Raspberry Pi Pico 2 W should comply with relevant regulations
and standards applicable in the country of intended use. The power
supply provided should be 5V DC with a minimum rated current of
1A.

Compliance Certificates:

For all compliance certificates and numbers, please visit
www.raspberrypi.com/compliance.

Integration Information for the OEM:

The OEM/Host product manufacturer should ensure continued
compliance to FCC and ISED Canada certification requirements once
the module is integrated into the Host product. Refer to FCC KDB
996369 D04 for additional information.

Regulatory Compliance:

For products available on the USA/Canada market, only channels 1
to 11 are available for 2.4GHz WLAN. The device and its antenna(s)
must not be colocated or operated in conjunction with any other
antenna or transmitter except in accordance with FCC’s
multi-transmitter procedures.

FCC Rule Parts:

The module is subject to the following FCC rule parts: 15.207,
15.209, 15.247, 15.401, and 15.407.

FAQ

Q: What should be the power supply for Raspberry Pi Pico 2
W?

A: The power supply should provide 5V DC and a minimum rated
current of 1A.

Q: Where can I find compliance certificates and numbers?

A: For all compliance certificates and numbers, please visit
www.raspberrypi.com/compliance.

“`

View Fullscreen

Raspberry Pi Pico 2 W Safety and User
guide
Designed and distributed by 194 Cambridge Science Park Milton Road Cambridge CB4 0AB United Kingdom UK www.raspberrypi.com
Raspberry Pi Regulatory compliance and safety information
Product name: Raspberry Pi Pico 2 W
IMPORTANT: PLEASE RETAIN THIS INFORMATION FOR FUTURE REFERENCE.
Warnings · Any external power supply used with the
Raspberry Pi shall comply with relevant regulations and standards applicable in the country of intended use. The power supply should provide 5V DC and a minimum rated current of 1A.
Instructions for safe use · This product should not be overclocked. · Do not expose this product to water or
moisture, and do not place it on a conductive surface whilst in operation. · Do not expose this product to heat from any source; it is designed for reliable operation at normal room temperatures. · Do not expose board to high intensity light sources (e.g. xenon flash or laser) · Operate this product in a well-ventilated environment, and do not cover it during use. · Place this product on a stable, flat, nonconductive surface while in use, and do not let it contact conductive items. · Take care while handling this product to avoid mechanical or electrical damage to the printed circuit board and connectors. · Avoid handling this product while it is powered. Only handle by the edges to minimize the risk of electrostatic discharge damage. · Any peripheral or equipment used with the Raspberry Pi should comply with relevant standards for the country of use and be marked accordingly to ensure that safety and performance requirements are met. Such equipment includes, but is not limited to, keyboards, monitors, and mice.
For all compliance certificates and numbers, please visit www.raspberrypi.com/compliance.

Raspberry Pico W · Raspberry Pi 5V DC 1A · · · · · , · · · · Raspberry Pi www.raspberrypi.com/compliance
Cestina Raspberry Pi Pico 2 W DLEZITÉ: TUTO INFORMACI SI PONECHTE PRO POUZITÍ V BUDOUCNU. Varování

