Offgridtec MPPT Pro Duo Charge Controller 30A 12V/24V Instruction Manual

1. Introducere

Thank you for choosing the Offgridtec MPPT Pro Duo charge controller. This device is designed to efficiently manage solar power input to charge two independent battery banks, typically a main service battery and a starter battery, in 12V or 24V systems. It utilizes Maximum Power Point Tracking (MPPT) technology to optimize energy harvest from your solar panels. Please read this manual thoroughly before installation and operation to ensure safe and optimal performance.

Figura 1: Față view of the Offgridtec MPPT Pro Duo Charge Controller.

2. Instrucțiuni de siguranță

Always observe the following safety precautions to prevent personal injury or damage to the controller and connected equipment:

• Instalarea trebuie efectuată numai de personal calificat.
• Ensure all power sources (solar panels, batteries) are disconnected before installation or maintenance.
• Folosiți unelte adecvate și purtați echipament de protecție.
• Do not disassemble or attempt to repair the controller. Contact Offgridtec support for assistance.
• Asigurați o ventilație adecvată în jurul controlerului pentru a preveni supraîncălzirea.
• Connect batteries with correct polarity. Reverse polarity can cause severe damage.
• Use fuses or circuit breakers on all battery and solar panel connections as recommended by local regulations and system design.
• Avoid short-circuiting battery terminals or solar panel wires.
• Keep the controller away from flammable materials, moisture, and direct sunlight.

3. Produs terminatview

3.1 Caracteristici cheie

• Dual battery charging: Charges both main (service) and starter batteries.
• MPPT Technology: Maximizes power harvest from solar panels.
• Supports 12V and 24V systems.
• Maximum charge current up to 30A.
• Adaptive three-level charging for extended battery life.
• Supports various battery types: Gel, Flooded, LiFePO4, Li-NiCoMn (for main battery).
• Secondary charge output for starter battery (supports lead-acid).
• Optional remote display and Bluetooth compatibility (accessories required).
• AES control signal for car refrigerators to prevent energy waste.
• Standard bus protocol and RS485 communication connection.
• Robust aluminum heatsink design for efficient cooling.
• Overload, reverse polarity, and deep discharge protection.

3.2 Componente

The Offgridtec MPPT Pro Duo charge controller includes:

• MPPT Pro Duo Charge Controller unit.
• Borne de conectare.
• Integrated LED status indicators.
• SET button for battery type selection.
• Temperature sensor ports (one with integrated sensor, one for external).
• Port de comunicație RS485.
• AES signal output port.

Figura 2: Față și spate view of the charge controller, highlighting the heatsink design.

4. Configurare și instalare

Proper installation is crucial for the safe and efficient operation of your charge controller. Ensure all safety instructions are followed.

4.1 Locul de montare

• Montați controlerul vertical pe o suprafață neinflamabilă.
• Ensure adequate air circulation around the heatsink for optimal cooling.
• Avoid locations exposed to direct sunlight, high temperatures, or moisture.
• Dimensions: 24.7 cm (L) x 16.5 cm (W) x 6.9 cm (H).
• Mounting holes diameter: 5 mm.

Figure 3: Physical dimensions of the MPPT Pro Duo charge controller, showing the aluminum heatsink.

4.2 Schema de cablare și conexiuni

Follow the wiring sequence below. Incorrect wiring can damage the controller or batteries.

1. Connect Battery 1 (Main/Service Battery): Connect the positive and negative terminals of your main battery to the BATT1 terminals on the controller. Use appropriate cable gauge (e.g., 16 mm² / AWG6). Ensure correct polarity.
2. Connect Battery 2 (Starter Battery): Connect the positive and negative terminals of your starter battery to the BATT2 terminals on the controller. Use appropriate cable gauge (e.g., 4 mm² / AWG12). Ensure correct polarity.
3. Connect Solar Panels (PV): Connect the positive and negative terminals of your solar panel array to the PV terminals on the controller. Ensure the open-circuit voltage of your solar array does not exceed 100V.
4. Connect Temperature Sensors: The controller includes ports for temperature sensors. Connect the provided sensor to monitor battery temperature for optimized charging.
5. Conexiuni opționale:
   • Comunicare RS485: For connecting an optional remote display or USB adapter for PC communication.
   • AES Signal Output: For controlling car refrigerators to prevent excessive discharge of the main battery.
6. Împământare: Ensure the controller is properly grounded (negative grounding).

