RevZilla CD-LPF-RZR3 License Plate Frame With Tag Light
Specifications:
- Part Numbers: CD-LPF-RZR3
- Fitment: 2021-2024 RZR Trail, RZR Trail S, and various other models listed in the manual
- Package Contents:
- License Plate Frame (1)
- Mounting Hardware Kit (1)
- Y Harness Adapter (1)
- 6 Cable Ties (10)
Product Usage Instructions
Installation:
- Secure the vehicle on a level surface and disconnect the negative battery cable.
- Locate and unplug the 4-position rear lighting harness connector to the taillights.
- Plug the Y Harness Adapter into the rear lighting harness connectors.
- Mount the License Plate Frame in the desired location using the provided hardware.
- Route the License Plate Frame wiring towards the Y Harness Adapter and secure it with the provided Cable Ties.
- Install the Male JAE connector onto the License Plate Frame pre-pinned wires according to Figure 1.
- Connect the Male JAE connector of the Plate Frame into the Y Harness Adapter.
- Reconnect the negative battery cable and test all lighting before operating the vehicle.
FAQ:
- Q: What should I do if the license plate does not fit properly?
A: In case of improper fitment, you may need to cut or notch the license plate to allow wiring to pass through. Take caution when using power tools to avoid injury. - Q: How can I contact support for further assistance?
A: For any questions or assistance, you can email Info@CustomDynamics.com or call 1 800-382-1388 during the specified hours.
Installation Instructions
We thank you for purchasing the Custom Dynamics® SXS LED Plate Frame Kit. Our products utilize the latest technology and high quality components to ensure you the most reliable service. We offer one of the best warranty programs in the industry and we back our products with excellent customer support, if you have questions before or during installation of this product please call Custom Dynamics® at 1(800) 382-1388.
- Part Numbers: CD-LPF-RZR3
Package Contents
- License Plate Frame (1)
- Mounting Hardware Kit (1)
- Y Harness Adapter (1)
- 6″ Cable Ties (10)
Fitment: 2021-2024 RZR Trail, RZR Trail S, 2021-2022 RZR Trail S 900, 2021 RZR XP Turbo, 2019-2020 RZR-S 1000, 2015-2023 RZR XP 1000, 2018 RZR 900 XC, 2019- 2021 RZR XP Turbo S, 2016-2020 RZR XP Turbo, 2016-2018 RZR-S 1000, 2015-2020 RZR-S 900, RZR 900, 2016-2023 RZR 4 XP, 2017-2021 RZR 4 XP Turbo 1000, 2019 RZR 4 S 1000, RZR 4 XP Turbo S, 2016-2018 RZR 4 XP 900, 2016 RZR 4 XP Turbo, 2015 RZR 4 XP 1000 & RZR 4 XP 900
ATTENTION
Please read all Information below before Installation
Warning: Disconnect negative battery cable from battery; refer to owner’s manual. Failure to do so may result in electrical shock, injury, or fire. Secure negative battery cable away from positive side of battery and all other positive voltage sources on vehicle. Safety First: Always wear appropriate safety gear including safety glasses when performing any electrical work. It is highly recommended that safety glasses be worn throughout this installation process. Be sure vehicle is on level surface, secure and cool.
Important: Before beginning installation, disconnect the negative battery cable from the battery to prevent damage to the LEDs or module during installation. Damage to either as a result of direct shorting is not covered under warranty.
Important: For Proper fitment, the license plate may need to be cut or notched to allow the wiring from the frame to pass through. Take care when using power tools. Improper use can cause seri-ous injury.
Installation:
- Secure vehicle on a level surface. Disconnect negative battery cable from the battery.
- Locate and unplug the 4-position rear lighting harness connector to the taillights at the rear of the vehicle. Connector is typically located under the left side rear bed rail. Plug the Y Harness Adapter, inline, into the rear lighting harness connectors.
- Mount License Plate Frame in desired location with the provided hard-ware. Notch the license plate and or any mounting surface to allow for wires to pass though, and ensure wires are protected from any sharp edges.
- Route the License Plate Frame wiring towards the Y Harness Adapter. Secure wiring properly with the provided 6” Cable Ties. Note: Pinched, pulled, cut or frayed wires are not covered under warranty.
- Install the provided Male JAE connector onto the License Plate Frame pre-pinned wires by pushing the pins into the connector ports according to Figure1. Pins should click in place and not pull back out of connector when installed correctly. The black wire goes into Port 1 and the white wire goes into Port 2.
- Connect the Male JAE connector of the Plate from into the Y Harness Adapter.
- Reconnect the negative battery cable and reinstall any panels needed to access wiring.
- Test operation of all lighting before operating the vehicle.
Questions?
- Email: Info@CustomDynamics.com
- Call us at: 1 800-382-1388
- M-TH 8:30AM-5:30PM /
- FR 9:30AM-5:30PM EST
Documents / Resources
![]() |
RevZilla CD-LPF-RZR3 License Plate Frame With Tag Light [pdf] Instructions CD-LPF-RZR3 License Plate Frame With Tag Light, CD-LPF-RZR3, License Plate Frame With Tag Light, Plate Frame With Tag Light, Frame With Tag Light, Tag Light, Light |