· Kazdý externí napájecí zdroj pouzitý s Raspberry Pi musí splovat píslusné pedpisy a normy platné v zemi urcení. Napájecí zdroj by ml poskytovat stejnosmrné naptí 5V a minimální jmenovitý proud 1A. Pokyny pro bezpecné pouzívání
· Tento výrobek by neml být petaktován. · Výrobek nevystavujte vod ani vlhkosti a
za provozu ho neumisujte na vodivý povrch.
· Výrobek nevystavujte teplu z jakéhokoli zdroje; je navrzen pro spolehlivý provoz pi normálních pokojových teplotách.
· Nevystavujte desku svtelným zdrojm s vysokou intenzitou (nap. Xenonový blesk nebo laser)
· Výrobek pouzívejte v dobe vtraném prostedí a za provozu ho nepikrývejte.
· Výrobek pi pouzívání ponechte na stabilním, plochém a nevodivém povrchu a zabrate jeho dotyku s vodivými pedmty.
· Pi manipulaci s výrobkem dbejte na to, abyste zabránili mechanickému nebo elektrickému poskození desky plosných spoj a konektor.
· Vyvarujte se manipulace s výrobkem, kdyz je napájen. K manipulaci pouzívejte pouze okraje, abyste minimalizovali riziko poskození elektrostatickým výbojem.
· Veskerá periferní a dalsí zaízení
pouzívaná s Raspberry Pi by mla být v
souladu s píslusnými normami zem
pouzití a mla by být odpovídajícím
zpsobem oznacena, aby se zajistilo, ze
splují pozadavky na bezpecnost a
výkon. Vsechna osvdcení o shod a
císla najdete na
www.raspberrypi.com/compliance. Dansk
Raspberry Pi Pico 2 W
VIGTIGT: OPBEVAR DENNE
INFORMATION FOR FREMTIDIG
REFERENCE. Advarsler
· Eksterne strømforsyninger, der anvendes til Raspberry Pi skal være i overensstemmelse med relevante bestemmelser og standarder, som er gældende i det land, hvor anvendelsen er tiltænkt. Strømforsyningen skal give 5 V jævnstrøm og en nominel strømstyrke på mindst 1A. Instruktioner for sikker brug
· Dette produkt må ikke overophedes. · Udsæt ikke dette produkt for vand eller
fugt, og sæt det ikke på en ledende overflade under drift.
· Udsæt ikke dette produkt for varme fra nogen kilder; det er designet til pålidelig drift ved normal stuetemperatur.
· Udsæt ikke kortet for lyskilder med høj intensitet (f.eks. Xenon-flash eller laser)
· Anvend dette produkt i et godt ventileret miljø, og tildæk det ikke under brug.
· Anbring dette produkt på en stabil, flad og ikke-ledende overflade under brug, og lad det ikke komme i berøring med ledende genstande.
· Vær forsigtig ved håndtering af dette produkt for at undgå mekanisk eller elektrisk beskadigelse af printkort og stik.
· Undgå håndtering af dette produkt, mens det er tændt. Må kun håndteres ved at holde i kanterne for at minimere risikoen for skader ved elektrostatisk udladning.
· Alt perifert udstyr eller udstyr, der anvendes til Raspberry Pi skal overholde relevante standarder i landet for anvendelse og mærkes i overensstemmelse hermed for at sikre, at kravene for sikkerhed og ydeevne er opfyldt. For alle overensstemmelsescertifikater og numre, gå på www.raspberrypi.com/compliance. Nederlands
Raspberry Pi Pico 2 W BELANGRIJK: BEWAAR DEZE INFORMATIE VOOR TOEKOMSTIGE VERWIJZING.
Waarschuwingen
· Elke externe voeding die met de Raspberry Pi wordt gebruikt, moet voldoen aan de relevante voorschriften en normen die van toepassing zijn in het land van het beoogde gebruik. De voeding moet 5V DC en een minimale nominale stroom van 1A leveren. Instructies voor veilig gebruik
· Dit product mag niet overklokt worden.
· Stel dit product niet bloot aan water of vocht en plaats het tijdens gebruik niet op een geleidend oppervlak.
· Stel dit product niet bloot aan warmte van welke bron dan ook; het is ontworpen voor betrouwbare werking bij normale kamertemperatuur.
· Stel het bord niet bloot aan lichtbronnen met een hoge intensiteit (bijv. Xenonflits of laser)
· Gebruik dit product in een goed geventileerde omgeving en dek het niet af tijdens gebruik.
· Plaats dit product tijdens het gebruik op een stabiel, plat, niet-geleidend oppervlak en laat het niet in contact komen met geleidende items.
· Wees voorzichtig met het gebruik van dit product om mechanische of elektrische schade aan de printplaat en connectoren te voorkomen.
· Gebruik dit product niet terwijl het wordt gevoed. Alleen aan de randen vasthouden om het risico op schade door

