HJSR79 Remote Control Key Diagram
“
Product Information
Specifications:
- Remote Control Functions: Full lock, Half lock, Underbed light
control, Bluetooth switch, Volume adjustment, Vibration intensity
adjustment, Music control - Underbed Light: Seven-color light with cycle feature and
automatic turn-off after 5 minutes - Bluetooth Function: Allows connection to Bluetooth device for
music playback - Volume Adjustment: 15 levels available
- Vibration Intensity Adjustment: 4 levels (0-3)
Product Usage Instructions
Full Lock and Half Lock Functions:
– To activate Full Lock function: Press any key for about 5
seconds until the backlight flashes and the buzzer rings three
times. This locks all remote control functions. Repeat the same
process to unlock.
– To activate Half Lock function: Press the lock key and pause
(1+7) simultaneously for about 5 seconds. The remote control enters
semi-lock state, only locking the function of the music oscillator.
Repeat the process to unlock.
Underbed Light Control:
– Press keys 1-7 to change the color of the underbed light. Long
press for 5 seconds to turn off the underbed light. The default
automatic turn-off time is 5 minutes.
Bluetooth Switch:
– Press the Bluetooth button to turn on Bluetooth function.
Follow audio prompts for connection to a Bluetooth device. Press
again to turn off Bluetooth function.
Volume Adjustment:
– During music follow-up mode, use the volume increase and
decrease buttons to adjust speaker volume. There are 15 levels
available.
Vibration Intensity Adjustment:
– In music follow-up mode, use the follow-up enhancement button
to increase vibration intensity in cycles (0-1-2-3).
Music Control:
– Use the music pause/play button to pause or resume music
playback. Use the track switch button to navigate between
tracks.
FAQ
Q: How do I reset the remote control if it’s not functioning
properly?
A: To reset the remote control, align the code and perform a
power-on reset by following the fixed positions mentioned in the
manual.
“`
Remote control key diagram
Fixed position (red reserved)
Power-on reset mm Fixed
position
Alignment YES
line
ZG
SNORE
Head
34
22
Foot
126
0
Align the code and reset
LOUNGE
TV
85
123
60
100
1
Remote control function description
Key label
Feature
Full lock function: press for about 5 seconds, the backlight flashes, the
buzzer rings three times, all functions of the entire remote control are
locked, power off and power on to keep the state before power off (APP
function is unavailable); Press and hold again for about 5 seconds, the
backlight blinks, and the buzzer rings three times. After unlocking, all
functions are available
Half lock function: Press the lock + pause (1+7) at the same time for about
1
5 seconds, the backlight flashes, and the buzzer sounds twice. The remote
control enters the semi-lock state, and only locks the function of the
music oscillator (3 to 9 keys); Press and hold again for about 5 seconds,
the backlight flashes, and the buzzer sounds twice to unlock the function
After the full lock buzzer rings three times, press any key (except the
lock key), the buzzer rings three times to remind: the half lock buzzer
rings two times, press the music key part, the buzzer rings two times to
remind
Underbed light – seven-color light, press 1-7 times, one color at a time,
2
cycle, long press 5S backlight flicker, turn off the underbed light,
default 5min automatic turn off
Bluetooth switch: When the device is powered on and Bluetooth is off, the Bluetooth device cannot be searched, and the button in the music followup operation area does not respond
Press this button, the Bluetooth function will be turned on, and the
audio prompt “Bluetooth on, please wait” will be turned on, and the
Bluetooth device (ZYKJ_XXXXX) will be found and connected. After the
3
connection is successful, the audio prompt “bluetooth connected” will be
displayed, and music will be played. When the vibrator is powered on for
the first time, the music is followed by the default 2 intensity (if the
vibration intensity has been manually adjusted before opening, it will
vibrate according to the adjusted intensity)
Press the button again, the Bluetooth function is turned off, and the sound prompts “Bluetooth off”.
2
4
5
6
7 8 9 10 11 12 13 14 15 16
17
18
In the music follow-up mode, press this button to increase the speaker volume, a total of 15 gears, keep 15 gears after the highest level, the sound prompt “Maximum volume” vibration intensity is not affected (no change for the time being, now 10 gears).
