rf solutions 433MHz ZETAPLUS Smart Transceiver Module Instruction Manual

To set up receive mode, use the command ATR followed by the
packet size. For example, to receive “HELLOWORLD,” send the
command: ATR#010. Make sure to set the channel if required before
the packet size.

Transmitter:

Once receiver parameters are set, send the data packet from the
transmitter using the command ATS#002#010HELLOWORLD. The receiver
will output the data through the TX pin to the host’s RX pin.

Advanced Operation:

To reduce current consumption, use the ATM command. For example,
to set the receiver to standard RX mode, send the command: ATM#001.
Refer to the product datasheet for a full command set and technical
information.

FAQ:

Q: How can I wake the ZETAPLUS module from a shutdown
state?

A: Connect the shutdown pin to GND to wake the module.

Q: What is the command to set the ZETAPLUS into low power sleep
mode?

A: To place the module into low power sleep mode, use the
command: ATM#003. Note that the receiver will not receive in this
mode.

“`

View Fullscreen

ZETAPLUS EXAMPLE
Overview
This document will assist a first-time user to send and receive a 10-Vyte pack (via UART) using the RFS ZETAPLUS modules in a terminal window. For this example, we will send a packet containing the ASCII characters HELLOWORLD” in the byte values.
Set Up
Connections The following connections are required to the Module (please note in this example “handshaking” in not required).

ZETAPLUS EXAMPLE INSTRUCTION
The ZETAPLUS requires the following pins to be connected:
Please Note: The ZETAPLUS has a shutdown pin that must be connect to GND to wake the module.
Terminal
Set up two separate terminal windows with the parameters pictured in the above image. Make sure that you have the correct COMM PORTS selected and then click on the CONNECT button in the left-hand corner.

ZETAPLUS EXAMPLE INSTRUCTION
Receiver (Part 1)
Its is first required to set the parameters for receive mode. This is achieved using the command “ATR” followed by the size of the packet which you wish to receive. For this example, we want to receive he word “HELLOWORLD”, therefore a 10-byte packet is required. The command that we send to the module via terminal is:
ATR#010
This can be seen in the below figure of the TERMINAL window. Please be aware that when using some instances of Terminal, it is required to use “#” instead of <space> or <carriage return>. This will also place the module into receive mode.
Please Note: On the ZETAPLUS module you can also set the channel (in 250KHz increments) on which you wish to receive. This is also set in the ATR command before the length of the data packet. For example, to transmit on channel 2 send the command.
ATR#002#010

ZETAPLUS EXAMPLE INSTRUCTION
Transmitter
After the receiver parameters, have been set and the receiver has been placed into the correct mode, you are now able to send the data packet from the transmitter.
ATS#002#010HELLOWORLD
After you have sent the packet via the transmitter, the receiver will output the data through the TX (UART) pin to the RX (UART) of the host (in this case PC with TERMINAL). The receiver will automatically start the outputted data with #R (to signify the start of a new packet) follow by the RSSI value (value between 0-255).
The figure below show the receive window of the receiver in TERMINAL

ZETAPLUS EXAMPLE INSTRUCTION
ADVANCED OPERATION
To reduce current consumption, the ATM command can be used, the below example shows how to set the receiver to standard RX mode. By changing the value to 2 you can set the module into a receiver/transmit mode for fast transceiver operations. By setting the value to 3 this will place the module into low power sleep mode (NOTE: The receiver will not receive in this mode).
Therefore, the require command to set the receiver on the ZETAPLUS is:
ATM#001
Figure showing ATM command being sent to set receive mode NOTE: For full command set and technical information, please see product datasheet. This can be downloaded from each product page on our website (www.rfsolutions.co.uk).