elektrostatische ontlading te minimaliseren. · Alle randapparatuur of apparatuur die met
de Raspberry Pi wordt gebruikt, moet
voldoen aan de relevante normen voor
het land van gebruik en
dienovereenkomstig worden gemarkeerd
om ervoor te zorgen dat wordt voldaan
aan de veiligheids- en prestatie-eisen.
Ga naar
www.raspberrypi.com/compliance. Suomi
Raspberry Pi Pico 2 W TÄRKEÄÄ: SÄILYTÄ NÄMÄ TIEDOT
MYÖHEMMÄN KÄYTÖN VARALTA.
Varoituksia
· Kaikkien ulkoisen Raspberry Pi -laitteessa käytettyjen virtalähteiden on noudatettava käyttömaassa sovellettavia asiaankuuluvia asetuksia ja standardeja. Virtalähteen virran on oltava 5V DC minimin nimellisvirran ollessa 1A. Ohjeet turvallista käyttöä varten
· Tätä tuotetta ei saa ylikuormittaa.
· Älä altista tätä tuotetta vedelle tai kosteudelle, äläkä aseta sitä johtavalle
pinnalle sen ollessa toiminnassa.
· Älä altista tätä tuotetta mistään lähteestä aiheutuvalle kuumuudelle; se on suunniteltu luotettavaa toimintaa varten normaaleissa huonelämpötiloissa.
· Älä altista korttia korkean intensiteetin valonlähteille (esim. Ksenonlamppu tai laser)
· Käytä tätä tuotetta hyvin ilmastoidussa lämpötilassa, äläkä peitä sitä käytön aikana.
· Aseta tämä tuote vakaalle, tasaiselle, eijohtavalle pinnalle sen ollessa käytössä, äläkä anna sen koskettaa johtavia kohteita.
· Noudata varovaisuutta tätä tuotetta käsiteltäessä mekaanisen tai sähköisen vaurioitumisen estämiseksi painetulle piirilevylle ja liittimille.
· Vältä tämän tuotteen käsittelyä sen ollessa kytkettynä virtalähteeseen. Käsittele vain reunoista sähköstaattisen purkautumisen vaaran minimoimiseksi.
· Kaikkien Raspberry Pi -laitteiden kanssa käytettävien oheislaitteiden ja muiden laitteiden on oltava käyttömaan asianmukaisten standardien mukaisia, ja niiden on oltava merkittyjä sen varmistamiseksi, että turvallisuus ja suorituskykyvaatimukset täytetään. Lisätietojen saamiseksi kaikista vaatimustenmukaisuussertifikaateista vieraile verkkosivustolla www.raspberrypi.com/compliance.
Français
Raspberry Pi Pico 2 W IMPORTANT: VEUILLEZ CONSERVER CETTE INFORMATION POUR VOUS Y REPORTER ULTÉRIEUREMENT. Avertissements
· Toute alimentation électrique externe utilisée avec le Raspberry Pi doit être conforme aux réglementations et normes applicables dans le pays d’utilisation. L’alimentation électrique doit fournir 5 V CC et un courant nominal minimum de 1A. Consignes pour une utilisation en toute sécurité
· Ce produit ne doit pas être utilisé à une vitesse supérieure à celle prévue pour son usage.
· N’exposez pas ce produit à l’eau ou à l’humidité et ne le placez pas sur une surface conductrice pendant le fonctionnement.
· N’exposez pas ce produit à la chaleur quelle qu’en soit la source; il est conçu pour un fonctionnement fiable à des températures ambiantes normales.
· N’exposez pas la carte à des sources de lumière de haute intensité (par exemple flash au xénon ou laser)
· Faites fonctionner ce produit dans un environnement bien ventilé et ne le couvrez pas pendant l’utilisation.
· Placez ce produit sur une surface stable, plane et non conductrice pendant son utilisation et ne le laissez pas en contact avec des éléments conducteurs.
· Faites attention lors de la manipulation de ce produit pour éviter tout dommage mécanique ou électrique au niveau de la carte de circuit imprimé et des connecteurs.
· Évitez de manipuler ce produit lorsqu’il est sous tension. Ne manipulez que par les bords afin de minimiser les risques de dommages dus aux décharges électrostatiques.
· Tout périphérique ou équipement utilisé avec le Raspberry Pi doit être conforme aux normes applicables dans le pays
d’utilisation et être marqué en conséquence pour garantir la sécurité et les performances.
Pour tous les certificats et numéros de conformité, veuillez consulter www.raspberrypi.com/compliance
Deutsch
Raspberry Pi Pico 2 W WICHTIG: BITTE BEWAHREN SIE DIESE
INFORMATIONEN FÜR ZUKÜNFTIGE
REFERENZ.
Achtung
· Jedes externe Netzteil, das mit dem Raspberry Pi verwendet wird, muss den einschlägigen Vorschriften und Normen entsprechen, die im Bestimmungsland gelten. Die Stromversorgung sollte 5 V

