RENU WP6101TN Plus Web Panel
Product Code
INTRODUCTION
The WP6 Plus is a ThinClient with an inbuilt browser, which connects to a remote Web server on its network. All WP6 devices are compliant with EMC directive 2014/30/EU and LVD directive 2014/35/EU and certified for UL Class I Div. 2.
SPECIFICATIONS
| Power | 24VDC (+20%), 350mA , 8.5W |
|
Display |
1024 x 600pixels , 10.1″ Color TFT,
WSVGA Web Panel Analog Resistive Touch Screen |
|
Memory |
eMMC: 4GB RAM: 1GB |
| USB Ports | 1 USB Slave and USB Host |
| Ethernet | 1 Ethernet Port |
| Panel Cutout | 256.00(W) x 178.00(H)mm |
| Dimensions | 268.00(W) x 190.00(H) x 33.00(D)mm |
| Weight | Approx. 900gm |
| LED | 1 |
| Environment & Approvals | |
| Operating Temperature | 0 to 50°C |
| Storage Temperature | -30 to 85°C |
| Humidity | 10 to 90% (Noncondensing) |
|
Shock |
IEC 60068-2-27
25g, 11ms, 6 shocks per axis, total 18 shocks (X, Y, Z) |
|
Vibration |
IEC 60068-2-6
5 to 150Hz, 3g peak (X, Y, Z) |
|
EMC |
EN 55011 : 2009/A1 :2010
EN 61131-2 : 2007 EN 61000-6-2 : 2005/AC : 2005 EN 61000-6-4: 2007/A1: 2011 |
| Protection | Front panel-IP66, Rare panel-IP20 |
|
Approvals |
CE, UL,REACH ,UKCA & RoHS
compliant |
Default Product Settings
| Network Settings | DHCP |
| Brightness | Full Scale |
| Screen Touch Beeper | On |
| Default Language | English |
PRODUCT DIMENSIONS
PANEL CUTOUT DIMENSIONS
- Panel Cutout Dimensions: 256.00 (W) x 178.00(H)mm
- Panel Thickness: Maximum 6mm
- Mounting Clamps: 6
Tighten the mounting screws evenly to a torque between 0.4N/m to maintain water and dust resistance.
COMMUNICATION
- This section provides information regarding communication interfaces supported by this product.
RJ45/Ethernet Port
- Th e WP6 Plus series devices come with an in-built RJ45/Ethernet port. The RJ45 port is a shielded female jack with link and activity LEDs.
| Pin number | Signal |
| 1 | TX+ |
| 2 | TX- |
| 3 | RX+ |
| 4 | NC |
| 5 | NC |
| 6 | RX- |
| 7 | NC |
| 8 | NC |
USB Slave Port (2.0)
- The WP6 Plus comes with a Type C USB device port.
USB Host Port
- The WP6 Plus devices support one USB Host port that connects to a USB 2.0 compatible USB Flash drive.
- This port can be used to upgrade the firmware and the browser.
| Pin number | Signal |
| 1 | VCC |
| 2 | D- |
| 3 | D+ |
| 4 | GND |
GETTING STARTED
To use the WP6 Plus as a browser, follow these steps to connect the device to a Webserver. The Password for configuring the device is admin@123. [Note: For configuring new Password it must be at least 7 or more charterers with 1 capital letter (0-9, a-z, A-Z)]
- Connect an Ethernet cable to the device.
- Power up the device using 24VDC power supply by connecting it to the device’s pluggable terminal block.
- If the browser or the firmware needs to be updated, connect a USB flash drive to the device.
MAIN SETTINGS
Earthing
The optimum method for Earthing electronic equipment is to earth it separately from other high-power systems and to earth more than one unit of electronic equipment with a single-point earth. The Earthing marked terminal (see below) is provided on the unit.
UL APPROVAL
CONTROL DRAWING NO# CNTL/DWG/FP6101/0218 VER.N O.: 1.00
Capacitance and inductance of the field wiring from the nonincendive equipment to the associated apparatus shall be calculated and must be included in the system calculations as shown in Table 1.| Whore the cable capacitance and inductance one foot are not known. the following values shall be used: Ccable = 60 pF/ft., Lcabie = 0.2 pH/T.
WARNINGS
- This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D or non-hazardous locations only.
- WARNING – EXPLOSION HAZARD – Do not disconnect equipment unless power has been removed or the area is known to be non-hazardous.
- WARNING – EXPLOSION HAZARD – Substitution of components may impair suitability for Class I, Division 2.
- The list of materials used in the construction of these devices with name of sealed device, the generic name of the material and the supplier’s name and type designation.
- It is recommended that the user periodically inspect the sealed devices used, for any degradation of properties and replace the device if any degradation is found.
REVISION HISTORY
| Rev. | Description | Date |
| 1.4 | Specification details updated | 09/06/2025 |
| 1.3 | Specification details updated | 23/04/2024 |
| 1.2 | Renu Logo updated | 19/05/2023 |
| 1.1 | Added password information | 14/10/2021 |
| 1.0 | First Draft | 11/06/2021 |
Renu Electronics Pvt. Ltd® reserves the right to change or discontinue specifications and features without prior notice. To view the latest and updated datasheets/manuals please visit www.renuelectronics.com.
Frequently Asked Questions
1. What is the default password for configuring the device?
The default password for configuring the device is admin@123. For a new password, it must be at least 7 characters long with at least 1 capital letter.
Documents / Resources
 |
RENU WP6101TN Plus Web Panel [pdf] User Guide WP6 101 TN Plus, WP6101TN Plus Web Panel, WP6101TN Plus, Web Panel, Panel |