In the music follow-up mode, press this button to reduce the speaker Volume. After setting the tone to the lowest setting, the sound prompts “Min Volume”, and the vibration intensity is not affected
Follow-up enhancement: In the music follow-up mode, press this button to increase the vibration intensity of the follow-up, and cycle according to 0-1-2-3 gear (enter the music follow-up mode, default 2 gear) (audio real-time broadcast status :massager off/massager low /massager medium/massager high)
Music Pause/Play: In music follow mode, press this button to pause or continue playing music
In music follow up mode, press this button to switch up the track
In music follow up mode, press this button to switch down the track
Back up (motor out), release to stop The motor runs to the M position with one key (no initial value). Multiplexing function: FLAT+M, backlight flashing, buzzer ringing, record the current motor position to M (power off does not clear) Leg up (motor out), release to stop Back down (motor retracted), release to stop One-button reset, all motors retracted to the minimum stroke position, power-on reset Leg down (motor retracted), release to stop The motor runs to the ZG position (with initial value) with one click. Multiplexing function: FLAT+ZG, backlight flashing, buzzer ringing, record current motor position to ZG (power off clear) The motor runs to the SNORE position (with initial value) with one click. Multiplexing function: FLAT+SNORE, backlight flashing, buzzer ringing, record the current motor position to SNORE (power off to clear) Reuse function key: Before pressing the key, if the massager is in working state, all the massagers will be turned off after pressing the key, and the working time of the massage motor for the next time will be set 10min,
3
20min,30min respectively. The timing time is displayed through two
indicators. If the massager is not in working state, the working time of
the massage motor is directly fixed for the next time
(Status audio broadcast: massager off)
Head massager enhancement: Press the button, if the head massager does not start,
start the head massager and enter “CONSTANT” mode; If the head massage motor is started, increase the vibrational intensity of the massager,1 23 off, cycle switch 19 (default 30 minutes off) Intensity 1,10 minutes light red, intensity 2, 20 minutes light
green, intensity 3, two lights together bright blue. (Intensity status audio broadcast:
massager off/massager low /massager medium/massager high)
Mode switching –CONSTANT-PULSE-WAVE
Massage motor mode adjustment, after the massager has been started, press
this button, the working massage motor will enter the “PULSE” mode, press
the button again, the massage motor will enter the “WAVE” mode, press the
button again, the massage motor will enter the “CONSTANT” mode, and then 20
cycle. The CONSTANT buzzer will sound once, the PULSE buzzer will sound
twice, the WAVE buzzer will sound three times, and the current intensity
color will also be displayed (audio real-time broadcast status: massager
off, Massager OFF, massager mode one/ massager mode two/massager mode
three) Massager mode one/ Massager mode two/ Massager mode three)
Mode switching –CONSTANT-PULSE-WAVE
Massage motor mode adjustment, after the massager has been started, press
this button, the working massage motor will enter the “PULSE” mode, press
the button again, the massage motor will enter the “WAVE” mode, press the
button again, the massage motor will enter the “CONSTANT” mode, and then 21
cycle. The CONSTANT buzzer will sound once, the PULSE buzzer will sound
twice, the WAVE buzzer will sound three times, and the current intensity
color will also be displayed (audio real-time broadcast status: massager
off, Massager OFF, massager mode one/ massager mode two/massager mode
three) Massager mode one/ Massager mode two/ Massager mode three)
*** Pay attention ***
During the motor operation, the music vibrates in the follow-up and vibration mode, the
vibration is weakened, the third gear is reduced to the second gear (the second gear
and the first gear are unchanged), and the motor stops and then resumes the third gear
(the volume does not drop).
Coding method:
[Remote control head rise + foot rise + control box code key] Buzzer sounds, indicatingsuccessful code
* The control box has a reset function for the code key (the remote control enters the
sleep state and is disconnected from the control box)
* The control box is powered on and reset, all motors are reset at the same time, and
the reset process cannot be interrupted by any key
4
Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: –Reorient or relocate the receiving antenna. –Increase the separation between the equipment and receiver. –Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. –Consult the dealer or an experienced radio/TV technician for help.
5
Documents / Resources
 |
Richmat HJSR79 Remote Control Key Diagram [pdf] User Guide HJ8258, 2AJJGHJ8258, HJSR79 Remote Control Key Diagram, HJSR79, Remote Control Key Diagram, Control Key Diagram, Diagram |