Gleichstrom und einen minimalen Nennstrom von 1A liefern. Anweisungen für die sichere Verwendung · Dieses Produkt sollte nicht übertaktet werden. · Setzen Sie dieses Produkt nicht Wasser oder Feuchtigkeit aus und stellen Sie es während des Betriebs nicht auf eine leitfähige Oberfläche. · Setzen Sie dieses Produkt keiner Wärmequelle aus. Es ist für einen zuverlässigen Betrieb bei normalen Raumtemperaturen ausgelegt. · Stel het bord niet bloot aan lichtbronnen met een hoge intensiteit (bijv. Xenonflits of laser) · Betreiben Sie dieses Produkt in einer gut belüfteten Umgebung und decken Sie es während des Gebrauchs nicht ab. · Stellen Sie dieses Produkt während des Gebrauchs auf eine stabile, flache, nicht leitende Oberfläche und lassen Sie es nicht mit leitfähigen Gegenständen in Berührung kommen. · Seien Sie vorsichtig beim Umgang mit diesem Produkt, um mechanische oder elektrische Schäden an der Leiterplatte und den Anschlüssen zu vermeiden. · Vermeiden Sie die Handhabung dieses Produkts während der Stromversorgung. Produkt nur an den Rändern anfassen, um das Risiko von elektrostatischen Entladungsschäden zu minimieren. · Alle Peripheriegeräte oder Geräte, die mit dem Raspberry Pi verwendet werden, müssen den geltenden Normen für das jeweilige Land entsprechen und entsprechend gekennzeichnet sein, um zu gewährleisten, dass die Sicherheits- und Leistungsanforderungen erfüllt werden. Alle Konformitätszertifikate und -nummern finden Sie auf www.raspberrypi.com/compliance .
Italiano
Raspberry Pi Pico W
IMPORTANTE: CONSERVARE QUESTE INFORMAZIONI PER RIFERIMENTO FUTURO. Avvisi · Tutti gli alimentatori esterni utilizzati con il Raspberry Pi devono essere conformi alle normative e agli standard pertinenti applicabili nel paese di utilizzo previsto. L’alimentatore utilizzato dovrà fornire 5 V CC e una corrente nominale minima di 1A. Istruzioni per l’utilizzo in sicurezza · Questo prodotto non deve essere overcloccato. · Non esporre questo prodotto all’acqua o all’umidità e non collocarlo su una superficie conduttiva mentre è in funzione. · Non esporre questo prodotto a fonti di calore. Il prodotto è progettato per un funzionamento affidabile solo alla normale temperatura ambiente. · Non esporre la scheda a fonti di luce ad alta intensità (ad esempio flash allo xeno o laser) · Utilizzare questo prodotto in un ambiente ben ventilato e non coprirlo durante l’uso. · Per l’uso, collocare questo prodotto su una superficie stabile, piana e non conduttiva. Evitare che venga in contatto con oggetti conduttivi. · Durante l’uso o lo spostamento del prodotto prestare attenzione ad evitare danni meccanici o elettrici al circuito stampato e ai connettori. · Evitare di maneggiare questo prodotto mentre è alimentato. Afferrare solo dai bordi per ridurre al minimo il rischio di danni da scariche elettrostatiche.
· Tutte le periferiche e le apparecchiature
utilizzate con il Raspberry Pi devono
essere conformi agli standard pertinenti
per il paese di utilizzo ed essere dotate
del relativo marchio a garanzia della
conformità con i requisiti di sicurezza e prestazioni necessari.
Per informazioni su numeri e certificati di
conformità, visitare www.raspberrypi.com/compliance.
Raspberry Pi Pico 2 W :
· Raspberry Pi

5V DC
1A

·
·

·
Raspberry Pi

www.raspberrypi.com/compliance

Raspberry Pi Pico 2 W : .

