REV A SHELF I-4WDIVCC-0225 Deep Drawer Divider Insert Installation Guide

I-4WDIVCC-0225 Deep Drawer Divider Insert

Product Information

Specifications:

  • Product Name: Craftsman Collection Deep Drawer Divider
    Insert
  • Model Number: I-4WDIVCC-0225
  • Material: Steel
  • Quantity: 1 set (2 Uprights, 1 Steel Pins)
  • Dimensions: 4 x 4 inches
  • Manufacturer: Rev-A-Shelf

Product Usage Instructions

Tools Required:

#2 Phillips Head Screwdriver

Care and Maintenance:

Clean with a damp cloth and wipe parts dry regularly to maintain
product quality.

Installation Steps:

  1. Identify the uprights (A) and steel pins (D).
  2. Place the uprights in the drawer at desired locations.
  3. Insert the steel pins into the system holes of the uprights to
    secure them in place.
  4. To install dividers at an angle, offset the top steel pin by
    one system hole.

For visual installation guidance, visit www.rev-a-shelf.com/videos.

FAQ (Frequently Asked Questions)

Q: Can the Craftsman Collection Deep Drawer Divider Insert be
adjusted for different drawer sizes?

A: Yes, the dividers can be positioned at various distances to
fit different drawer dimensions.

Q: How should I clean the divider insert?

A: Use a damp cloth to clean the insert and ensure all parts are
dried thoroughly after cleaning.

“`

12400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126
INSTALLATION INSTRUCTIONS / INSTRUCCIONES DE INSTALACIÓN / INSTRUCTIONS D’INSTALLATION
CRAFTSMAN COLLECTION DEEP DRAWER DIVIDER INSERT ORGANIZADOR PARA CAJONES PROFUNDOS CRAFTSMAN COLLECTION ORGANISATEUR DE TIROIR PROFOND CRAFTSMAN COLLECTION
TOOLS REQUIRED: HERRAMIENTAS REQUERIDAS:
OUTILS REQUIS:
#2

CARE AND MAINTENANCE: CUIDADO/ENTRETIEN:
Clean with a damp cloth and wipe parts dry.
Limpie con un paño húmedo y seque las partes.
Nettoyez avec un linge humide et essuyez les piéces pour les secher complétement.
VIDEO TUTORIAL VIDEO TUTORIAL TUTOTIEL VIDÉO

PARTS LIST / LISTA DE PIEZAS / LISTE DES PIÈCES

No.

Description / Descripción / La description

A

Uprights / Puntales / Tiges

B

Anti-Skid Mat / Estera antideslizante / Tapis antidérapant

C

Divider / Divisores / Séparateurs

D

Steel Pins / Pasadores de acero / Goupilles en acier

E

#8 x 1″ Phillips Flat Head Screws / Tornillos de cabeza plana Phillips #8 x 1″ / Vis à tête plate Phillips #8 x 1 po

*Dependent on size purchased / *Depende de la unidad adquirida / *Dépendant de la taille achetée

Qty. 2 1
4, 5, 6* 20, 24, 30*
4

x 4 WWW.REV-A-SHELF.COM/VIDEOS

I-4WDIVCC-0225

Note: Uprights can be trimmed if needed. Nota: Los puntales se pueden cortar si es necesario. Remarque : Les montants peuvent être coupés si nécessaire.

#2
X4
Note: Repeat Steps 1 & 2 for the front of the drawer. Nota: Repita los pasos 1 y 2 para el frente del cajón. Remarque : Répétez les étapes 1 et 2 pour l’avant du tiroir.

3

4

Note: To install any of the Dividers at an angle, offset the top Steel Pin by one system hole.

Nota: Para instalar cualquiera de los divisores en ángulo, desplace el

pasador de acero superior en un orificio del sistema.

Remarque : Pour installer l’un des séparateurs en biais, décalez la

goupille en acier supérieure d’un trou du système.

5
Note: Dividers can be trimmed if needed. Max trim of 1/4″ on each side of Divider. Nota: Los separadores se pueden recortar si es necesario. Recorte máximo de 6mm a cada lado del divisor. Remarque : Les séparateurs peuvent être coupés si nécessaire. Garniture maximale de 6 mm de chaque côté du séparateur.

12400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126

Documents / Resources

REV A SHELF I-4WDIVCC-0225 Deep Drawer Divider Insert [pdf] Installation Guide
I-4WDIVCC-0225 Deep Drawer Divider Insert, I-4WDIVCC-0225, Deep Drawer Divider Insert, Drawer Divider Insert, Divider Insert

References

Leave a comment

Your email address will not be published. Required fields are marked *