RC-33 Bluetooth Voice Remote Control
“
Product Specifications
- Product Name: Bluetooth Voice Remote Control
- Model Name: RC-33
- Bluetooth Version: 4.0
- Operating Range: Up to 4 meters
- Battery: 2 AAA batteries (not included)
Product Usage Instructions
Pairing the Remote Control
- Press and hold the [] key] and []
key] simultaneously for about 3 seconds until the indicator
starts flashing. - Turn on your host device’s Bluetooth.
- Search for devices and connect to the RC-33 device name.
- If pairing is successful, the red light on the remote control
will stay on for 1.5 seconds. - If pairing fails after 30 seconds, the red light will turn
off.
Battery Low Notification
When the battery power is lower than 2.4V, the red light will
flash for 3 seconds at a frequency of 1Hz every time a key is
pressed.
Sleep and Wake Up Function
The remote control will stay connected for 2 hours without
disconnection. After 2 hours of inactivity, it will enter sleep
mode. Press any key to wake up the remote control. If still
connected, the corresponding key Bluetooth code value will be
sent.
Product Caution
Any changes or modifications not approved by the manufacturer
may void your authority to operate this equipment. This device
complies with FCC rules and should be operated with a minimum
distance of 0cm between the radiator and your body.
Frequently Asked Questions (FAQ)
Q: How do I know if the pairing was successful?
A: If pairing is successful, the red light on the remote control
will stay on for 1.5 seconds.
Q: What should I do if the battery is low?
A: When the battery power is lower than 2.4V, the red light will
flash for 3 seconds at a frequency of 1Hz every time a key is
pressed.
“`
The product name is Bluetooth voice remote control model name is RC-33. Product description:
instructions
device nameRC-33
Press and hold the [
] key] and [ ] key on the remote control at the same time for about
3 seconds to work the indicator flashing, indicating that you have entered pairing mode. Turn on
Host Bluetooth – click host Bluetooth – Search for devices – Connect to the “RC-33” device name
and connect. If pairing is successful, the red light of the remote control stays on for 1.5 seconds;
if pairing fails after 30 seconds, the red dot goes out Equipment
When the battery power is lower than 2.4V, Every time the user presses a key, Press any key, the red light flflashes for 3s, and the frequency is 1Hz
At 4 meters, the remote control is connected to the TV for at least 2 hour without disconnection. If
the pairing information is available and the Bluetooth connection is broken, press any key to send
the corresponding infrared code and send it back to broadcast for 5 seconds, return the success
indicator light to Flash 3 times.In the case of matching information, the remote control power back
to broadcast 5 seconds, back to success,The indicator light does not indicate
4. sleep and wake up Without any data interaction, the remote control keeps connected for 2 hour and then enters into the state of sleep disconnection, press any key to wake up the remote control, if still connected, then send the corresponding key Bluetooth code value; If you have entered the Bluetooth connection disconnect state, you will enter the backconnect state,After successful connection,Press any key to send the corresponding Bluetooth code value;
When the TV is turned on, the upgrade fifile of the remote controller is detected. If the upgrade fifile exists, the remote controller performs OTA upgrade, and the LED lamp flflashes. At this time, the remote controller can’t be used, and any buttons don’t respond. After the upgrade is successful, the LED light stops flflashing, and the remote controller can be used normally at this time. If the upgrade fails, it will be detected and upgraded again at the next boot. After OTA fails, the LED light stops flflashing, and the remote controller returns to the old version for normal operation.
. Bluetooth remote control
FCC Warnning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.
Documents / Resources
 |
RETROSUN RC-33 Bluetooth Voice Remote Control [pdf] User Manual RC-33, 2BDAL-RC-33, 2BDALRC33, RC-33 Bluetooth Voice Remote Control, RC-33, Bluetooth Voice Remote Control, Remote Control, Control |