· Raspberry Pi
,
.
5V DC, 1A
.

· ” .
· ,

.
·
.
.
· ( :
) .
·
, .
·
,
.
·
,
.
·
.

.
· Raspberry Pi
,

.
,
. www.raspberrypi.com/compliance.
Polski
Raspberry Pi Pico W WANE: PROSIMY ZACHOWA TE INFORMACJE NA PRZYSZLO. Ostrzeenia · Wszelkie zewntrzne ródla zasilania uywane z Raspberry Pi powinny by zgodne z odpowiednimi przepisami i normami obowizujcymi w kraju przeznaczenia. Zasilacz powinien zapewnia napicie 5V DC i minimalny prd znamionowy 1A. Instrukcje bezpiecznego uytkowania · Ten produkt nie powinien by przetaktowany. · Nie naley wystawia tego produktu na dzialanie wody ani wilgoci, ani umieszcza go na powierzchni przewodzcej podczas pracy. · Nie naley wystawia tego produktu na dzialanie ciepla z jakiegokolwiek ródla; produkt zaprojektowano tak, aby dzialal niezawodnie w normalnej temperaturze pokojowej. · Nie wystawiaj plyty na dzialanie ródel wiatla o wysokiej intensywnoci (np. Ksenonowej lampy blyskowej lub lasera) · Uywa w dobrze wentylowanym otoczeniu i nie zakrywa podczas uytkowania. · Podczas uytkowania naley umieci produkt na stabilnej, plaskiej, nieprzewodzcej powierzchni i nie dopuci do kontaktu z przedmiotami przewodzcymi prd. · Naley zachowa ostrono podczas obchodzenia si z produktem, aby unikn mechanicznego lub elektrycznego uszkodzenia plyty z obwodami drukowanymi i zlczy. · Nie naley przenosi produktu, gdy jest podlczony do zasilania. Trzyma wylcznie za krawdzie, aby

zminimalizowa ryzyko uszkodzenia w wyniku wyladowa elektrostatycznych. · Wszelkie urzdzenia peryferyjne lub sprzt uywany z Raspberry Pi powinny by zgodne z odpowiednimi normami dla kraju uytkowania i by odpowiednio oznakowane, aby zapewni spelnienie wymaga bezpieczestwa i wymogów eksploatacyjnych. Wszystkie certyfikaty zgodnoci i numery mona znale na stronie www.raspberrypi.com/compliance.
Português do Brasil
Raspberry Pi Pico 2 W IMPORTANTE: POR FAVOR, GUARDE
ESTAS INFORMAÇÕES PARA
REFERÊNCIA FUTURA.
Avisos
· Qualquer fonte de alimentação externa usada com o Raspberry Pi deve cumprir
os regulamentos e normas aplicáveis no país de utilização. A fonte de alimentação
deve fornecer 5V CC e uma corrente nominal mínima de 1A.
Instruções para o uso seguro
· Este produto não deve ser usado em overclock.
· Não exponha este produto à água ou à umidade, e não o coloque em uma
superfície condutora durante a operação.
· Não exponha este produto ao calor de qualquer fonte; Ele é projetado para operação confiável à temperatura ambiente.
· Não exponha a placa a fontes de luz de alta intensidade (por exemplo, flash xenon
ou laser)
· Opere este produto em um ambiente bem ventilado e não o cubra durante o uso.
· Coloque este produto em uma superfície estável, plana e não condutora durante o uso, e não deixe que entre em contato
com dispositivos que conduzem eletricidade.
· Tome cuidado ao manusear este produto para evitar danos mecânicos ou elétricos à placa de circuito impresso e aos conectores.
· Evite manusear este produto enquanto estiver ligado. Somente manuseie pelas bordas (laterais) para minimizar o risco de dano por descarga eletrostática.
· Qualquer periférico ou equipamento usado com o Raspberry Pi deve cumprir os
padrões de fabricação e uso relevantes
para o país e assim garantir que os
requisitos de segurança e desempenho
sejam atendidos. Para todos os certificados conformidade e
números, visite
www.raspberrypi.com/compliance.
P Raspberry Pi Pico 2 W : . ! · , Raspberry Pi, , . 5 1. · . · . · ; . · (, ) · . · , , . · , . · . , . · , Raspberry Pi, . , , www.raspberrypi.com/compliance .
Español
Raspberry Pi Pico 2 W IMPORTANTE: POR FAVOR CONSERVE
ESTA INFORMACIÓN PARA FUTURA
REFERENCIA.
Advertencias

