1. Produs terminatview
The RAB Lighting LFP16A Sleek Floodlight is designed for outdoor illumination, providing efficient and durable lighting. This fixture accommodates a PAR16 type bulb and features a robust die-cast aluminum housing with a powder-coated finish for enhanced durability and weather resistance.
Caracteristici cheie:
- Designed for 60W PAR16 bulbs, delivering 650 lumens output (bulb not included).
- Durable die-cast aluminum housing with a powder-coated finish.
- Gasket and O-ring seals provide resistance against weather elements.
- Integrated shield helps reduce glare.
- Equipped with a 1/2" NPS threaded arm for secure mounting and a locking swivel for adjustable positioning.

Figure 1: RAB Lighting LFP16A Sleek Floodlight. This image shows the floodlight fixture with its threaded arm and wiring, highlighting its compact and durable design.
2. Informații de siguranță
Vă rugăm să citiți și să înțelegeți toate instrucțiunile înainte de a instala sau utiliza acest produs. Nerespectarea acestor instrucțiuni poate duce la electrocutare, incendiu sau alte pericole care ar putea provoca daune materiale sau vătămări corporale.
- Siguranta electrica: Always disconnect power at the circuit breaker or fuse box before wiring or servicing the fixture.
- Electrician calificat: Instalarea trebuie efectuată de către un electrician calificat, în conformitate cu toate codurile electrice locale și naționale.
- Împământare: Asigurați-vă că dispozitivul de iluminat este împământat corespunzător pentru a evita potențialele pericole electrice.
- Tip bec: Use only PAR16 type bulbs with a maximum wattage de 60W. Depășirea puterii maximetage poate provoca supraîncălzirea și deteriorarea corpului de iluminat.
- Locație umedă: This fixture is suitable for wet locations. Ensure all connections are properly sealed and waterproofed during installation.
- Temperatură: Do not install near combustible materials or surfaces that may be affected by heat.
3. Conținutul pachetului
Verificați dacă toate componentele sunt prezente înainte de a începe instalarea:
- RAB Lighting LFP16A Sleek Floodlight Fixture (1)
- Manual de instrucțiuni (1)
Note: Light bulb and wire connectors are not included and must be purchased separately.
4. Configurare și instalare
This floodlight is designed for wall mounting and features a 1/2" NPS threaded arm for secure attachment to a junction box or mounting accessory. Follow these steps for proper installation:
- Pregătiți pentru instalare:
- Opriți alimentarea cu energie de la întrerupătorul de circuit înainte de a începe orice lucrare electrică.
- Gather necessary tools: screwdriver, wire strippers, electrical tape, silicone sealant (for waterproofing).
- Montați dispozitivul:
- Thread the 1/2" NPS arm of the floodlight into a compatible outdoor junction box or mounting plate. Ensure a tight and secure connection.
- Use the locking swivel to adjust the initial angle of the fixture.

Figure 2: Detail of the 1/2" NPS threaded arm and 180-degree adjustable swivel. This illustrates the mounting mechanism and flexibility of the floodlight.
- Conexiuni cablare:
- Connect the black wire from the fixture to the hot (black) wire from the power supply.
- Connect the white wire from the fixture to the neutral (white) wire from the power supply.
- Connect the bare copper or green wire from the fixture to the ground wire from the power supply.
- Secure all connections with appropriate wire connectors and electrical tape. For outdoor installations, consider using silicone-filled wire nuts for added moisture protection.
- Instalați becul:
- Carefully insert a PAR16 bulb (max 60W) into the fixture socket. Do not overtighten.
- Seal and Test:
- Ensure all connections are secure and the fixture is properly sealed against moisture. Apply silicone sealant around the mounting base if necessary.
- Restore power at the circuit breaker and test the floodlight's operation.
5. Instrucțiuni de utilizare
Once installed and powered, the RAB Lighting LFP16A Floodlight operates by the control of the circuit it is connected to (e.g., a wall switch, timer, or photocell). There are no direct controls on the fixture itself.
- Reglarea direcției luminii: The fixture features a locking swivel arm. To adjust the light direction, loosen the locking nut on the swivel, position the floodlight as desired, and then tighten the locking nut securely.
- Reducerea strălucirii: The built-in shield is designed to minimize glare, directing light effectively to the intended area.

Figura 3: Example of the LFP16A floodlight used in a landscape setting, demonstrating its illumination capabilities.
6. Întreținere
Întreținerea regulată asigură performanța optimă și longevitatea reflectorului dumneavoastră.
- curatenie: Curățați periodic exteriorul corpului de iluminat cu o lavetă moale șiamp lavetă. Nu folosiți substanțe de curățare abrazive sau solvenți, deoarece acestea pot deteriora finisajul. Asigurați-vă că este oprită alimentarea cu energie electrică înainte de curățare.
- Înlocuire bec:
- Opriți alimentarea cu energie a corpului de iluminat la întrerupătorul de circuit.
- Lăsați becul vechi să se răcească complet înainte de a-l manipula.
- Carefully unscrew and remove the old PAR16 bulb.
- Insert a new PAR16 bulb (max 60W) into the socket, ensuring it is seated correctly.
- Restore power and test the new bulb.
- Inspecţie: Annually inspect the fixture for any signs of wear, damage, or loose connections. Address any issues promptly.
7. Depanare
| Problemă | Cauza posibila | Soluţie |
|---|---|---|
| Lumina nu se aprinde. | Nicio putere la corp. Bec defect. Conexiunea cablajului slab. | Verificați întrerupătorul. Înlocuiți becul. Inspect and secure wiring (ensure power is off). |
| Lumina pâlpâie. | Bec slăbit. Tip de bec incompatibil. Alimentare cu energie electrică fluctuantă. | Strângeți becul. Ensure correct PAR16 bulb is used. Consult an electrician if power supply is unstable. |
| Apă în interiorul corpului de iluminat. | Etanșare necorespunzătoare în timpul instalării. Damaged gasket/O-ring. | Turn off power, disassemble, dry, re-seal all connections and mounting points with silicone sealant. Contact RAB Lighting for replacement parts if necessary. |
8. Specificații
| Atribut | Detaliu |
|---|---|
| Numărul de model | LFP16A |
| Producător | Iluminat RAB |
| Sursa de alimentare | Electric cu fir |
| Voltage | 120 volți |
| Wattage (Max) | 60 wați |
| Tip bec | PAR16 (HPS, LED compatible) |
| Material | Die-cast Aluminum (Housing), Plastic (Internal components) |
| Termina | Powder-coated (Bronze color) |
| Tip de montare | Wall (1/2" NPS threaded arm) |
| Greutatea articolului | 10.4 uncii |
| Diametrul asamblat | 2-7/16 inci |
| Componente incluse | Corp de iluminat |
| Bateriile necesare | Nu |
9. Garanție și asistență
The RAB Lighting LFP16A Sleek Floodlight comes with a Garanție de 1 an de la producător de la data achiziției. Această garanție acoperă defectele de materiale și de fabricație în condiții normale de utilizare.
For warranty claims, technical support, or further assistance, please contact RAB Lighting customer service. Refer to the official RAB Lighting website pentru cele mai recente informații de contact.
Producător: Iluminat RAB
Website: www.rablighting.com (Examplinkul, linkul real poate varia)