ZETAPLUS EXAMPLE INSTRUCTION
Simplified Declaration of Conformity (RED)
BG – RF Solutions Limited , 2014/53/. : www.rfsolutions.co.uk CS -Tímto RF Solutions Limited prohlasuje, ze typ rádiového zaízení definované v tomto dokumentu je v souladu se smrnicí 2014/53/EU. Úplné znní EU prohlásení o shod je k dispozici na této internetové adrese: www.rfsolutions.co.uk DA – Hermed erklærer RF Solutions Limited , at radioudstyrstypen defineret i dette dokument er i overensstemmelse med direktiv 2014/53/EU. EU-overensstemmelseserklæringens fulde tekst kan findes på følgende internetadresse: www.rfsolutions.co.uk
DE – Hiermit erklärt RF Solutions Limited , dass der Funkanlagentyp in diesem Dokument definiert der Richtlinie 2014/53/EU entspricht. Der vollständige Text der EU-Konformitätserklärung ist unter der folgenden Internetadresse verfügbar: www.rfsolutions.co.uk EL – / RF Solutions Limited , 2014/53/. : www.rfsolutions.co.uk EN – Hereby, RF Solutions Limited declares that the radio equipment type defined within this document is in compliance with Direct ive 2014/53/ EU. The full text of the EU declaration of conformity is available at the following internet address: www.rfsolutions.co.uk
ES – Por la presente, RF Solutions Limited declara que el tipo de equipo radioeléctrico definido dentro de este documento es confo rme con la Directiva 2014/53/UE. El texto completo de la declaración UE de conformidad está disponible en la dirección Internet siguiente: www.rfsolutions.co.uk
ET -Käesolevaga deklareerib RF Solutions Limited , et käesolev raadioseadme tüüp määratletud selles dokumendis vastab direktiivi 2014/53/EL nõuetele. ELi vastavusdeklaratsiooni täielik tekst on kättesaadav järgmisel internetiaadressil: www.rfsolutions.co.uk
FI -RF Solutions Limited vakuuttaa, että radiolaitetyyppi määratletud selles dokumendis on direktiivin 2014/53/EU mukainen. EUvaatimustenmukaisuusvakuutuksen täysimittainen teksti on saatavilla seuraavassa internetosoitteessa: www.rfsolutions.co.uk
FR – Le soussigné, RF Solutions Limited , déclare que l’équipement radioélectrique du type défini dans ce document est conforme à la directive 2014/53/UE. Le texte complet de la déclaration UE de conformité est disponible à l’adresse internet suivante: www.rfsolutions.co.uk
HR – RF Solutions Limited ovime izjavljuje da je radijska oprema tipa definirani u ovom dokumentu u skladu s Direktivom 2014/53/EU. Cjeloviti tekst EU izjave o sukladnosti dostupan je na sljedeoj internetskoj adresi: www.rfsolutions.co.uk
HU – RF Solutions Limited igazolja, hogy a dokumentumban meghatározottak szerint típusú rádióberendezés megfelel a 2014/53/EU irányelvnek. Az EU-megfelelségi nyilatkozat teljes szövege elérhet a következ internetes címen: www.rfsolutions.co.uk IT – Il fabbricante, RF Solutions Limited , dichiara che il tipo di apparecchiatura radio definito all’interno di questo documento è conforme alla direttiva 2014/53/UE. Il testo completo della dichiarazione di conformità UE è disponibile al seguente indirizzo Internet: www.rfs olutions.co.uk LT – As, RF Solutions Limited , patvirtinu, kad radijo rengini tipas apibrzta siame dokumente atitinka Direktyv 2014/53/ES. Visas ES atitikties deklaracijos tekstas prieinamas siuo interneto adresu: www.rfsolutions.co.uk LV – Ar so RF Solutions Limited deklar, ka radioiekrta kas defints saj dokument atbilst Direktvai 2014/53/ES. Pilns ES atbilstbas deklarcijas teksts ir pieejams sd interneta vietn: www.rfsolutions.co.uk MT – B’dan, RF Solutions Limited , niddikjara li dan it-tip ta’ tagmir tar-radju definit f’dan id-dokument huwa konformi mad-Direttiva 2014/53/UE. It-test kollu tad-dikjarazzjoni ta’ konformità tal-UE huwa disponibbli f’dan l-indirizz tal-Internet li ej: www.rfsolutions.co.uk NL – Hierbij verklaar ik, RF Solutions Limited , dat het type radioapparatuur gedefinieerd in dit document conform is met Richtlijn 2014/53/EU. De volledige tekst van de EU-conformiteitsverklaring kan worden geraadpleegd op het volgende internetadres: www.rfsolutions.co.uk
PL – RF Solutions Limited niniejszym owiadcza, e typ urzdzenia radiowego zdefiniowane w tym dokumencie jest zgodny z dyrektyw 2014/53/UE. Pelny tekst deklaracji zgodnoci UE jest dostpny pod nastpujcym adresem internetowym: www.rfsolutions.co.uk PT – O(a) abaixo assinado(a) RF Solutions Limited declara que o presente tipo de equipamento de rádio definido neste documento est á em conformidade com a Diretiva 2014/53/UE. O texto integral da declaração de conformidade está disponível no seguinte endereço de Internet: www.rfsolutions.co.uk
RO – Prin prezenta, RF Solutions Limited declar c tipul de echipamente radio definit în acest document este în conformitate cu Directiva 2014/53/UE. Textul integral al declaraiei UE de conformitate este disponibil la urmtoarea adres internet: www.rfsolutions.co.uk SK – RF Solutions Limited týmto vyhlasuje, ze rádiové zariadenie typu definované v tomto dokumente je v súlade so smernicou 2014/53/EÚ. Úplné EÚ vyhlásenie o zhode je k dispozícii na tejto internetovej adrese: www.rfsolutions.co.uk
SL – RF Solutions Limited potrjuje, da je tip radijske opreme opredeljeno v tem dokumentu skladen z Direktivo 2014/53/EU. Celotno besedilo izjave EU o skladnosti je na voljo na naslednjem spletnem naslovu: www.rfsolutions.co.uk
SV – Härmed försäkrar RF Solutions Limited att denna typ av radioutrustning definieras i detta dokument överensstämmer med direktiv 2014/53/ EU. Den fullständiga texten till EU-försäkran om överensstämmelse finns på följande webbadress: www.rfsolutions.co.uk