· Cualquier fuente de alimentación externa utilizada con la Raspberry Pi deberá cumplir con las correspondientes regulaciones y normas aplicables en el país de uso previsto. La fuente de alimentación debe proporcionar 5V DC y una corriente nominal mínima de 1A. Instrucciones para un uso seguro
· Este producto no debe ser usado con una frecuencia de reloj superior a la nominal. (No se debe overclockear).
· No exponga este producto al agua o a la humedad, y no lo coloque sobre una superficie conductora mientras está en funcionamiento.
· No exponga este producto a ningún tipo de fuente de calor; está diseñado para un funcionamiento fiable a temperatura ambiente normal.
· No exponga la placa a fuentes de luz de alta intensidad (por ejemplo, flash de xenón o láser)
· Utilice este producto en un ambiente bien ventilado, y no lo cubra durante el uso.
· Coloque este producto sobre una superficie estable, plana y no conductora mientras esté en uso, y no permita que entre en contacto con elementos conductores.
· Tenga cuidado al manipular este producto para evitar daños mecánicos o eléctricos en la placa de circuito impreso y en los conectores.
· Evite manipular este producto mientras está encendido. Sujételo solo por los bordes para minimizar el riesgo de daños
por descargas electrostáticas. · Cualquier periférico o equipo utilizado con
la Raspberry Pi debe cumplir con las
normas aplicables en el país de uso y
debe estar marcado en consecuencia
para garantizar que se cumplen los
requisitos de seguridad y rendimiento.
Para obtener todos los certificados de
conformidad y sus números de registro,
visite www.raspberrypi.com/compliance.
Svenska Raspberry Pi Pico 2 W VIKTIGT: BEHÅLL DENNA
INFORMATION FÖR FRAMTIDA
REFERENS.
Varningar · Alla externa strömförsörjningar som
används med Raspberry Pi måste uppfylla alla tillämpliga regler och standarder i det land där de används. Strömförsörjningen måste tillhandahålla 5 VDC och ha en lägsta märkström på 1A. Instruktioner för säker användning · Produkten bör inte överklockas. · Utsätt inte produkten för vatten eller fukt, och placera den inte på en ledande yta medan den är i drift. · Utsätt inte produkten för värme från någon värmekälla. Den är utformad för tillförlitlig drift vid normal rumstemperatur. · Utsätt inte kortet för ljuskällor med hög intensitet (t.ex. xenon-blixt eller laser) · Använd produkten i en väl ventilerad miljö, och täck inte över den vid användning. · Placera produkten på en stabil, isolerad yta vid användning, och låt den inte komma i kontakt med ledande föremål. · Var försiktig när du hanterar produkten för att undvika mekaniska eller elektriska skador på kretskortet och kontakterna. · Undvik att hantera produkten med strömmen på. Håll den endast i kanterna för att undvika elektrostatiska urladdningar. · Eventuell kringutrustning och utrustning som används med Raspberry Pi måste uppfylla relevanta standarder i det land där den används, och den bör märkas så att säkerhets- och prestandakraven uppfylls. Besök www.raspberrypi.com/compliance, för alla certifikat och nummer om överensstämmelse.
EU Radio Equipment Directive (2014/53/EU)
Declaration of Conformity (DoC)
We, Raspberry Pi Limited, 194 Cambridge Science Park, Milton Road, Cambridge, CB4 0AB United Kingdom, Declare under our sole responsibility that the product: Raspberry Pi Pico 2 W to which this declaration relates is in conformity with the essential requirements and other relevant requirements of the Radio Equipment Directive (2014/53/EU). The product is in conformity with the following standards and/or other normative documents: SAFETY (art 3.1.a): IEC 60950-1: 2005 (2nd Edition) and EN 62311: 2008 EMC (art 3.1.b): EN 301 489-1/ EN 301 489-17 Ver. 3.1.1 (assessed in conjunction with ITE standards EN 55032 and EN 55024 as Class B equipment) SPECTRUM (art 3. 2): EN 300 328 Ver 2.1.1, EN 301 893 V2.1.0 In accordance with Article 10.8 of the Radio Equipment Directive: The device `Raspberry Pi Pico 2 W ‘ operates in compliance with harmonised standard EN 300 328 v2.1.1 and transceives within the frequency band 2,400 MHz to 2,483.5 MHz and, as per Clause 4.3.2.2 for wideband modulation type equipment, operates at a maximum e.i.r.p. of 20dBm. The device `Raspberry Pi Pico 2 W also operates in compliance with harmonised standard EN 301 893 V2.1.1.). In accordance with Article 10.10 of the Radio Equipment Directive, and as per below list of country codes, the operating bands 5150-5350MHz are strictly for indoor usage only.

