Manual de utilizare a termostatului cu afișaj LCD MC701, controler de temperatură pentru încălzire

1. Produs terminatview

The SINOTIMER MC701 is a versatile digital PID temperature controller designed for precise heating and cooling applications. It features an LCD display, supports various input types including PT100 and K-type thermocouples, and provides SSR/Relay output with alarm functions. This manual provides essential information for the safe and effective operation of your MC701 controller.

Figura 1.1: Față view of the MC701 controller showing the PV and SV displays, and control buttons.

Figura 1.2: Înclinat view of the MC701 controller, highlighting the model number (MC701-611) and default input type (K).

2. Caracteristici cheie

• High-precision digital PID temperature control.
• Dual LCD display for Process Value (PV) and Set Value (SV).
• Supports multiple input types: K-type thermocouple, PT100 RTD.
• SSR (Solid State Relay) and Relay output options.
• Configurable heating and cooling control modes.
• Integrated alarm functions (ALM1, ALM2).
• Temperature unit selection: Celsius (°C) or Fahrenheit (°F).

3. Informații de siguranță

Vă rugăm să citiți și să înțelegeți toate instrucțiunile de siguranță înainte de instalare și utilizare. Nerespectarea acestor instrucțiuni poate duce la electrocutare, incendiu sau vătămări corporale grave.

• Asigurați-vă că sursa de alimentare voltage matches the controller's specifications (100-240V AC).
• Toate cablările trebuie efectuate de un electrician calificat.
• Disconnect power before making any wiring connections or performing maintenance.
• Do not operate the controller in environments with excessive moisture, dust, or corrosive gases.
• Asigurați o ventilație adecvată pentru a preveni supraîncălzirea.
• This device is not intended for life-support systems or applications where malfunction could lead to severe injury or property damage.

4. Configurare și instalare

Proper installation is crucial for the accurate and reliable operation of the MC701 controller.

4.1 Montare

The MC701 is designed for panel mounting. Ensure adequate space for ventilation and wiring connections.

Figure 4.1: MC701 controller shown with its included mounting clips for panel installation.

4.2 Conexiuni de cablare

Refer to the wiring diagram on the side of the unit and the instructions below for correct connections. Use appropriate gauge wires for all connections.

Figure 4.2: Detailed wiring diagram on the side of the MC701 unit, showing connections for power, sensor input, SSR, and relay outputs.

• Power Supply (85-265VAC): Connect to terminals 8 and 9.
• SSR Output (OUT): Connect to terminals 10 (+) and 11 (-).
• Relay Output (RELAY): Connect to terminals 13 (NO - Normally Open) and 14 (NC - Normally Closed). Terminal 12 is the common (COM).
• RTD Input (PT100): Connect to terminals 4 (A), 5 (B), and 6 (B).
• Thermocouple Input (TC): Connect to terminals 5 (+) and 6 (-).
• Alarm Outputs (AL1, AL2): Connect to terminals 1, 2, and 3.

5. Instrucțiuni de utilizare

5.1 Afișare pesteview

The MC701 features a dual display:

• PV (Process Value): Displays the current measured temperature.
• SV (Set Value): Displays the desired target temperature.

Indicatoare luminoase:

• OUT: Indicates output status (heating/cooling).
• AT: Auto-tuning indicator.
• ALM1, ALM2: Alarm indicators.

5.2 Funcțiile butoanelor

• SET: Enters parameter setting mode or confirms a setting.
• < (R/S): Shifts cursor during setting, or resets alarm.
• V (Down Arrow): Decreases value during setting.
• ^ (Up Arrow): Increases value during setting.

5.3 Setarea temperaturii țintă (SV)

1. Apăsați tasta SET Apăsați butonul o dată. Afișajul SV va începe să clipească.
2. Utilizați ^ şi V butoane pentru a regla temperatura dorită.
3. Utilizați < pentru a deplasa cursorul și a realiza o ajustare mai rapidă.
4. Presa SET again to confirm the new SV and exit the setting mode.

5.4 Setări avansate ale parametrilor

To access advanced parameters (e.g., PID parameters, alarm settings, input type, temperature unit), press and hold the SET button for several seconds until the first parameter code appears on the PV display.

• Utilizare ^ şi V to navigate through parameters.
• Presa SET la view or edit a parameter's value.
• Ajustați valoarea utilizând ^, V, și <.
• Presa SET to save the value and return to the parameter list.
• To exit advanced settings, press and hold SET again, or wait for a timeout.

6. Întreținere

Regular maintenance ensures the longevity and optimal performance of your MC701 controller.

• Cleaning: Wipe the display and casinȘtergeți cu o cârpă moale și uscată. Nu utilizați substanțe de curățare abrazive sau solvenți.
• Ventilation: Ensure the ventilation slots on the sides of the unit are not obstructed to prevent overheating.
• Connections: Periodically check all wiring connections for tightness and signs of wear or corrosion.
• Storage: If storing the unit, keep it in a dry, dust-free environment within its specified operating temperature range.

7. Depanare

8. Specificații

Figura 8.1: lateral view of the MC701 controller displaying its detailed specification label.

9. Garanție și asistență

For technical support or warranty inquiries, please contact SINOTIMER customer service through the retailer or the official SINOTIMER website. Please have your product model number (MC701) and purchase details ready.

This product is manufactured by SINOTIMER.