WLB5SPT-Y Portable Folding Work Light with Tripod
“
Product Information
Specifications:
- Model: WLB5SPT-Y
- Type: Portable Folding Worklight with Tripod
- Features: Tilt adjustment, Hi/Low/O switch, Easy grip handle,
Lamp, Directional knob, Battery socket
Product Usage Instructions
Safety Instructions:
- Read all safety and operating instructions before use.
- Avoid looking directly at the lighted lamps to prevent eye
injuries. - Keep the work light away from flammable surfaces or
materials. - Check for damaged or worn-out parts before use and replace or
repair as needed. - Do not use a pressure washer to clean the product.
- Do not modify the work light as it may impair function and
safety. - Store the work light in a secure place out of reach of
children.
Cleaning and Maintenance:
Before cleaning the LED work light, disconnect it from the power
source and allow it to cool down. Clean with a dry or slightly
moist lint-free cloth and mild detergent if necessary. Do not use
abrasive or solvent cleaners. Check the battery socket and housing
for damage before each use and remove any dirt or obstructions that
could cause overheating.
Assembly Instructions:
- Tripod Setup: Set up the tripod for
stability. - Install Lamp Head onto Tripod: Align the lamp
head with the tripod’s threaded socket and tighten securely. To
remove, unscrew the threaded knob and lift off.
Frequently Asked Questions (FAQ)
Q: Can I adjust the brightness of the work light?
A: Yes, the work light features a Hi/Low/O switch for adjusting
brightness levels.
Q: Is it safe to clean the work light with abrasive
cleaners?
A: No, only use a dry or slightly moist lint-free cloth with
mild detergent for cleaning. Avoid abrasive or solvent
cleaners.
Q: How should I store the work light when not in use?
A: Store the work light in a secure place out of the reach of
children. Inspect it for good working condition before storage and
before each use.
“`
Model: WLB5SPT-Y
PORTABLE FOLDING WORKLIGHT WITH TRIPOD
SAVE THESE INSTRUCTIONS READ ALL INSTRUCTIONS CAUTION: Read all safety and operating instructions in this manual
before attempting to use this product. Failure to follow instructions listed below may result in electric shock, fire and/or serious personal injury.
WARNING:
Do not look directly at the lighted lamps to avoid eye injuries.
Always keep the work light away from any flammable surface or materials.
Always check damaged or worn-out parts before using the work light. Broken parts will affect the work light operation. Replace or repair damaged or worn-out parts immediately. If repairs are needed, consult a qualified and professional electrician.
Do not use a pressure washer to clean this product.
Do not modify the work light in any way. Unauthorized modifications may impair the function and/or safety and could affect the life of the product. There are specific applications for which the work light was designed.
Store work light in a secure place out of the reach of children. Inspect the work light for good working condition prior to storage and before use.
Tilt adjustment
Hi/Low/O( switch
Easy grip handle
Lamp
Directional knob Tripod
Battery socket
WARNING:
CARE: Before cleaning the LED work light, disconnect
from power source, allow the fixture to cool down. Clean with a dry or slightly moist clean lint free cloth using a small amount of mild detergent if needed. DO NOT use abrasive or solvent cleaners.
MAINTAINANCE: Check the battery socket and
fixture housing for any damage before each use. Clean any dirt or obstruction from the housing and lens before using as this could cause overheating.
Tripod mounting bar
Tripod adjustment
ASSEMBLY INSTRUCTIONS
1) Tripod Setup
The tripod comes folded and requires no assembly. To unfold the tripod, unscrew to loosen the tripod adjustment knob located at the bottom of the tripod where the three legs meet. At the same time move the support legs away from the center tube of the tripod and push down on the center leg connector to extend the three legs. The legs should extend until they are flat. There is a line on the lower part of the tripod tube that indicates where the legs should be locked in place. Retighten tripod adjustment knob. Next, adjust the height of the center pole. To adjust height, loosen the tripod adjustment knob on the tripod and raise the pole sections. Firmly tighten the adjustment knob once you have adjusted the center pole to the desired height.
2) Install lamp head onto tripod
Set the portable light stand with lamp onto the tripod. Align the tripod threaded knob on the portable lamp with the center hole of the tripod’s threaded socket and tighten. To remove portable stand, unscrew the tripod threaded knob and lift oE.
Tripod threaded knob
Documents / Resources
 |
RED ROCK LIGHTING WLB5SPT-Y Portable Folding Work Light with Tripod [pdf] Instruction Manual WLB5SPT-Y Portable Folding Work Light with Tripod, WLB5SPT-Y, Portable Folding Work Light with Tripod, Work Light with Tripod, Light with Tripod, with Tripod |