CZ DK

IE EL

IT CY

H U

PT RO

SE UK

The Raspberry Pi complies with the relevant provisions of the RoHS Directive for the European Union. WEEE Directive Statement for the European Union This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling. Note: A full online copy of this Declaration can be found at www.raspberrypi.com/compliance/

WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov.
FCC Raspberry Pi Pico 2 W FCC ID: 2ABCB-PICO2W This device complies with Part 15 of FCC Rules, Operation is Subject to following two conditions:(1) This device may not cause harmful interference, and (2) This device must accept any interference received including interference that cause undesired operation. Caution: Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void user s authority to operate the equipment. This equipment has been tested and found to comply within the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Re-orient or relocate the receiving antenna · Increase the separation between the equipment and receiver
· Connect the equipment into an outlet on a different circuit from that to which the receiver is connected · Consult the dealer or an experienced radio/TV technician for help.
For products available on the USA/Canada market, only channels 1 to 11 are available for 2.4GHz WLAN
This device and its antenna(s) must not be colocated or operation in conjunction with any other antenna or transmitter except in accordance with FCC’s multi-transmitter procedures.

IMPORTANT NOTE: FCC Radiation Exposure Statement; Co-location of this module with other transmitter that operate simultaneously are required to be evaluated using the FCC multitransmitter procedures. This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The device contains an integral antenna hence, the device must be installed to so that a separation distance of at least 20cm from all persons. Raspberry Pi Pico 2 W IC: 20953-PICO2W This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
For products available on the USA/Canada market, only channels 1 to 11 are available for 2.4GHz WLAN Selection of other channels is not possible. Pour les produits disponibles sur le marché USA / Canada, seuls les canaux 1 à 11 sont disponibles pour le réseau local sans fil 2,4 GHz. La sélection d’autres canaux n’est pas possible. This device and its antenna(s) must not be co-located with any other transmitters except in accordance with IC multi-transmitter product procedures. Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association avec une autre antenne ou transmetteur. réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux. IMPORTANT NOTE: IC Radiation Exposure

