is no access to these bolts once the bash plate is reattached.
Overview
- VEHICLE Holden Colorado RG (2012 – 2017) & Isuzu Dmax (2012 – 2020)
- PRODUCT Recovery Point
- PRODUCT CODE RPCO L02V2
- NOTE Do not tighten bolts until fitting is complete. WLL: 5000kg
DURING RECOVERY ALWAYS USE BOTH RECOVERY POINTS
For ease of fitting, we recommend:
- Read the fitting instructions in their entirety
- Elevate the vehicle and support on axle stands
- Remove both front wheels
- Remove front plastic lip
- Remove front section of factory skid plate & loosen the bolts of the adjacent skid plate
- Partially remove the plastic inner guard
- Loosen factory tie down support, loosen 3 bolts at rear, remove 2 bolts at the front
Parts
To begin installation, identify the following parts:
| DRIVER SIDE | PASSENGER SIDE | |||
| Recovery Bracket | 1 | Recovery Bracket | 1 | |
| L Shaped Packer 8mm | 1 | L Shaped Packer 8mm | 1 | |
| L Shaped Packer 4mm | 1 | L Shaped Packer 4mm | 1 | |
| Strip Packer 4mm | 1 | Strip Packer 4mm | 1 | |
| Strip Packer 6mm | 1 | Strip Packer 6mm | 1 | |
| 13mm Thick Spacer | 1 | 13mm Thick Spacer | 1 | |
| 18mm Thick Spacer | 1 | 18mm Thick Spacer | 1 | |
| Turned Wwasher | 1 | Turned Washer | 1 | |
| Bullbar Panel Angle Mount | 1 | Bullbar Panel Angle Mount | 1 | |
| M8 X 25mm Long | 1 | M8 X 25mm Long | 1 | |
| M10 X 1.25 X 50mm Long | 2 | M10 X 1.25 X 50mm Long | 2 | |
| M12 X 60mm Long | 1 | M12 X 60mm Long | 1 | |
| M12 X 100mm Long | 1 | M12 X 100mm Long | 1 | |
| M16 X 60mm Long | 1 | M16 X 60mm Long | 1 | |
| M10 Spring Washer | 2 | M10 Spring Washer | 2 | |
| M10 Washer 30 X 3mm | 2 | M10 Washer 30 X 3mm | 2 | |
| M12 Washer 30 X 3mm | 6 | M12 Washer 30 X 3mm | 6 | |
| M16 Washer 32 X 2mm | 1 | M16 Washer 32 X 2mm | 1 | |
| M16 Washer 32 X 4mm | 1 | M16 Washer 32 X 4mm | 1 | |
| M12 Nyloc Nut | 2 | M12 Nyloc Nut | 2 | |
| M16 Nyloc Nut | 1 | M16 Nyloc Nut | 1 | |
| M8 Spring Washer | 1 | M8 Spring Washer | 1 | |
| M8 Flat Washer | 1 | M8 Flat Washer | 1 | |
| M8 Nyloc Nut | 1 | M8 Nyloc Nut | 1 |
- VEHICLE Holden Colorado RG (2012 – 2017) & Isuzu Dmax (2012 – 2020)
- PRODUCT Recovery Point
- PRODUCT CODE RPCO L02V2
- NOTE Do not tighten bolts until fitting is complete. WLL: 5000kg
Installation
DURING RECOVERY ALWAYS USE BOTH RECOVERY POINTS
Installation Key Points:
- Do not tighten bolts until fitting is complete.
- Due to differences in factory bumpers, nudge bars, and bull bars. Selecting correct shim and bolt configuration is the fitter’s responsibility.
- Install the M12 x 100mm bolt, the recovery point and required shim to the chassis. Only tighten enough to support recovery point plate and shim.
- Install M16 bolt, M16 X 4mm shim washer and captive nut. Do not completely tighten both bolts to allow for alignment of the other bolts to be installed.
- Install the 2x M10 bolts and spacers as shown in the below picture. To make installation easier; install the bolt towards front bumper and then rear bolt.
- Install the M12 X 60mm bolt with dimpled washer in the factory tie-down point.
- Tighten the 2x M10 bolts to position the recovery bracket, then tighten the M12 x 100mm bolts on both sides to their rated torque. There is no access to these bolts once bash plate is reattached.
- Loosen the 2x M10 bolts to allow fitment of the bash plate.
- Fit bash plate and tighten all bolts to their specified torque.
Re-Installation
- Reconnect the plastic inner guard.
- Reattach plastic front lip.
- Replace both front wheels.
- Lower the vehicle.
- Tighten all wheel nuts on both front wheels to manufactures specification.
A division of Specialist Wholesalers Pty. Ltd. ABN 64 163 280 279
VIC PH: 03 8687 1700 | QLD PH: 07 3737 7420 | Email: sales@roadsafe.com.au
Documents / Resources
 |
ROADSAFE Isuzu D-Max Series Recovery Points [pdf] Instruction Manual Isuzu D-Max Series Recovery Points, Isuzu D-Max Series, Recovery Points, Points |