Figure 4: Simplified wiring diagram showing connections from solar panel to controller and dual batteries.

Figura 5: Example installation of the charge controller in a recreational vehicle.

5. Instrucțiuni de utilizare

5.1 Pornirea inițială

After all connections are securely made, connect the battery power first, then the solar panel power. The controller will perform a self-test, and the LED indicators will illuminate.

5.2 Setting Battery Type (BATT1)

The controller supports various battery types for the main battery (BATT1). To select the correct battery type:

1. Țineți apăsat butonul SET button for approximately 5 seconds until the battery type indicator starts flashing.
2. Apăsați tasta SET button repeatedly to cycle through the available battery types (Gel, Flooded, LiFePO4, Li-NiCoMn).
3. Once the desired battery type is selected, wait for 5 seconds without pressing any button. The indicator will stop flashing, and the setting will be saved.

The secondary battery (BATT2) is typically charged as a lead-acid battery and does not require specific type selection.

5.3 Indicatori LED

The front panel features LED indicators to show the operational status:

• PV Status LED: Indicates solar panel input status.
• BATT1 Status LEDs: Show the charging stage and state of charge for the main battery.
• BATT2 Status LED: Indicates charging status for the starter battery.
• LED de eroare: Illuminates to indicate a fault or warning. Refer to the troubleshooting section.

Figure 6: Installed charge controller showing illuminated LED indicators.

5.4 Procesul de încărcare

The MPPT Pro Duo uses an adaptive three-level charging algorithm to optimize battery health and lifespan. It prioritizes charging the main battery (BATT1) and then provides a maintenance charge to the starter battery (BATT2).

• Încărcare în vrac: Oferă curent maxim pentru încărcarea rapidă a bateriei.
• Taxa de absorbtie: Menține un volum constanttage pentru a încărca complet bateria fără a o supraîncărca.
• Taxă plutitoare: Reduce volumultagla un nivel mai scăzut pentru a menține bateria la încărcare completă și a compensa autodescărcarea.

6. Întreținere

Regular maintenance ensures the longevity and optimal performance of your charge controller:

• Inspecție vizuală: Periodically check for loose connections, damaged wiring, or signs of corrosion.
• curatenie: Keep the controller clean and free of dust. Use a dry cloth to wipe the exterior. Do not use liquids or solvents.
• Ventilare: Asigurați-vă că aripioarele radiatorului nu sunt obstrucționate pentru a permite disiparea corectă a căldurii.
• Verificarea conexiunii: Verify that all terminal connections are tight and secure.
• Sănătatea bateriei: Monitor the health of your batteries. A failing battery can affect the performance of the entire system.

7. Depanare

If you encounter issues with your MPPT Pro Duo, refer to the following common problems and solutions:

If the problem persists after attempting these solutions, please contact Offgridtec customer support.

8. Specificații

9. Garanție și asistență

For warranty information, please refer to the terms and conditions provided at the time of purchase or contact Offgridtec GmbH directly. Keep your proof of purchase for any warranty claims.

For technical support, troubleshooting assistance beyond this manual, or inquiries about accessories, please contact Offgridtec customer service. Contact details can typically be found on the manufacturer's official website-ul sau documentația achiziției dumneavoastră.

10. Aplicații tipice

The Offgridtec MPPT Pro Duo charge controller is suitable for a variety of off-grid and mobile solar power systems, including:

• Vehicule recreaționale (RV-uri) și Campervane
• Marine Systems (Boats & Yachts)
• Remote Telecommunication Stations
• Off-grid Cabins and Small Homes
• Camping and Outdoor Solar Setups

Figura 7: Examples of typical applications for the MPPT Pro Duo charge controller.