Regal ideas 2AB4JLEDAC LEDAC LED Low Voltage Control Unit and RF Remote Control
This device is a Class B digital device that complies with Part 15 of the FCC Rules. It is designed to provide reasonable protection against harmful interference in a residential installation. The device generates and radiates radio frequency energy and should be installed and used in accordance with the provided instructions to avoid causing interference to radio communications.
Specifications
- Compliance: Part 15 of FCC Rules
- Device Class: Class B digital device
- RF Radiation Exposure Limits: Compliant with FCC’s and IC’s standards
- Antenna Requirement: Must be installed with a separation
distance of at least 20 cm from all persons
Product Usage Instructions
- Installation: Do not power on the device before completing installation. Follow the provided instructions carefully to ensure proper setup.
- Control: Use the designated App to control the devices connected to this controller. Ensure the App is installed and set up correctly for seamless operation.
NOTE:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received,including interference that may cause undesired operation.
Changes or modifications to this unit not expressly approved by theparty responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:· Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
The following RF exposure warning is only for RF CONTROLLER
This equipment complies with FCC’s and IC’s RF radiation exposure limits set forth for an uncontrolled environment. The antenna(s) used for this transmitter must be installed and operated to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. Installers must ensure that 20cm separation distance will be maintained between the device and users.
Connect and install the device completely.
Warning:
Do not power on the device before completed installation.
Use remote control to control device :
Must completed matching the remote control with device before control.
Matching steps
Step1: Power on, the light strips will turn on.
Step 2: Remove the plastic spacer on the battery,and make sure the remote control works oronerv.
Step 3: Long press the “ON” button on the remote control, if the light strip flashed three times, the match succeeded.
Warning:
if need to change remote control, first cut off the power for device, then power on and match with new remote control. Do not match and power off several devices at the same time. if need to change remote control, first cut off the power for device, then power on and match with new remote control. Do not match and power off several devices at the same time.
Use App to control
Open the App Click “Register” to register your account and log in.
Warning:
please allow relevant App access rights
- Bluetooth Access
- Network Access
- Location Access
(Otherwise, you may not be able to connect)
Step 2:
Open WiFi, Bluetooth and location on phone, and connect WiFi. ( Currently, 5G is not available.)
Step 3:
Open “Regal Ideas” App, click the add device icon in the upper right corner of thehome screen, and select the corresponding device. (Follow the prompts to operate.)
Step 4:
Click and go to WiFi Setting, input WiFi password and go to the next step.
Step 5:
The device is registering the Cloud, hold on 1-2 minutes.
Step 6:
Click the “Completed” button in the upper right corner to customize the device name. You can control the devices by App now.
More intelligent functions:
Home Management mode
Intelligent automation
According to weather, time and setting Prepare and customize the executio program Modularization an automatic execution
FAQs
Q: What should I do if the device causes interference?
A: If the device causes harmful interference to radio or television reception, try the following measures:
- Turn the equipment off and on to determine the interference source.
- Ensure that the antenna(s) are installed with a separation distance of at least 20 cm from all persons.
- Avoid collocating the antenna with any other transmitter.
- Maintain a 20cm separation distance between the device and users.
Q: Can I operate this device without following the installation instructions?
A: No, it is crucial to complete the installation process as per the instructions provided to ensure proper functioning and compliance with FCC regulations.
Documents / Resources
 |
Regal ideas 2AB4JLEDAC LEDAC LED Low Voltage Control Unit and RF Remote Control [pdf] User Guide 2AB4JLEDAC, 2AB4JLEDAC LEDAC LED Low Voltage Control Unit and RF Remote Control, LEDAC LED Low Voltage Control Unit and RF Remote Control, LED Low Voltage Control Unit and RF Remote Control, Low Voltage Control Unit and RF Remote Control, RF Remote Control, Remote Control, Control |