Statement: This equipment complies with IC RSS102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum separation distance of 20cm between the device and all persons. Cet équipement est conforme aux limites d’exposition au rayonnement IC RSS-102 définies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance de séparation minimale de 20 cm entre l’appareil et toutes les personnes.
INTEGRATION INFORMATION FOR THE OEM
It is the responsibility of the OEM / Host product manufacturer to ensure continued compliance to FCC and ISED Canada certification requirements once the module is integrated in to the Host product. Please refer to FCC KDB 996369 D04 for additional information. The module is subject to the following FCC rule parts: 15.207, 15.209, 15.247, 15.401And 15.407
Host Product User Guide Text
FCC Compliance This device complies with Part 15 of FCC Rules, Operation is Subject to following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received including interference that cause undesired operation.
Caution: Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void user s authority to operate the equipment.
This equipment has been tested and found to comply within the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Re-orient or relocate the receiving antenna · Increase the separation between the equipment and receiver · Connect the equipment into an outlet on a different circuit from that to which the receiver is connected · Consult the dealer or an experienced radio/TV technician for help. For products available in the USA/Canada market, only channels 1 to 11 are available for 2.4GHz WLAN. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter except in accordance with FCC’s multi-transmitter procedures.
ISED Canada Compliance
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.For products available in the USA/Canada market, only channels 1 to 11 are available for 2.4GHz WLAN Selection of other channels is not possible.Pour les produits disponibles sur le marché USA / Canada, seuls les canaux 1 à 11 sont disponibles pour le réseau local sans fil 2,4 GHz. La sélection d’autres canaux n’est pas possible. This device and its antenna(s) must not be co-located with any other transmitters except in accordance with IC multi-transmitter product procedures. Cet appareil et son antenne (s) ne doit pas être colocalisés ou fonctionnement en association avec une autre antenne ou transmetteur.
IMPORTANT NOTE: IC Radiation Exposure Statement: This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum separation distance of 20cm between the device and all persons. Cet équipement est conforme aux limites d’exposition au rayonnement IC RSS-102 définies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance de séparation minimale de 20 cm entre l’appareil et toutes les personnes.
Host Product Labelling; The host product must be labelled with the following information:
“Contains TX FCC ID: 2ABCB-PICO2W” “Contains IC: 20953-PICO2W ”
“This device complies with Part 15 of FCC Rules, Operation is Subject to following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received including interference that cause undesired operation.”
Important Notice to OEMs: The FCC Part 15 text must go on the Host product unless the product is too small to support a label

with the text on it. It is not acceptable just to place the text in the user guide.
E-Labelling It is possible for the Host product to use e-labelling providing the Host product supports the requirements of FCC KDB 784748 D02 e labelling and ISED Canada RSS-Gen, section 4.4.
E-labelling would be applicable for the FCC ID, ISED Canada certification number and the FCC Part 15 text.
Changes in Usage Conditions of this Module
This device has been approved as a Mobile device in accordance with FCC and ISED Canada requirement. This means that there must be a minimum separation distance of 20cm between the Module’s antenna and any persons. A change in use that involves a separation distance 20cm (Portable usage) between the Module’s antenna and any persons is a change in the RF exposure of the module and, hence, is subject to a FCC Class 2 Permissive Change and a ISED Canada Class 4 Permissive Change policy in accordance with FCC KDB 996396 D01 and ISED Canada RSP-100. As noted above, This device and its antenna(s) must not be co-located with any other transmitters except in accordance with IC multi-transmitter product procedures. If the device is co-located with multiple antennas, the module could be subject to a FCC Class 2 Permissive Change and a ISED Canada Class 4 Permissive Change policy in accordance with FCC KDB 996396 D01 and ISED Canada RSP-100. In accordance with FCC KDB 996369 D03, section 2.9, test mode configuration information is available from the Module manufacturer for the Host (OEM) product manufacturer.
Spain “La operación de este equipo está sujeta a las siguientes dos condiciones”1. Es posible que este equipo o dispositivo no cause interferencia perjudicial.2. Este equipo o dispositivo debe aceptar cualquier interferencia. Incluyendo la que pueda causar su operación no deseada.
Australia and New Zealand Class B Emissions Compliance Statement Warning: This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

xxxYYY APPROVED

Documents / Resources

Raspberry Pi Pico 2 W Microcontroller Board [pdf] User Guide
PICO2W, 2ABCB-PICO2W, 2ABCBPICO2W, Pico 2 W Microcontroller Board, Pico 2 W, Microcontroller Board, Board

References

User Manual

Raspberry Pi Pico 2 W Microcontroller Board User Guide

Pico 2 W Microcontroller Board

Product Information

Specifications:

Product Usage Instructions

Safety Information: