RC Electronics Application For Setting Up R/C Model Throws User Guide

RC-Electronics-LOGO

RC Electronics Application For Setting Up R/C Model Throws

RC-Electronics-Application-For-Setting-Up-R-C-Model-Throws-PRODUCT

Specifications

Platform Android only (no iOS app at the moment)
Communication BLE (Bluetooth Low Energy) via EDGE sensors
EDGE sensors supported (Free) 1 (model view) / up to 4 (measure mode)
EDGE sensors supported (Subscription) Up to 4 (measure mode); two EDGE sensors simultaneously in model view
Models saved locally (Free) 1
Models saved locally (Subscription) Unlimited
Models synced to RCmodelsport (Free) 1
Models synced to RCmodelsport (Subscription) Unlimited
Public model data Free: yes (view/usage); Subscription: yes (view/usage)
Throw units Degrees (°) and millimeters (mm, requires chord length)
Max throws information Free: hidden; Subscription: shown (checks across flight phases/controls)
Graphical presentation of left/right throws Free: not available; Subscription: available
Language support Multi-language support
Models editing Public models are read-only (edit mode/settings hidden)
Verification tolerance (measurement) Correct when within ±0.2° (green check mark)
Model type support Currently only GLIDER type supported
Chord length behavior If chord length is 0: mm not displayed; mm requires chord length > 0

Quick Setup & Use

  1. Install and open the app. If a new version is available, the app informs you on the main menu when opened.
  2. Android BLE prerequisites: allow fine location permission, enable the Bluetooth module, and enable location service—otherwise BLE communication will not work.
  3. Connect sensors in the app (green background on EDGE live data indicates successful connection).
  4. Prepare your model in “My Models”: select an existing model or tap Add new (Free: only one model; Subscription: unlimited).
  5. Set up the 0° reference using “Offset Wing / Elevator”:
    1. Choose a stable reference point on a fixed part of the wing/elevator.
    2. Place the EDGE sensor there and press SET REFERENCE.
    3. Use SET IMG to take a photo of the reference location (optional reminder).
    4. Set current offset values to 0.0° and return to Model view.
    5. Place the EDGE sensor on the control surface position that represents the model’s true 0° and press SET REFERENCE again; enter the resulting offset so the control position shows 0°.
  6. Configure throws in Model view: select the control surface, use Measurement Mode arrows or Edit Mode SET buttons to adjust min/max/zero.
  7. For measurement, use Measure view to measure throws quickly; to display mm, enter chord length and toggle units.

Introduction

  • The application helps users quickly and accurately set up their R/C model throws using the EDGE product from RC Electronics (https://www.rc-electronics.eu/product/edge/).
  • Users can add personal notes and store all throw settings for each flight phase and control mode, whether global or specific to a particular flight phase.

Modes of operation:

  • Free
  • Yearly “EDGE PRO” subscription-based (subscription is paid via www.rcmodelspot.com) platform where the user creates his profile.

Main differences are:RC-Electronics-Application-For-Setting-Up-R-C-Model-Throws-FIG-2

Key features

  • Personal model repository which is synced to the www.rcmodelspot.com cloud
  • Public models repository for easier setting up of production models
  • Fast and accurate setting of model throws using up, down, and ok arrows
  • Graphical presentation of throws
  • Multi EDGE sensor support (up to 4)
  • Multi-language support

Important facts to know

  • For Android users: Since the app uses BLE (Bluetooth Low Energy) communication, the user must allow fine location permission.
  • User must enable the BT module and enable location service. If all are not enabled, then BLE communication will not work!RC-Electronics-Application-For-Setting-Up-R-C-Model-Throws-FIG-3

Using the application

  • After running the app, the main screen comes up. If there is a new version available on the Google Play Store, the app will inform the user on the main menu every time the app is opened.

My models:

  • User can find a list of his own models and select one to see throws, mixes, and model data and use it to fine-tune, correct, or change anything on the model.

Public models:

  • There is a list of public models that the user can use to set his model to settings as recommended by the manufacturer.

Measure:

  • Quick and simple measure menu to measure throws.RC-Electronics-Application-For-Setting-Up-R-C-Model-Throws-FIG-4

EDGE logo:

  • Indication of number of detected Edge devices. If there is a newer version available for the EDGE sensor module, the update button will appear here.