RF Solutions Ltd. Recycling Notice Meets the following EC Directives: DO NOT Discard with normal waste, please recycle. ROHS Directive 2011/65/EU and amendment 2015/863/EU Specifies certain limits for hazardous substances. WEEE Directive 2012/19/EU Waste electrical & electronic equipment. This product must be disposed of through a licensed WEEE collection point. RF Solutions Ltd., fufulfils its WEEE obligations by membership of an approved compliance scheme, environment agency registration number WEE/JB0104WV.

Waste Batteries and Accumulators Directive 2006/66/EC Where batteries are fitted, before recycling the product, the batteries must be removed and disposed of at a licensed collection point. RF Solutions battery producer number BPRN00060.

Disclaimer:
Whilst the information in this document is believed to be correct at the time of issue, RF Solutions Ltd does not accept any liability whatsoever for its accuracy, adequacy
or completeness. No express or implied warranty or representation is given relating to the information contained in this document. RF Solutions Ltd reserves the right to
make changes and improvements to the product(s) described herein without notice. Buyers and other users should determine for themselves the suitability of any such information or products for their own particular requirements or specification(s). RF Solutions Ltd shall not be liable for any loss or damage caused as a result of user’s own determination of how to deploy or use R F Solutions Ltd’s products. Use of RF Solutions Ltd products or components in life support and/or safety applications is not authorised except with express written approval. No licences are created, implicitly or otherwise, under any of RF Solutions Ltd’s intellectual property rights. Liability for
loss or damage resulting or caused by reliance on the information contained herein or from the use of the product (including liability resulting from negligence or where RF Solutions Ltd was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict RF Solutions Ltd’s liability for death
or personal injury resulting from its negligence.

Documents / Resources

rf solutions 433MHz ZETAPLUS Smart Transceiver Module [pdf] Instruction Manual
433MHz, 868MHz, 915MHz, 433MHz ZETAPLUS Smart Transceiver Module, 433MHz, ZETAPLUS Smart Transceiver Module, Smart Transceiver Module, Transceiver Module, Module

References

User Manual

rf solutions 433MHz ZETAPLUS Smart Transceiver Module Instruction Manual

433MHz ZETAPLUS Smart Transceiver Module

Specifications:

Product Usage Instructions:

Set Up:

Terminal Setup:

Receiver (Part 1):