RCmodelspot:

RCmodelspot setting

Cloud Integration and Account Options

  • Even though this option appears last in the menu, let’s start with it. The EDGE app is connected to the www.rcmodelspot.com cloud service.
  • This cloud service allows you to store your model data online and automatically sync it between your Android devices if you use more than one for setting up your models.

Using EDGE in Free Mode

  • You don’t need an account on www.rcmodelspot.com to use the free version of the app. In this case, your model settings is stored locally on your device. Keep in mind that if you uninstall the app, your local data will be lost.
  • However, if you’d like to keep your model data safe even in free mode, you can choose to store your models in the RCmodelspot cloud. This way, your data remains available if you uninstall and later reinstall the app.RC-Electronics-Application-For-Setting-Up-R-C-Model-Throws-FIG-5

Using EDGE in Subscription Mode

  • To use Subscription Mode, you’ll need an RCmodelspot account. This is because your subscription is linked directly to your RCmodelspot account.
  • Creating an account on www.rcmodelspot.com is free. Once your account is set up, you can purchase a yearly subscription and then log in to your account from the EDGE app using your RCmodelspot login details.

Checking Your Subscription

  • After logging into the app, you can easily see how long your EDGE PRO subscription is valid.

My models

  • When you open “My models”, the first thing you’ll see is a list of your available models. From here, select the model you want to view or configure. If no models are listed, tap “Add new” to create one and continue.
  • In the Free version of the app, you can add only one model. In Subscription Mode, however, the number of models you can add is unlimited.
  • Pressing on an option icon (3 dots) will offer an option to copy the model or to delete it. Once deleted, it will also be removed from the RCmodelspot cloud!
  • After selecting a model, the Model View screen will appear. This view displays the layout based on your current model settings. To open the Model Settings, tap the Edit icon located in the top-right corner of the screen.RC-Electronics-Application-For-Setting-Up-R-C-Model-Throws-FIG-6 RC-Electronics-Application-For-Setting-Up-R-C-Model-Throws-FIG-7

My models settings

  • In model settings, the user can set model parameters like wing type, elevator type, and model type, and enter some information to display it in “Model view”.

Name

  • Set the name of the model. This name will be used in a “My models” list.

Model type

  • Select model type from the list. It will change the model silhouette in “Model view” in the future; at the moment, only GLIDER type is supported.

Wing / Elevator type

  • Set wing type used on model (number of ailerons and flap servos). Set elevator type (1 / 2 control or V-tail).

Weight / CG

  • Set the weight of the plane that is used when settings are made and at which CG. This is just reference info for the user.RC-Electronics-Application-For-Setting-Up-R-C-Model-Throws-FIG-8

Offset wing/elevator

  • This is a critical option which, when used correctly, significantly improves the accuracy and usability of the application and EDGE sensors, especially for future features.
  • The main challenge when setting up a model is defining what truly represents a 0° flap or aileron position. In other words, which flight phase should be considered the true 0° reference from which all other flight phases are derived?
  • On models with ailerons only, this is usually straightforward, as the aileron aligns with the fixed portion of the wing. However, on models where the flap runs all the way to the fuselage with no fixed wing section, defining 0° becomes problematic.
  • Even on wings that do have a fixed section next to the flap, it is often unclear whether that section truly represents a 0° flap position or whether it already has some built-in deflection due to manufacturing tolerances.
  • Using a flap position as the 0° reference is also unreliable. Servos may have mechanical play, or trim adjustments may have been applied during flight and later forgotten, resulting in an incorrect reference and a misaligned wing setup.
  • These challenges are exactly what the Offset Wing / Elevator function is designed to solve.
  • The core idea of the application design is to establish a stable reference point on a fixed part of the wing or elevator—a point that does not move during flight and is not affected by servo inaccuracies. Once the user selects such a point, it is always used as the reference by pressing “SET REFERENCE.” Because the application measures the difference between two angles rather than absolute values, the aircraft’s tilt during measurement does not affect the result.RC-Electronics-Application-For-Setting-Up-R-C-Model-Throws-FIG-9
  • After choosing the reference point, place the EDGE sensor there and use “SET IMG” to take a photo showing its location. This can be the same or a different point for the wing and elevator, depending on user preference.
  • The photo serves as a reminder of the selected reference point.
  • Next, ensure that the current offset values are set to 0.0°. Go to the Model view, place the EDGE sensor on the fixed reference point, and press “SET REFERENCE.” Then move the EDGE sensor to the model’s control surface at the user-defined 0° position (aileron or flap, depending on the model). The angle displayed now represents the required offset value for the wing or elevator.
  • For example, if the EDGE sensor shows +1.8° on the flap after setting the reference on the fixed wing section, the user should enter –1.8° as the wing offset. Once this is done, returning to the Model view will show 0° when the EDGE sensor is placed on the model’s true 0° control position.
  • From that point forward, whenever the user wants to measure control throws or make adjustments, they simply place the EDGE sensor on the reference point, press “SET REFERENCE,” and then move the sensor to the control surface.
  • All measurements will be accurate and repeatable.
  • This method also ensures consistency across multiple models from the same manufacturer. All models will share the same 0° reference position and identical flight phase deflections.
  • One reference point is used for all wing servos, and a separate reference point is used for elevator servos. On T-tail and X-tail gliders, the wing reference point may also be used.
  • On V-tail models, however, the elevator reference point must be used, and the fuselage must be banked so the elevator is horizontal during measurement.
  • At any time during setup or measurement, the user can place the EDGE sensor on the reference point and press “SET REFERENCE” to re-establish the baseline.

Flight phases

  • The list of flight phases in use. User can add/change/rename/sort flight phases.
  • Pressing an option button on flight phases will offer additional options which are self-explanatory. To reorder the flight phases, press and hold the 2-line icon and drag it up / down on the list.RC-Electronics-Application-For-Setting-Up-R-C-Model-Throws-FIG-10

Control modes

Control mode is a control stick on user transmitter or a switch. Control mode is for example: aileron, elevator, rudder, gear, … Butterfly for example may be used as a global control mode which is only set once and same value is seen over all flight phases. User can add/change/rename/sort/add global control mode. Once control mode is set, user has option to set throws of that control mode in “Model view” and also set mixes with other controls.RC-Electronics-Application-For-Setting-Up-R-C-Model-Throws-FIG-11

  • For example,when Aileron control mode is selected, all of the wing control surface offsets are visible per flight phase setting along with their deflections up/ down (throws).
  • If we are carefull we can also see how much aileron / Flap mix is used and how much aileron / rudder mixing is used. Each flight phase can have difrent throws and mixes for same control mode.

Picture on right says:

  • When user uses 100% of aileron stick, outer ailerons will deflect +-15.2°, inner ailerons for +-12.1°, outer flaps for +-8.7° and inner flaps for +-5.1°. At the same time rudder will deflect for +-12.9°RC-Electronics-Application-For-Setting-Up-R-C-Model-Throws-FIG-12
  • Next example (left picture) will show how much snap flap is used when the user moves the elevator: the whole wing goes up for 1.9°and down for 2.7° when the user moves 100% of the elevator stick; at the same time, the elevator makes +-12° deflectionRC-Electronics-Application-For-Setting-Up-R-C-Model-Throws-FIG-13

Model view

  • In the Model View, you can use the app to configure your model or record the throw settings you currently use. Saving these throws allows you to easily apply the same setup to your next model.
  • Depending on your configuration, you’ll see your settings, flight phases, and controls displayed at the top of the screen. In the center, you’ll find the throw values for each control surface of your model (for example, two ailerons, two flaps, and a V-tail as shown in the image).
  • Below that, you’ll see the EDGE sensor live data. In the example image, the background is green, meaning the EDGE sensor is successfully connected.
  • To switch between control surfaces, use the < and > arrows next to the control surface name, or tap one of the gray bubbles showing throw information.
  • The selected control surface will be highlighted with a red outline, and its name will appear below the EDGE logo.RC-Electronics-Application-For-Setting-Up-R-C-Model-Throws-FIG-14
  • The next section displays the throw values in either degrees (°) or millimeters (mm), depending on the unit selected with the Units slider located at the bottom of the screen.
  • When Edit Mode is turned off, the displayed values represent relative deflections from the 0° or 0 mm baseline as measured by the EDGE sensor.
  • Inside each control bubble, you’ll see the minimum and maximum values relative to current Flight Phase zero.
  • In Measurement Mode (Edit Mode off), arrows appear to guide you while adjusting your throws. These arrows indicate whether the throw should be increased or decreased.
  • Once a green check mark appears, it means the throw is correctly set within a ±0.2° margin.
  • In Edit Mode, you can adjust the current minimum, maximum, and zero control positions using the SET buttons, or manually enter values using the keyboard. RC-Electronics-Application-For-Setting-Up-R-C-Model-Throws-FIG-15

Note:

  • When Edit Mode is enabled, the values displayed in the fields are relative to the current zero position. These will automatically be converted to values relative to the 0 position of the EDGE sensor’s reference data.
  • While Edit Mode is active, unit switching is disabled — you cannot toggle between degrees and millimeters.
  • The MIRROR button also becomes available in this mode. By pressing MIRROR, the app copies your current control values to the corresponding mirrored control surface.
  • For example, pressing MIRROR will copy the left aileron data to the right aileron, and vice versa.
  • The Chord length represents the length of the control surface. If the chord length is set to 0, the throws will not be displayed in millimeters. Once a chord length value is entered, the throws for that control surface can be viewed in both degrees and millimeters.
  • Below the throws area, the user can find a notes area where the user can write down any special notes which are stored to the model.
  • Then he can find max throws information. Max throws will be displayed in °or mm (depends on units setting). Max throw goes over all Flight phases and all controls and finds min and max throw for each control.
  • This information is visible only on “subscription” version. “Free” version has this information hidden.RC-Electronics-Application-For-Setting-Up-R-C-Model-Throws-FIG-16
  • Wing and elevator reference images are displayed at the end so the user knows where the reference point is.
  • Application will automatically take wing reference for all wing control surfaces and elevator offset for all elevator surfaces!
  • When the user has the “subscription” version, he can use two EDGE sensors at the same time in “model” view.

Difference will be:

  • Having left and right side SET REFERENCE button ( one for each sensor)
  • EDGE sensor ID will be shown in the EDGE logo
  • Once application detects EDGE sensor it will automatically gave it the correct ID. So first detected sensor will have ID 1 and 2nd detected will have ID 2. The ID for the sensor is displayed with number of blinks on sensor (one blink or 2 blinks).
  • Sensor ID 1 shoud be used on left side of model and on the controls which are only one (like elevator single servo and rudder). For all right sided control surfaces sensor ID 2 must be used.RC-Electronics-Application-For-Setting-Up-R-C-Model-Throws-FIG-17

Public models

  • When you open “Public Models”, you’ll see a list of all available public model profiles. This list will continue to grow over time as more data becomes available.
  • If you’re a model manufacturer, feel free to contact us at support@rc-electronics.eu — we’ll be happy to add your model to the list.
  • After selecting a public model, the view works the same way as in “My Models”, with one difference: public models cannot be edited or changed. You can use the data provided to fine-tune your own model or to review the throws and mixes used.
  • Because public profiles are read-only, the Settings icon and Edit Mode are disabled and hidden from view.RC-Electronics-Application-For-Setting-Up-R-C-Model-Throws-FIG-18

Measure

  • The Measure View is designed for quick and simple throw measurements.
  • In the Free version of the app, up to four EDGE sensors is supported. The Subscription version, however, also shows a graphic view of Edge pair throws.
  • To set an EDGE sensor to zero, simply tap on the sensor’s green live data field.
  • If you’d like to display throws in millimeters (mm), toggle the units setting in the top-right corner of the screen.
  • Note: To view throws in mm, you must enter the chord length of the control surface.
  • If the chord length is set to 0, the app will display throws only in degrees (°).
  • Chord length values are saved temporarily and will reappear the next time you open Measure View. These values are not linked to any specific model settings.
  • To temporarily save the minimum or maximum throw from sensor data, tap the corresponding Max Up or Max Down value field — the current measurement will be stored there. RC-Electronics-Application-For-Setting-Up-R-C-Model-Throws-FIG-19

Revision history

April 2026 In measure mode, free version now supports up to 4 Edge sensors.
January 2026 Initial release of user manual.

CUSTOMER SERVICE

Links to the application

Troubleshooting

  • EDGE/BLE communication not working (Android): ensure you have allowed fine location permission, enabled the Bluetooth module, and enabled location service. If any are not enabled, BLE communication will not work.
  • Throws show only in degrees (°), not millimeters (mm): mm display requires a non-zero chord length. If chord length is set to 0, the app will not display throws in mm.
  • Reference/throw accuracy seems off: re-establish the baseline by placing the EDGE sensor on your selected reference point and pressing SET REFERENCE again during setup or measurement.
  • Green check mark not appearing when adjusting throws: the app indicates correctness when set within a ±0.2° margin.

Documents / Resources

PDF thumbnailApplication For Setting Up R/C Model Throws
User Guide · Application For Setting Up R-C Model Throws, Setting Up R-C Model Throws, Model Throws

References

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.